blob: 1df6855ccaf67f4b4e4fb5911f8f07feef92a3be [file] [log] [blame]
Peter Tyser1f03cbf2008-12-23 16:32:00 -06001/*
2 * Copyright 2008 Extreme Engineering Solutions, Inc.
3 * Copyright 2004-2008 Freescale Semiconductor, Inc.
4 *
5 * See file CREDITS for list of people who contributed to this
6 * project.
7 *
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License as
10 * published by the Free Software Foundation; either version 2 of
11 * the License, or (at your option) any later version.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
21 * MA 02111-1307 USA
22 */
23
24/*
25 * xpedite5200 board configuration file
26 */
27#ifndef __CONFIG_H
28#define __CONFIG_H
29
30/*
31 * High Level Configuration Options
32 */
33#define CONFIG_BOOKE 1 /* BOOKE */
34#define CONFIG_E500 1 /* BOOKE e500 family */
35#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
36#define CONFIG_MPC8548 1
37#define CONFIG_XPEDITE5200 1
38#define CONFIG_SYS_BOARD_NAME "XPedite5200"
39#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
40#define CONFIG_RELOC_FIXUP_WORKS /* Fully relocate to SDRAM */
41
42#define CONFIG_PCI 1 /* Enable PCI/PCIE */
43#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
44#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
45#define CONFIG_PCI1 1 /* PCI controller 1 */
46#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
47#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
48#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
49
50/*
51 * DDR config
52 */
53#define CONFIG_FSL_DDR2
54#undef CONFIG_FSL_DDR_INTERACTIVE
55#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
56#define CONFIG_DDR_SPD
57#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
58#define SPD_EEPROM_ADDRESS 0x54
59#define CONFIG_NUM_DDR_CONTROLLERS 1
60#define CONFIG_DIMM_SLOTS_PER_CTLR 1
61#define CONFIG_CHIP_SELECTS_PER_CTRL 2
62#define CONFIG_DDR_ECC
63#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
64#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
65#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
66#define CONFIG_VERY_BIG_RAM
67
68#define CONFIG_SYS_CLK_FREQ 66666666
69
70/*
71 * These can be toggled for performance analysis, otherwise use default.
72 */
73#define CONFIG_L2_CACHE /* toggle L2 cache */
74#define CONFIG_BTB /* toggle branch predition */
75#define CONFIG_ENABLE_36BIT_PHYS 1
76
77/*
78 * Base addresses -- Note these are effective addresses where the
79 * actual resources get mapped (not physical addresses)
80 */
81#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
82#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */
83#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
84#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
85#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR + 0x8000)
86
87/*
88 * Diagnostics
89 */
90#define CONFIG_SYS_ALT_MEMTEST
91#define CONFIG_SYS_MEMTEST_START 0x10000000
92#define CONFIG_SYS_MEMTEST_END 0x20000000
93
94/*
95 * Memory map
96 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
97 * 0x8000_0000 0xbfff_ffff PCI1 Mem 1G non-cacheable
98 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
99 * 0xe800_0000 0xe87f_ffff PCI1 IO 8M non-cacheable
100 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
101 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
102 * 0xf800_0000 0xfbff_ffff NOR Flash 2 64M non-cacheable
103 * 0xfc00_0000 0xffff_ffff NOR Flash 1 64M non-cacheable
104 */
105
106#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3)
107
108/*
109 * NAND flash configuration
110 */
111#define CONFIG_SYS_NAND_BASE 0xef800000
112#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
113#define CONFIG_SYS_MAX_NAND_DEVICE 1
114#define CONFIG_NAND_ACTL
115#define CONFIG_SYS_NAND_ACTL_CLE (1 << 3) /* ADDR3 is CLE */
116#define CONFIG_SYS_NAND_ACTL_ALE (1 << 4) /* ADDR4 is ALE */
117#define CONFIG_SYS_NAND_ACTL_NCE (0) /* NCE not controlled by ADDR */
118#define CONFIG_SYS_NAND_ACTL_DELAY 25
119
120/*
121 * NOR flash configuration
122 */
123#define CONFIG_SYS_FLASH_BASE 0xfc000000
124#define CONFIG_SYS_FLASH_BASE2 0xf8000000
125#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
126#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
127#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
128#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
129#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
130#define CONFIG_FLASH_CFI_DRIVER
