blob: f2c11b0bb086eea9574dde2ebdb040746fac0511 [file] [log] [blame]
/*
* Copyright 2004 Freescale Semiconductor.
* (C) Copyright 2002,2003 Motorola,Inc.
* Xianghua Xiao <X.Xiao@motorola.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* pm854 board configuration file
*
* Please refer to doc/README.mpc85xx for more info.
*
* Make sure you change the MAC address and other network params first,
* search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
#define CONFIG_MPC8540 1 /* MPC8540 specific */
#define CONFIG_PM854 1 /* PM854 board specific */
#define CONFIG_PCI
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_MEM_INIT_VALUE 0xDEADBEEF
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
/*
* sysclk for MPC85xx
*
* Two valid values are:
* 33000000
* 66000000
*
* Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
* is likely the desired value here, so that is now the default.
* The board, however, can run at 66MHz. In any event, this value
* must match the settings of some switches. Details can be found
* in the README.mpc85xxads.
*/
#ifndef CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_CLK_FREQ 66000000
#endif
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest region */
#define CFG_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
/*
* DDR Setup
*/
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
#if defined(CONFIG_SPD_EEPROM)
/*
* Determine DDR configuration from I2C interface.
*/
#define SPD_EEPROM_ADDRESS 0x58 /* DDR DIMM */
#else
/*
* Manually set up DDR parameters
*/
#define CFG_SDRAM_SIZE 256 /* DDR is 256 MB */
#define CFG_DDR_CS0_BNDS 0x0000000f /* 0-256MB */
#define CFG_DDR_CS0_CONFIG 0x80000102
#define CFG_DDR_TIMING_1 0x47444321
#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
#define CFG_DDR_CONTROL 0xc2008000 /* unbuffered,no DYN_PWR */
#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
#define CFG_DDR_INTERVAL 0x045b0100 /* autocharge,no open page */
#endif
/*
* SDRAM on the Local Bus
*/
#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
#define CFG_LBC_SDRAM_SIZE 0 /* LBC SDRAM is 0 MB */
#define CFG_FLASH_BASE 0xfe000000 /* start of 32 MB FLASH */
#define CFG_BR0_PRELIM 0xfe001801 /* port size 32bit */
#define CFG_OR0_PRELIM 0xfe006f67 /* 32 MB Flash */
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
#undef CFG_RAMBOOT
#endif
#define CONFIG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
#undef CONFIG_CLOCKS_IN_MHZ
/*
* Local Bus Definitions
*/
#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/*
* I2C
*/
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
#define CFG_I2C_OFFSET 0x3000
/*
* EEPROM configuration
*/
#define CFG_I2C_EEPROM_ADDR 0x58
#define CFG_I2C_EEPROM_ADDR_LEN 1
#define CFG_EEPROM_PAGE_WRITE_BITS 4
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
/*
* RTC configuration
*/
#define CONFIG_RTC_PCF8563
#define CFG_I2C_RTC_ADDR 0x51
/* RapidIO MMU */
#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCI1_IO_BASE 0xe2000000
#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_EEPRO100
#define CONFIG_E1000
#undef CONFIG_TULIP
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
#define PCI_ENET0_MEMADDR 0xe0000000
#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "TSEC1"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC1_FLAGS TSEC_GIGABIT
#define TSEC2_FLAGS TSEC_GIGABIT
#define CONFIG_MPC85XX_FEC 1
#define CONFIG_MPC85XX_FEC_NAME "FEC"
#define FEC_PHY_ADDR 3
#define FEC_PHYIDX 0
#define FEC_FLAGS 0
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1 1
#define CONFIG_HAS_ETH2 1
#endif /* CONFIG_TSEC_ENET */
/*
* Environment
*/
#ifndef CFG_RAMBOOT
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x80000)
#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#define CFG_ENV_SIZE 0x2000
#else
#define CFG_NO_FLASH 1 /* Flash is not usable now */
#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
#define CFG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_DATE
#define CONFIG_CMD_EEPROM
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
#if defined(CFG_RAMBOOT)
#undef CONFIG_CMD_ENV
#undef CONFIG_CMD_LOADS
#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
#define CONFIG_LOOPW
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Environment Configuration
*/
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_ETHADDR 00:40:42:01:00:00
#define CONFIG_ETH1ADDR 00:40:42:01:00:01
#define CONFIG_ETH2ADDR 00:40:42:01:00:02
#endif
#define CONFIG_ROOTPATH /opt/eldk/ppc_85xx
#define CONFIG_BOOTFILE pm854/uImage
#define CONFIG_HOSTNAME pm854
#define CONFIG_IPADDR 192.168.0.103
#define CONFIG_SERVERIP 192.168.0.64
#define CONFIG_GATEWAYIP 192.168.0.1
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 9600
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=400000\0" \
"ramdiskfile=pm854/uRamdisk\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"bootm $loadaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"bootm $loadaddr $ramdiskaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */