board/engicam/isiotmx6ul/isiotmx6ul.c

/*
 * Copyright (C) 2016 Amarula Solutions B.V.
 * Copyright (C) 2016 Engicam S.r.l.
 * Author: Jagan Teki <jagan@amarulasolutions.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>

#include <asm/io.h>
#include <asm/gpio.h>
#include <linux/sizes.h>

#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/imx-common/iomux-v3.h>

DECLARE_GLOBAL_DATA_PTR;

#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE | \
			PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
			PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

static iomux_v3_cfg_t const uart1_pads[] = {
	MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
	MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
};

int board_early_init_f(void)
{
	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));

	return 0;
}

#ifdef CONFIG_NAND_MXS

#define GPMI_PAD_CTRL0		(PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
#define GPMI_PAD_CTRL1		(PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
				PAD_CTL_SRE_FAST)
#define GPMI_PAD_CTRL2		(GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)

static iomux_v3_cfg_t const nand_pads[] = {
	MX6_PAD_NAND_DATA00__RAWNAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_DATA01__RAWNAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_DATA02__RAWNAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_DATA03__RAWNAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_DATA04__RAWNAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_DATA05__RAWNAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_DATA06__RAWNAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_DATA07__RAWNAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_CLE__RAWNAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_ALE__RAWNAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_RE_B__RAWNAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_WE_B__RAWNAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NAND_READY_B__RAWNAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
};

static void setup_gpmi_nand(void)
{
	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;

	/* config gpmi nand iomux */
	imx_iomux_v3_setup_multiple_pads(nand_pads, ARRAY_SIZE(nand_pads));

	clrbits_le32(&mxc_ccm->CCGR4,
		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);

	/*
	 * config gpmi and bch clock to 100 MHz
	 * bch/gpmi select PLL2 PFD2 400M
	 * 100M = 400M / 4
	 */
	clrbits_le32(&mxc_ccm->cscmr1,
		     MXC_CCM_CSCMR1_BCH_CLK_SEL |
		     MXC_CCM_CSCMR1_GPMI_CLK_SEL);
	clrsetbits_le32(&mxc_ccm->cscdr1,
			MXC_CCM_CSCDR1_BCH_PODF_MASK |
			MXC_CCM_CSCDR1_GPMI_PODF_MASK,
			(3 << MXC_CCM_CSCDR1_BCH_PODF_OFFSET) |
			(3 << MXC_CCM_CSCDR1_GPMI_PODF_OFFSET));

	/* enable gpmi and bch clock gating */
	setbits_le32(&mxc_ccm->CCGR4,
		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);

	/* enable apbh clock gating */
	setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
}
#endif /* CONFIG_NAND_MXS */

int board_init(void)
{
	/* Address of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

#ifdef CONFIG_NAND_MXS
	setup_gpmi_nand();
#endif
	return 0;
}

int dram_init(void)
{
	gd->ram_size = imx_ddr_size();

	return 0;
}

#ifdef CONFIG_SPL_BUILD
#include <libfdt.h>
#include <spl.h>

#include <asm/arch/crm_regs.h>
#include <asm/arch/mx6-ddr.h>

/* MMC board initialization is needed till adding DM support in SPL */
#if defined(CONFIG_FSL_ESDHC) && !defined(CONFIG_DM_MMC)
#include <mmc.h>
#include <fsl_esdhc.h>

#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |             \
	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |               \
	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

static iomux_v3_cfg_t const usdhc1_pads[] = {
	MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),

	/* VSELECT */
	MX6_PAD_GPIO1_IO05__USDHC1_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	/* CD */
	MX6_PAD_UART1_RTS_B__GPIO1_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
	/* RST_B */
	MX6_PAD_GPIO1_IO09__GPIO1_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
};

#define USDHC1_CD_GPIO	IMX_GPIO_NR(1, 19)

struct fsl_esdhc_cfg usdhc_cfg[1] = {
	{USDHC1_BASE_ADDR, 0, 4},
};

int board_mmc_getcd(struct mmc *mmc)
{
	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
	int ret = 0;

	switch (cfg->esdhc_base) {
	case USDHC1_BASE_ADDR:
		ret = !gpio_get_value(USDHC1_CD_GPIO);
		break;
	}

	return ret;
}

int board_mmc_init(bd_t *bis)
{
	int i, ret;