131#define CONFIG_SYS_FLASH_CFI
132#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
133 {0xfbf40000, 0xc0000} }
134#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
135
136/*
137 * Chip select configuration
138 */
139/* NOR Flash 0 on CS0 */
140#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
141 BR_PS_16 | \
142 BR_V)
143#define CONFIG_SYS_OR0_PRELIM (OR_AM_64MB | \
144 OR_GPCM_ACS_DIV4 | \
145 OR_GPCM_SCY_8)
146
147/* NOR Flash 1 on CS1 */
148#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \
149 BR_PS_16 | \
150 BR_V)
151#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
152
153/* NAND flash on CS2 */
154#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \
155 BR_PS_8 | \
156 BR_V)
157
158/* NAND flash on CS2 */
159#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \
160 OR_GPCM_BCTLD | \
161 OR_GPCM_CSNT | \
162 OR_GPCM_ACS_DIV4 | \
163 OR_GPCM_SCY_4 | \
164 OR_GPCM_TRLX | \
165 OR_GPCM_EHTR)
166
167/* NAND flash on CS3 */
168#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \
169 BR_PS_8 | \
170 BR_V)
171#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
172
173/*
174 * Use L1 as initial stack
175 */
176#define CONFIG_SYS_INIT_RAM_LOCK 1
177#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
178#define CONFIG_SYS_INIT_RAM_END 0x4000
179
180#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
181#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
182#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
183
184#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
185#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
186
187/*
188 * Serial Port
189 */
190#define CONFIG_CONS_INDEX 1
191#define CONFIG_SYS_NS16550
192#define CONFIG_SYS_NS16550_SERIAL
193#define CONFIG_SYS_NS16550_REG_SIZE 1
194#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
195#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
196#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
197#define CONFIG_SYS_BAUDRATE_TABLE \
198 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
199#define CONFIG_BAUDRATE 115200
200#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
201#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
202
203/*
204 * Use the HUSH parser
205 */
206#define CONFIG_SYS_HUSH_PARSER
207#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
208
209/*
210 * Pass open firmware flat tree
211 */
212#define CONFIG_OF_LIBFDT 1
213#define CONFIG_OF_BOARD_SETUP 1
214#define CONFIG_OF_STDOUT_VIA_ALIAS 1
215
216#define CONFIG_SYS_64BIT_VSPRINTF 1
217#define CONFIG_SYS_64BIT_STRTOUL 1
218
219/*
220 * I2C
221 */
222#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
223#define CONFIG_HARD_I2C /* I2C with hardware support */
224#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
225#define CONFIG_SYS_I2C_SLAVE 0x7F
226#define CONFIG_SYS_I2C_OFFSET 0x3000
227#define CONFIG_SYS_I2C2_OFFSET 0x3100
228#define CONFIG_I2C_MULTI_BUS
229#define CONFIG_I2C_CMD_TREE
230
231/* I2C EEPROM */
232#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
233#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
234#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
235#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
236
237/* I2C RTC */
238#define CONFIG_RTC_M41T11 1
239#define CONFIG_SYS_I2C_RTC_ADDR 0x68
240#define CONFIG_SYS_M41T11_BASE_YEAR 2000
241
242/* GPIO */
243#define CONFIG_PCA953X
244#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
245#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x19
246#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
247
248/* PCA957 @ 0x18 */
249#define CONFIG_SYS_PCA953X_BRD_CFG0 0x01
250#define CONFIG_SYS_PCA953X_BRD_CFG1 0x02
251#define CONFIG_SYS_PCA953X_BRD_CFG2 0x04
252#define CONFIG_SYS_PCA953X_XMC_ROOT0 0x08
253#define CONFIG_SYS_PCA953X_FLASH_PASS_CS 0x10
254#define CONFIG_SYS_PCA953X_FLASH_WP 0x20
255#define CONFIG_SYS_PCA953X_MONARCH 0x40
256#define CONFIG_SYS_PCA953X_EREADY 0x80
257
258/* PCA957 @ 0x19 */
259#define CONFIG_SYS_PCA953X_P14_IO0 0x01
260#define CONFIG_SYS_PCA953X_P14_IO1 0x02
261#define CONFIG_SYS_PCA953X_P14_IO2 0x04
262#define CONFIG_SYS_PCA953X_P14_IO3 0x08
263#define CONFIG_SYS_PCA953X_P14_IO4 0x10
264#define CONFIG_SYS_PCA953X_P14_IO5 0x20
265#define CONFIG_SYS_PCA953X_P14_IO6 0x40
266#define CONFIG_SYS_PCA953X_P14_IO7 0x80
267
268/*
269 * General PCI
270 * Memory space is mapped 1-1, but I/O space must start from 0.
