| /** @file | |
| This file provides control over block-oriented firmware devices. | |
| Copyright (c) 2006 - 2011, Intel Corporation. All rights reserved.<BR> | |
| This program and the accompanying materials are licensed and made available under | |
| the terms and conditions of the BSD License that accompanies this distribution. | |
| The full text of the license may be found at | |
| http://opensource.org/licenses/bsd-license.php. | |
| THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, | |
| WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. | |
| @par Revision Reference: PI | |
| Version 1.0 and 1.2. | |
| **/ | |
| #ifndef __FIRMWARE_VOLUME_BLOCK_H__ | |
| #define __FIRMWARE_VOLUME_BLOCK_H__ | |
| // | |
| // EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL is defined in PI 1.0 spec and its GUID value | |
| // is later updated to be the same as that of EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL | |
| // defined in PI 1.2 spec. | |
| // | |
| #define EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL_GUID \ | |
| { 0x8f644fa9, 0xe850, 0x4db1, {0x9c, 0xe2, 0xb, 0x44, 0x69, 0x8e, 0x8d, 0xa4 } } | |
| #define EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL_GUID \ | |
| { 0x8f644fa9, 0xe850, 0x4db1, {0x9c, 0xe2, 0xb, 0x44, 0x69, 0x8e, 0x8d, 0xa4 } } | |
| typedef struct _EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL; | |
| typedef EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL; | |
| /** | |
| The GetAttributes() function retrieves the attributes and | |
| current settings of the block. | |
| @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance. | |
| @param Attributes Pointer to EFI_FVB_ATTRIBUTES_2 in which the | |
| attributes and current settings are | |
| returned. Type EFI_FVB_ATTRIBUTES_2 is defined | |
| in EFI_FIRMWARE_VOLUME_HEADER. | |
| @retval EFI_SUCCESS The firmware volume attributes were | |
| returned. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI * EFI_FVB_GET_ATTRIBUTES)( | |
| IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This, | |
| OUT EFI_FVB_ATTRIBUTES_2 *Attributes | |
| ); | |
| /** | |
| The SetAttributes() function sets configurable firmware volume | |
| attributes and returns the new settings of the firmware volume. | |
| @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance. | |
| @param Attributes On input, Attributes is a pointer to | |
| EFI_FVB_ATTRIBUTES_2 that contains the | |
| desired firmware volume settings. On | |
| successful return, it contains the new | |
| settings of the firmware volume. Type | |
| EFI_FVB_ATTRIBUTES_2 is defined in | |
| EFI_FIRMWARE_VOLUME_HEADER. | |
| @retval EFI_SUCCESS The firmware volume attributes were returned. | |
| @retval EFI_INVALID_PARAMETER The attributes requested are in | |
| conflict with the capabilities | |
| as declared in the firmware | |
| volume header. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI * EFI_FVB_SET_ATTRIBUTES)( | |
| IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This, | |
| IN OUT EFI_FVB_ATTRIBUTES_2 *Attributes | |
| ); | |
| /** | |
| The GetPhysicalAddress() function retrieves the base address of | |
| a memory-mapped firmware volume. This function should be called | |
| only for memory-mapped firmware volumes. | |
| @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance. | |
| @param Address Pointer to a caller-allocated | |
| EFI_PHYSICAL_ADDRESS that, on successful | |
| return from GetPhysicalAddress(), contains the | |
| base address of the firmware volume. | |
| @retval EFI_SUCCESS The firmware volume base address was returned. | |
| @retval EFI_UNSUPPORTED The firmware volume is not memory mapped. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI * EFI_FVB_GET_PHYSICAL_ADDRESS)( | |
| IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This, | |
| OUT EFI_PHYSICAL_ADDRESS *Address | |
| ); | |
| /** | |
| The GetBlockSize() function retrieves the size of the requested | |
| block. It also returns the number of additional blocks with | |
| the identical size. The GetBlockSize() function is used to | |
| retrieve the block map (see EFI_FIRMWARE_VOLUME_HEADER). | |
| @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance. | |
| @param Lba Indicates the block for which to return the size. | |
| @param BlockSize Pointer to a caller-allocated UINTN in which | |
| the size of the block is returned. | |
| @param NumberOfBlocks Pointer to a caller-allocated UINTN in | |