	/*
	* According to the board_mmc_init() the following map is done:
	* (U-boot device node)    (Physical Port)
	* mmc0				USDHC1
	*/
	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
		switch (i) {
		case 0:
			imx_iomux_v3_setup_multiple_pads(
				usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
			gpio_direction_input(USDHC1_CD_GPIO);
			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
			break;
		default:
			printf("Warning - USDHC%d controller not supporting\n",
			       i + 1);
			return 0;
		}

		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
		if (ret) {
			printf("Warning: failed to initialize mmc dev %d\n", i);
			return ret;
		}
	}

	return 0;
}
#endif /* CONFIG_FSL_ESDHC */

static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
	.grp_addds = 0x00000030,
	.grp_ddrmode_ctl = 0x00020000,
	.grp_b0ds = 0x00000030,
	.grp_ctlds = 0x00000030,
	.grp_b1ds = 0x00000030,
	.grp_ddrpke = 0x00000000,
	.grp_ddrmode = 0x00020000,
	.grp_ddr_type = 0x000c0000,
};

static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
	.dram_dqm0 = 0x00000030,
	.dram_dqm1 = 0x00000030,
	.dram_ras = 0x00000030,
	.dram_cas = 0x00000030,
	.dram_odt0 = 0x00000030,
	.dram_odt1 = 0x00000030,
	.dram_sdba2 = 0x00000000,
	.dram_sdclk_0 = 0x00000008,
	.dram_sdqs0 = 0x00000038,
	.dram_sdqs1 = 0x00000030,
	.dram_reset = 0x00000030,
};

static struct mx6_mmdc_calibration mx6_mmcd_calib = {
	.p0_mpwldectrl0 = 0x00070007,
	.p0_mpdgctrl0 = 0x41490145,
	.p0_mprddlctl = 0x40404546,
	.p0_mpwrdlctl = 0x4040524D,
};

struct mx6_ddr_sysinfo ddr_sysinfo = {
	.dsize = 0,
	.cs_density = 20,
	.ncs = 1,
	.cs1_mirror = 0,
	.rtt_wr = 2,
	.rtt_nom = 1,		/* RTT_Nom = RZQ/2 */
	.walat = 1,		/* Write additional latency */
	.ralat = 5,		/* Read additional latency */
	.mif3_mode = 3,		/* Command prediction working mode */
	.bi_on = 1,		/* Bank interleaving enabled */
	.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
	.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
	.ddr_type = DDR_TYPE_DDR3,
};

static struct mx6_ddr3_cfg mem_ddr = {
	.mem_speed = 800,
	.density = 4,
	.width = 16,
	.banks = 8,
	.rowaddr = 15,
	.coladdr = 10,
	.pagesz = 2,
	.trcd = 1375,
	.trcmin = 4875,
	.trasmin = 3500,
};

static void ccgr_init(void)
{
	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;

	writel(0x00c03f3f, &ccm->CCGR0);
	writel(0xfcffff00, &ccm->CCGR1);
	writel(0x0cffffcc, &ccm->CCGR2);
	writel(0x3f3c3030, &ccm->CCGR3);
	writel(0xff00fffc, &ccm->CCGR4);
	writel(0x033f30ff, &ccm->CCGR5);
	writel(0x00c00fff, &ccm->CCGR6);
}

static void spl_dram_init(void)
{
	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
}

void board_init_f(ulong dummy)
{
	/* setup AIPS and disable watchdog */
	arch_cpu_init();

	ccgr_init();

	/* iomux and setup of i2c */
	board_early_init_f();

	/* setup GP timer */
	timer_init();

	/* UART clocks enabled and gd valid - init serial console */
	preloader_console_init();

	/* DDR initialization */
	spl_dram_init();

	/* Clear the BSS. */
	memset(__bss_start, 0, __bss_end - __bss_start);

	/* load/boot image from boot device */
	board_init_r(NULL, 0);
}
#endif /* CONFIG_SPL_BUILD */