271 */
272#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
273#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
274#define CONFIG_SYS_PCI1_MEM_SIZE 0x40000000 /* 1G */
275#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
276#define CONFIG_SYS_PCI1_IO_PHYS 0xe8000000
277#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 1M */
278
279/*
280 * Networking options
281 */
282#define CONFIG_TSEC_ENET /* tsec ethernet support */
283#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
284#define CONFIG_NET_MULTI 1
285#define CONFIG_MII 1 /* MII PHY management */
286#define CONFIG_ETHPRIME "eTSEC1"
287
288#define CONFIG_TSEC1 1
289#define CONFIG_TSEC1_NAME "eTSEC1"
290#define TSEC1_FLAGS TSEC_GIGABIT
291#define TSEC1_PHY_ADDR 1
292#define TSEC1_PHYIDX 0
293#define CONFIG_HAS_ETH0
294
295#define CONFIG_TSEC2 1
296#define CONFIG_TSEC2_NAME "eTSEC2"
297#define TSEC2_FLAGS TSEC_GIGABIT
298#define TSEC2_PHY_ADDR 2
299#define TSEC2_PHYIDX 0
300#define CONFIG_HAS_ETH1
301
302#define CONFIG_TSEC3 1
303#define CONFIG_TSEC3_NAME "eTSEC3"
304#define TSEC3_FLAGS TSEC_GIGABIT
305#define TSEC3_PHY_ADDR 3
306#define TSEC3_PHYIDX 0
307#define CONFIG_HAS_ETH2
308
309#define CONFIG_TSEC4 1
310#define CONFIG_TSEC4_NAME "eTSEC4"
311#define TSEC4_FLAGS TSEC_GIGABIT
312#define TSEC4_PHY_ADDR 4
313#define TSEC4_PHYIDX 0
314#define CONFIG_HAS_ETH3
315
316/*
317 * BOOTP options
318 */
319#define CONFIG_BOOTP_BOOTFILESIZE
320#define CONFIG_BOOTP_BOOTPATH
321#define CONFIG_BOOTP_GATEWAY
322
323/*
324 * Command configuration.
325 */
326#include <config_cmd_default.h>
327
328#define CONFIG_CMD_ASKENV
329#define CONFIG_CMD_DATE
330#define CONFIG_CMD_DHCP
331#define CONFIG_CMD_EEPROM
332#define CONFIG_CMD_ELF
333#define CONFIG_CMD_ENV
334#define CONFIG_CMD_FLASH
335#define CONFIG_CMD_I2C
336#define CONFIG_CMD_JFFS2
337#define CONFIG_CMD_MII
338#define CONFIG_CMD_NAND
339#define CONFIG_CMD_NET
340#define CONFIG_CMD_PCA953X
341#define CONFIG_CMD_PCA953X_INFO
342#define CONFIG_CMD_PCI
343#define CONFIG_CMD_PING
344#define CONFIG_CMD_SNTP
345
346/*
347 * Miscellaneous configurable options
348 */
349#define CONFIG_SYS_LONGHELP /* undef to save memory */
350#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
351#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
352#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
353#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
354#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
355#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
356#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
357#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
358#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
359#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */
360#define CONFIG_PANIC_HANG /* do not reset board on panic */
361#define CONFIG_PREBOOT /* enable preboot variable */
362#define CONFIG_FIT 1
363#define CONFIG_FIT_VERBOSE 1
364#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
365#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
366
367/*
368 * For booting Linux, the board info and command line data
369 * have to be in the first 16 MB of memory, since this is
370 * the maximum mapped by the Linux kernel during initialization.
371 */
372#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
373
374/*
375 * Boot Flags
376 */
377#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
378#define BOOTFLAG_WARM 0x02 /* Software reboot */
379
380/*
381 * Environment Configuration
382 */
383#define CONFIG_ENV_IS_IN_FLASH 1
384#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
385#define CONFIG_ENV_SIZE 0x8000
386#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
387
388/*
389 * Flash memory map:
390 * fff80000 - ffffffff Pri U-Boot (512 KB)
391 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
392 * fff00000 - fff3ffff Pri FDT (256KB)
393 * fef00000 - ffefffff Pri OS image (16MB)
394 * fc000000 - feefffff Pri OS Use/Filesystem (47MB)
395 *
396 * fbf80000 - fbffffff Sec U-Boot (512 KB)
397 * fbf40000 - fbf7ffff Sec U-Boot Environment (256 KB)
398 * fbf00000 - fbf3ffff Sec FDT (256KB)
399 * faf00000 - fbefffff Sec OS image (16MB)
400 * f8000000 - faefffff Sec OS Use/Filesystem (47MB)
401 */
402#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000)
403#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xfbf80000)
404#define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000)
405#define CONFIG_FDT2_ENV_ADDR MK_STR(0xfbf00000)
406#define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000)
407#define CONFIG_OS2_ENV_ADDR MK_STR(0xfaf00000)
