blob: da89a36b96ad58b23aacf68f3c9f85c123dd95f6 [file] [log] [blame]
Prabhakar Kushwaha7d436072013-09-12 11:11:28 +05301/*
2 * Copyright 2013 Freescale Semiconductor, Inc.
3 *
4 * SPDX-License-Identifier: GPL-2.0+
5 */
6
7#include <common.h>
8#include <i2c.h>
9#include <hwconfig.h>
10#include <asm/mmu.h>
York Sun5614e712013-09-30 09:22:09 -070011#include <fsl_ddr_sdram.h>
12#include <fsl_ddr_dimm_params.h>
Prabhakar Kushwaha7d436072013-09-12 11:11:28 +053013#include <asm/fsl_law.h>
14#include "ddr.h"
15
16DECLARE_GLOBAL_DATA_PTR;
17
18void fsl_ddr_board_options(memctl_options_t *popts,
19 dimm_params_t *pdimm,
20 unsigned int ctrl_num)
21{
22 const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
23 ulong ddr_freq;
24
25 if (ctrl_num > 2) {
26 printf("Not supported controller number %d\n", ctrl_num);
27 return;
28 }
29 if (!pdimm->n_ranks)
30 return;
31
32 pbsp = udimms[0];
33
34 /* Get clk_adjust, cpo, write_data_delay,2t, according to the board ddr
35 * freqency and n_banks specified in board_specific_parameters table.
36 */
37 ddr_freq = get_ddr_freq(0) / 1000000;
38 while (pbsp->datarate_mhz_high) {
39 if (pbsp->n_ranks == pdimm->n_ranks &&
40 (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
41 if (ddr_freq <= pbsp->datarate_mhz_high) {
42 popts->cpo_override = pbsp->cpo;
43 popts->write_data_delay =
44 pbsp->write_data_delay;
45 popts->clk_adjust = pbsp->clk_adjust;
46 popts->wrlvl_start = pbsp->wrlvl_start;
47 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
48 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
49 popts->twot_en = pbsp->force_2t;
50 goto found;
51 }
52 pbsp_highest = pbsp;
53 }
54 pbsp++;
55 }
56
57 if (pbsp_highest) {
58 printf("Error: board specific timing not found\n");
59 printf("for data rate %lu MT/s\n", ddr_freq);
60 printf("Trying to use the highest speed (%u) parameters\n",
61 pbsp_highest->datarate_mhz_high);
62 popts->cpo_override = pbsp_highest->cpo;
63 popts->write_data_delay = pbsp_highest->write_data_delay;
64 popts->clk_adjust = pbsp_highest->clk_adjust;
65 popts->wrlvl_start = pbsp_highest->wrlvl_start;
66 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
67 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
68 popts->twot_en = pbsp_highest->force_2t;
69 } else {
70 panic("DIMM is not supported by this board");
71 }
72found:
73 debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
74 "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
75 "wrlvl_ctrl_3 0x%x\n",
76 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
77 pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
78 pbsp->wrlvl_ctl_3);
79
80 /*
81 * Factors to consider for half-strength driver enable:
82 * - number of DIMMs installed
83 */
84 popts->half_strength_driver_enable = 0;
85 /*
86 * Write leveling override
87 */
88 popts->wrlvl_override = 1;
89 popts->wrlvl_sample = 0xf;
90
91 /*
92 * rtt and rtt_wr override
93 */
94 popts->rtt_override = 0;
95
96 /* Enable ZQ calibration */
97 popts->zq_en = 1;
98
99 /* DHC_EN =1, ODT = 75 Ohm */
100 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
101 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
102}
103
104phys_size_t initdram(int board_type)
105{
106 phys_size_t dram_size;
107
108 puts("Initializing....using SPD\n");
109
110 dram_size = fsl_ddr_sdram();
111
112 dram_size = setup_ddr_tlbs(dram_size / 0x100000);
113 dram_size *= 0x100000;
114
115 puts(" DDR: ");
116 return dram_size;
117}