| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame] | 1 | // SPDX-License-Identifier: BSD-3-Clause |
| 2 | /* Copyright (c) 2022, The Linux Foundation. All rights reserved. */ |
| 3 | |
| 4 | #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| 5 | #include <dt-bindings/interrupt-controller/irq.h> |
| 6 | #include <dt-bindings/input/linux-event-codes.h> |
| 7 | #include <dt-bindings/spmi/spmi.h> |
| 8 | |
| 9 | / { |
| 10 | thermal-zones { |
| 11 | pm8953-thermal { |
| 12 | polling-delay-passive = <0>; |
| 13 | polling-delay = <0>; |
| 14 | |
| 15 | thermal-sensors = <&pm8953_temp>; |
| 16 | |
| 17 | trips { |
| 18 | trip0 { |
| 19 | temperature = <105000>; |
| 20 | hysteresis = <0>; |
| 21 | type = "passive"; |
| 22 | }; |
| 23 | |
| 24 | trip1 { |
| 25 | temperature = <125000>; |
| 26 | hysteresis = <0>; |
| 27 | type = "hot"; |
| 28 | }; |
| 29 | |
| 30 | trip2 { |
| 31 | temperature = <145000>; |
| 32 | hysteresis = <0>; |
| 33 | type = "critical"; |
| 34 | }; |
| 35 | }; |
| 36 | }; |
| 37 | }; |
| 38 | }; |
| 39 | |
| 40 | &spmi_bus { |
| 41 | pmic@0 { |
| 42 | compatible = "qcom,pm8953", "qcom,spmi-pmic"; |
| 43 | reg = <0 SPMI_USID>; |
| 44 | #address-cells = <1>; |
| 45 | #size-cells = <0>; |
| 46 | |
| 47 | pm8953_pon: pon@800 { |
| 48 | compatible = "qcom,pm8916-pon"; |
| 49 | reg = <0x800>; |
| 50 | mode-bootloader = <0x2>; |
| 51 | mode-recovery = <0x1>; |
| 52 | |
| 53 | pwrkey { |
| 54 | compatible = "qcom,pm8941-pwrkey"; |
| 55 | interrupts = <0x00 0x08 0 IRQ_TYPE_EDGE_BOTH>; |
| 56 | debounce = <15625>; |
| 57 | bias-pull-up; |
| 58 | linux,code = <KEY_POWER>; |
| 59 | }; |
| 60 | |
| 61 | pm8953_resin: resin { |
| 62 | compatible = "qcom,pm8941-resin"; |
| 63 | interrupts = <0x00 0x08 1 IRQ_TYPE_EDGE_BOTH>; |
| 64 | debounce = <15625>; |
| 65 | bias-pull-up; |
| 66 | status = "disabled"; |
| 67 | }; |
| 68 | }; |
| 69 | |
| 70 | pm8953_temp: temp-alarm@2400 { |
| 71 | compatible = "qcom,spmi-temp-alarm"; |
| 72 | reg = <0x2400>; |
| 73 | interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; |
| 74 | io-channels = <&pm8953_vadc VADC_DIE_TEMP>; |
| 75 | io-channel-names = "thermal"; |
| 76 | #thermal-sensor-cells = <0>; |
| 77 | }; |
| 78 | |
| 79 | pm8953_vadc: adc@3100 { |
| 80 | compatible = "qcom,spmi-vadc"; |
| 81 | reg = <0x3100>; |
| 82 | interrupts = <0x00 0x31 0x00 0x01>; |
| 83 | #address-cells = <1>; |
| 84 | #size-cells = <0>; |
| 85 | #io-channel-cells = <1>; |
| 86 | |
| 87 | channel@8 { |
| 88 | reg = <VADC_DIE_TEMP>; |
| 89 | }; |
| 90 | channel@9 { |
| 91 | reg = <VADC_REF_625MV>; |
| 92 | }; |
| 93 | channel@a { |
| 94 | reg = <VADC_REF_1250MV>; |
| 95 | }; |
| 96 | channel@c { |
| 97 | reg = <VADC_SPARE1>; |
| 98 | }; |
| 99 | channel@e { |
| 100 | reg = <VADC_GND_REF>; |
| 101 | }; |
| 102 | channel@f { |
| 103 | reg = <VADC_VDD_VADC>; |
| 104 | }; |
| 105 | }; |
| 106 | |
| 107 | rtc@6000 { |
| 108 | compatible = "qcom,pm8941-rtc"; |
| 109 | reg = <0x6000>, <0x6100>; |
| 110 | reg-names = "rtc", "alarm"; |
| 111 | interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; |
| 112 | }; |
| 113 | |
| 114 | pm8953_gpios: gpio@c000 { |
| 115 | compatible = "qcom,pm8953-gpio", "qcom,spmi-gpio"; |
| 116 | reg = <0xc000>; |
| 117 | gpio-controller; |
| 118 | gpio-ranges = <&pm8953_gpios 0 0 8>; |
| 119 | #gpio-cells = <2>; |
| 120 | interrupt-controller; |
| 121 | #interrupt-cells = <2>; |
| 122 | }; |
| 123 | }; |
| 124 | |
| 125 | pmic@1 { |
| 126 | compatible = "qcom,pm8953", "qcom,spmi-pmic"; |
| 127 | reg = <1 SPMI_USID>; |
| 128 | #address-cells = <1>; |
| 129 | #size-cells = <0>; |
| 130 | }; |
| 131 | }; |