408
409#define CONFIG_PROG_UBOOT1 \
410 "$download_cmd $loadaddr $ubootfile; " \
411 "if test $? -eq 0; then " \
412 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
413 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
414 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
415 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
416 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
417 "if test $? -ne 0; then " \
418 "echo PROGRAM FAILED; " \
419 "else; " \
420 "echo PROGRAM SUCCEEDED; " \
421 "fi; " \
422 "else; " \
423 "echo DOWNLOAD FAILED; " \
424 "fi;"
425
426#define CONFIG_PROG_UBOOT2 \
427 "$download_cmd $loadaddr $ubootfile; " \
428 "if test $? -eq 0; then " \
429 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
430 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
431 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
432 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
433 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
434 "if test $? -ne 0; then " \
435 "echo PROGRAM FAILED; " \
436 "else; " \
437 "echo PROGRAM SUCCEEDED; " \
438 "fi; " \
439 "else; " \
440 "echo DOWNLOAD FAILED; " \
441 "fi;"
442
443#define CONFIG_BOOT_OS_NET \
444 "$download_cmd $osaddr $osfile; " \
445 "if test $? -eq 0; then " \
446 "if test -n $fdtaddr; then " \
447 "$download_cmd $fdtaddr $fdtfile; " \
448 "if test $? -eq 0; then " \
449 "bootm $osaddr - $fdtaddr; " \
450 "else; " \
451 "echo FDT DOWNLOAD FAILED; " \
452 "fi; " \
453 "else; " \
454 "bootm $osaddr; " \
455 "fi; " \
456 "else; " \
457 "echo OS DOWNLOAD FAILED; " \
458 "fi;"
459
460#define CONFIG_PROG_OS1 \
461 "$download_cmd $osaddr $osfile; " \
462 "if test $? -eq 0; then " \
463 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
464 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
465 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
466 "if test $? -ne 0; then " \
467 "echo OS PROGRAM FAILED; " \
468 "else; " \
469 "echo OS PROGRAM SUCCEEDED; " \
470 "fi; " \
471 "else; " \
472 "echo OS DOWNLOAD FAILED; " \
473 "fi;"
474
475#define CONFIG_PROG_OS2 \
476 "$download_cmd $osaddr $osfile; " \
477 "if test $? -eq 0; then " \
478 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
479 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
480 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
481 "if test $? -ne 0; then " \
482 "echo OS PROGRAM FAILED; " \
483 "else; " \
484 "echo OS PROGRAM SUCCEEDED; " \
485 "fi; " \
486 "else; " \
487 "echo OS DOWNLOAD FAILED; " \
488 "fi;"
489
490#define CONFIG_PROG_FDT1 \
491 "$download_cmd $fdtaddr $fdtfile; " \
492 "if test $? -eq 0; then " \
493 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
494 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
495 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
496 "if test $? -ne 0; then " \
497 "echo FDT PROGRAM FAILED; " \
498 "else; " \
499 "echo FDT PROGRAM SUCCEEDED; " \
500 "fi; " \
501 "else; " \
502 "echo FDT DOWNLOAD FAILED; " \
503 "fi;"
504
505#define CONFIG_PROG_FDT2 \
506 "$download_cmd $fdtaddr $fdtfile; " \
507 "if test $? -eq 0; then " \
508 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
509 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
510 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
511 "if test $? -ne 0; then " \
512 "echo FDT PROGRAM FAILED; " \
513 "else; " \
514 "echo FDT PROGRAM SUCCEEDED; " \
515 "fi; " \
516 "else; " \
517 "echo FDT DOWNLOAD FAILED; " \
518 "fi;"
519
520#define CONFIG_EXTRA_ENV_SETTINGS \
521 "autoload=yes\0" \
522 "download_cmd=tftp\0" \
523 "console_args=console=ttyS0,115200\0" \
524 "root_args=root=/dev/nfs rw\0" \
525 "misc_args=ip=on\0" \
526 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
527 "bootfile=/home/user/file\0" \
528 "osfile=/home/user/uImage-XPedite5200\0" \
529 "fdtfile=/home/user/xpedite5200.dtb\0" \
530 "ubootfile=/home/user/u-boot.bin\0" \
531 "fdtaddr=c00000\0" \
532 "osaddr=0x1000000\0" \
533 "loadaddr=0x1000000\0" \
534 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
535 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
536 "prog_os1="CONFIG_PROG_OS1"\0" \
537 "prog_os2="CONFIG_PROG_OS2"\0" \
538 "prog_fdt1="CONFIG_PROG_FDT1"\0" \
539 "prog_fdt2="CONFIG_PROG_FDT2"\0" \
540 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
541 "bootcmd_flash1=run set_bootargs; " \
542 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
543 "bootcmd_flash2=run set_bootargs; " \
544 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
545 "bootcmd=run bootcmd_flash1\0"
546#endif /* __CONFIG_H */