| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (c) 2018 Microsemi Corporation |
| */ |
| |
| #include <init.h> |
| #include <asm/global_data.h> |
| #include <linux/bitops.h> |
| |
| #include <asm/io.h> |
| #include <asm/types.h> |
| #include <asm/mipsregs.h> |
| |
| #include <mach/tlb.h> |
| #include <mach/ddr.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #if CFG_SYS_SDRAM_SIZE <= SZ_64M |
| #define MSCC_RAM_TLB_SIZE SZ_64M |
| #define MSCC_ATTRIB2 MMU_REGIO_INVAL |
| #elif CFG_SYS_SDRAM_SIZE <= SZ_128M |
| #define MSCC_RAM_TLB_SIZE SZ_64M |
| #define MSCC_ATTRIB2 MMU_REGIO_RW |
| #elif CFG_SYS_SDRAM_SIZE <= SZ_256M |
| #define MSCC_RAM_TLB_SIZE SZ_256M |
| #define MSCC_ATTRIB2 MMU_REGIO_INVAL |
| #elif CFG_SYS_SDRAM_SIZE <= SZ_512M |
| #define MSCC_RAM_TLB_SIZE SZ_256M |
| #define MSCC_ATTRIB2 MMU_REGIO_RW |
| #else |
| #define MSCC_RAM_TLB_SIZE SZ_512M |
| #define MSCC_ATTRIB2 MMU_REGIO_RW |
| #endif |
| |
| /* NOTE: lowlevel_init() function does not have access to the |
| * stack. Thus, all called functions must be inlined, and (any) local |
| * variables must be kept in registers. |
| */ |
| void vcoreiii_tlb_init(void) |
| { |
| register int tlbix = 0; |
| |
| /* |
| * Unlike most of the MIPS based SoCs, the IO register address |
| * are not in KSEG0. The mainline linux kernel built in legacy |
| * mode needs to access some of the registers very early in |
| * the boot and make the assumption that the bootloader has |
| * already configured them, so we have to match this |
| * expectation. |
| */ |
| create_tlb(tlbix++, MSCC_IO_ORIGIN1_OFFSET, SZ_16M, MMU_REGIO_RW, |
| MMU_REGIO_RW); |
| #ifdef CONFIG_SOC_LUTON |
| create_tlb(tlbix++, MSCC_IO_ORIGIN2_OFFSET, SZ_16M, MMU_REGIO_RW, |
| MMU_REGIO_RW); |
| #endif |
| |
| /* |
| * If U-Boot is located in NOR then we want to be able to use |
| * the data cache in order to boot in a decent duration |
| */ |
| create_tlb(tlbix++, MSCC_FLASH_TO, SZ_16M, MMU_REGIO_RO_C, |
| MMU_REGIO_RO_C); |
| create_tlb(tlbix++, MSCC_FLASH_TO + SZ_32M, SZ_16M, MMU_REGIO_RO_C, |
| MMU_REGIO_RO_C); |
| |
| /* |
| * Using cache for RAM also helps to improve boot time. Thanks |
| * to this the time to relocate U-Boot in RAM went from 2.092 |
| * secs to 0.104 secs. |
| */ |
| create_tlb(tlbix++, MSCC_DDR_TO, MSCC_RAM_TLB_SIZE, MMU_REGIO_RW, |
| MSCC_ATTRIB2); |
| |
| /* Enable mapping (using TLB) kuseg by clearing the bit ERL, |
| * which is set on reset. |
| */ |
| write_c0_status(read_c0_status() & ~ST0_ERL); |
| } |
| |
| int mach_cpu_init(void) |
| { |
| /* Speed up NOR flash access */ |
| #ifdef CONFIG_SOC_LUTON |
| writel(ICPU_PI_MST_CFG_TRISTATE_CTRL + |
| ICPU_PI_MST_CFG_CLK_DIV(4), BASE_CFG + ICPU_PI_MST_CFG); |
| |
| writel(ICPU_SPI_MST_CFG_FAST_READ_ENA + |
| ICPU_SPI_MST_CFG_CS_DESELECT_TIME(0x19) + |
| ICPU_SPI_MST_CFG_CLK_DIV(9), BASE_CFG + ICPU_SPI_MST_CFG); |
| #else |
| #if defined(CONFIG_SOC_OCELOT) || defined(CONFIG_SOC_SERVAL) |
| writel(ICPU_SPI_MST_CFG_CS_DESELECT_TIME(0x19) + |
| ICPU_SPI_MST_CFG_CLK_DIV(9), BASE_CFG + ICPU_SPI_MST_CFG); |
| #endif |
| #if defined(CONFIG_SOC_JR2) || defined(CONFIG_SOC_SERVALT) |
| writel(ICPU_SPI_MST_CFG_FAST_READ_ENA + |
| ICPU_SPI_MST_CFG_CS_DESELECT_TIME(0x19) + |
| ICPU_SPI_MST_CFG_CLK_DIV(14), BASE_CFG + ICPU_SPI_MST_CFG); |
| #endif |
| /* |
| * Legacy and mainline linux kernel expect that the |
| * interruption map was set as it was done by redboot. |
| */ |
| writel(~0, BASE_CFG + ICPU_DST_INTR_MAP(0)); |
| writel(0, BASE_CFG + ICPU_DST_INTR_MAP(1)); |
| writel(0, BASE_CFG + ICPU_DST_INTR_MAP(2)); |
| writel(0, BASE_CFG + ICPU_DST_INTR_MAP(3)); |
| #endif |
| return 0; |
| } |