| which the number of consecutive blocks, | |
| starting with Lba, is returned. All | |
| blocks in this range have a size of | |
| BlockSize. | |
| @retval EFI_SUCCESS The firmware volume base address was returned. | |
| @retval EFI_INVALID_PARAMETER The requested LBA is out of range. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI * EFI_FVB_GET_BLOCK_SIZE)( | |
| IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This, | |
| IN EFI_LBA Lba, | |
| OUT UINTN *BlockSize, | |
| OUT UINTN *NumberOfBlocks | |
| ); | |
| /** | |
| Reads the specified number of bytes into a buffer from the specified block. | |
| The Read() function reads the requested number of bytes from the | |
| requested block and stores them in the provided buffer. | |
| Implementations should be mindful that the firmware volume | |
| might be in the ReadDisabled state. If it is in this state, | |
| the Read() function must return the status code | |
| EFI_ACCESS_DENIED without modifying the contents of the | |
| buffer. The Read() function must also prevent spanning block | |
| boundaries. If a read is requested that would span a block | |
| boundary, the read must read up to the boundary but not | |
| beyond. The output parameter NumBytes must be set to correctly | |
| indicate the number of bytes actually read. The caller must be | |
| aware that a read may be partially completed. | |
| @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance. | |
| @param Lba The starting logical block index | |
| from which to read. | |
| @param Offset Offset into the block at which to begin reading. | |
| @param NumBytes Pointer to a UINTN. At entry, *NumBytes | |
| contains the total size of the buffer. At | |
| exit, *NumBytes contains the total number of | |
| bytes read. | |
| @param Buffer Pointer to a caller-allocated buffer that will | |
| be used to hold the data that is read. | |
| @retval EFI_SUCCESS The firmware volume was read successfully, | |
| and contents are in Buffer. | |
| @retval EFI_BAD_BUFFER_SIZE Read attempted across an LBA | |
| boundary. On output, NumBytes | |
| contains the total number of bytes | |
| returned in Buffer. | |
| @retval EFI_ACCESS_DENIED The firmware volume is in the | |
| ReadDisabled state. | |
| @retval EFI_DEVICE_ERROR The block device is not | |
| functioning correctly and could | |
| not be read. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_FVB_READ)( | |
| IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This, | |
| IN EFI_LBA Lba, | |
| IN UINTN Offset, | |
| IN OUT UINTN *NumBytes, | |
| IN OUT UINT8 *Buffer | |
| ); | |
| /** | |
| Writes the specified number of bytes from the input buffer to the block. | |
| The Write() function writes the specified number of bytes from | |
| the provided buffer to the specified block and offset. If the | |
| firmware volume is sticky write, the caller must ensure that | |
| all the bits of the specified range to write are in the | |
| EFI_FVB_ERASE_POLARITY state before calling the Write() | |
| function, or else the result will be unpredictable. This | |
| unpredictability arises because, for a sticky-write firmware | |
| volume, a write may negate a bit in the EFI_FVB_ERASE_POLARITY | |
| state but cannot flip it back again. Before calling the | |
| Write() function, it is recommended for the caller to first call | |
| the EraseBlocks() function to erase the specified block to | |
| write. A block erase cycle will transition bits from the | |
| (NOT)EFI_FVB_ERASE_POLARITY state back to the | |
| EFI_FVB_ERASE_POLARITY state. Implementations should be | |
| mindful that the firmware volume might be in the WriteDisabled | |
| state. If it is in this state, the Write() function must | |
| return the status code EFI_ACCESS_DENIED without modifying the | |
| contents of the firmware volume. The Write() function must | |
| also prevent spanning block boundaries. If a write is | |
| requested that spans a block boundary, the write must store up | |
| to the boundary but not beyond. The output parameter NumBytes | |
| must be set to correctly indicate the number of bytes actually | |
| written. The caller must be aware that a write may be | |
| partially completed. All writes, partial or otherwise, must be | |
| fully flushed to the hardware before the Write() service | |
| returns. | |
| @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance. | |
| @param Lba The starting logical block index to write to. | |
| @param Offset Offset into the block at which to begin writing. | |
| @param NumBytes The pointer to a UINTN. At entry, *NumBytes | |
| contains the total size of the buffer. At | |
| exit, *NumBytes contains the total number of | |
| bytes actually written. | |
| @param Buffer The pointer to a caller-allocated buffer that | |
| contains the source for the write. | |
| @retval EFI_SUCCESS The firmware volume was written successfully. | |
| @retval EFI_BAD_BUFFER_SIZE The write was attempted across an | |
| LBA boundary. On output, NumBytes | |
| contains the total number of bytes | |
| actually written. | |
| @retval EFI_ACCESS_DENIED The firmware volume is in the | |
| WriteDisabled state. | |
| @retval EFI_DEVICE_ERROR The block device is malfunctioning | |
| and could not be written. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI * EFI_FVB_WRITE)( | |
| IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This, | |
| IN EFI_LBA Lba, | |
| IN UINTN Offset, | |
| IN OUT UINTN *NumBytes, | |
| IN UINT8 *Buffer | |
| ); | |
| /// | |
| /// EFI_LBA_LIST_TERMINATOR | |
| /// | |
| #define EFI_LBA_LIST_TERMINATOR 0xFFFFFFFFFFFFFFFFULL | |
| /** | |
| Erases and initializes a firmware volume block. | |
| The EraseBlocks() function erases one or more blocks as denoted | |
| by the variable argument list. The entire parameter list of | |
| blocks must be verified before erasing any blocks. If a block is | |
| requested that does not exist within the associated firmware | |
| volume (it has a larger index than the last block of the | |
| firmware volume), the EraseBlocks() function must return the | |
| status code EFI_INVALID_PARAMETER without modifying the contents | |
| of the firmware volume. Implementations should be mindful that | |
| the firmware volume might be in the WriteDisabled state. If it | |
| is in this state, the EraseBlocks() function must return the | |
| status code EFI_ACCESS_DENIED without modifying the contents of | |
| the firmware volume. All calls to EraseBlocks() must be fully | |
| flushed to the hardware before the EraseBlocks() service | |
| returns. | |
| @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL | |
| instance. | |
| @param ... The variable argument list is a list of tuples. | |
| Each tuple describes a range of LBAs to erase | |
| and consists of the following: | |
| - An EFI_LBA that indicates the starting LBA | |
| - A UINTN that indicates the number of blocks to | |
| erase. | |
| The list is terminated with an | |
| EFI_LBA_LIST_TERMINATOR. For example, the | |
| following indicates that two ranges of blocks | |
| (5-7 and 10-11) are to be erased: EraseBlocks | |
| (This, 5, 3, 10, 2, EFI_LBA_LIST_TERMINATOR); | |
| @retval EFI_SUCCESS The erase request successfully | |
| completed. | |
| @retval EFI_ACCESS_DENIED The firmware volume is in the | |
| WriteDisabled state. | |
| @retval EFI_DEVICE_ERROR The block device is not functioning | |
| correctly and could not be written. | |
| The firmware device may have been | |
| partially erased. | |
| @retval EFI_INVALID_PARAMETER One or more of the LBAs listed | |
| in the variable argument list do | |
| not exist in the firmware volume. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI * EFI_FVB_ERASE_BLOCKS)( | |
| IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This, | |
| ... | |
| ); | |
| /// | |
| /// The Firmware Volume Block Protocol is the low-level interface | |
| /// to a firmware volume. File-level access to a firmware volume | |
| /// should not be done using the Firmware Volume Block Protocol. | |
| /// Normal access to a firmware volume must use the Firmware | |
| /// Volume Protocol. Typically, only the file system driver that | |
| /// produces the Firmware Volume Protocol will bind to the | |
| /// Firmware Volume Block Protocol. | |
| /// | |
| struct _EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL{ | |
| EFI_FVB_GET_ATTRIBUTES GetAttributes; | |
| EFI_FVB_SET_ATTRIBUTES SetAttributes; | |
| EFI_FVB_GET_PHYSICAL_ADDRESS GetPhysicalAddress; | |
| EFI_FVB_GET_BLOCK_SIZE GetBlockSize; | |
| EFI_FVB_READ Read; | |
| EFI_FVB_WRITE Write; | |
| EFI_FVB_ERASE_BLOCKS EraseBlocks; | |
| /// | |
| /// The handle of the parent firmware volume. | |
| /// | |
| EFI_HANDLE ParentHandle; | |
| }; | |
| extern EFI_GUID gEfiFirmwareVolumeBlockProtocolGuid; | |
| extern EFI_GUID gEfiFirmwareVolumeBlock2ProtocolGuid; | |
| #endif |