| /** |
| * @file IxSspAcc.h |
| * |
| * @brief Header file for the IXP400 SSP Serial Port Access (IxSspAcc) |
| * |
| * @version $Revision: 0.1 $ |
| * |
| * @par |
| * IXP400 SW Release version 2.0 |
| * |
| * -- Copyright Notice -- |
| * |
| * @par |
| * Copyright 2001-2005, Intel Corporation. |
| * All rights reserved. |
| * |
| * @par |
| * SPDX-License-Identifier: BSD-3-Clause |
| * @par |
| * -- End of Copyright Notice -- |
| */ |
| |
| /** |
| * @defgroup IxSspAcc IXP400 SSP Serial Port Access (IxSspAcc) API |
| * |
| * @brief IXP400 SSP Serial Port Access Public API |
| * |
| * @{ |
| */ |
| #ifndef IXSSPACC_H |
| #define IXSSPACC_H |
| |
| #ifdef __ixp46X |
| |
| #include "IxOsal.h" |
| |
| /* |
| * Section for enum |
| */ |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @enum IxSspAccDataSize |
| * |
| * @brief The data sizes in bits that are supported by the protocol |
| */ |
| typedef enum |
| { |
| DATA_SIZE_TOO_SMALL = 0x2, |
| DATA_SIZE_4 = 0x3, |
| DATA_SIZE_5, |
| DATA_SIZE_6, |
| DATA_SIZE_7, |
| DATA_SIZE_8, |
| DATA_SIZE_9, |
| DATA_SIZE_10, |
| DATA_SIZE_11, |
| DATA_SIZE_12, |
| DATA_SIZE_13, |
| DATA_SIZE_14, |
| DATA_SIZE_15, |
| DATA_SIZE_16, |
| DATA_SIZE_TOO_BIG |
| } IxSspAccDataSize; |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @enum IxSspAccPortStatus |
| * |
| * @brief The status of the SSP port to be set to enable/disable |
| */ |
| typedef enum |
| { |
| SSP_PORT_DISABLE = 0x0, |
| SSP_PORT_ENABLE, |
| INVALID_SSP_PORT_STATUS |
| } IxSspAccPortStatus; |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @enum IxSspAccFrameFormat |
| * |
| * @brief The frame format that is to be used - SPI, SSP, or Microwire |
| */ |
| typedef enum |
| { |
| SPI_FORMAT = 0x0, |
| SSP_FORMAT, |
| MICROWIRE_FORMAT, |
| INVALID_FORMAT |
| } IxSspAccFrameFormat; |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @enum IxSspAccClkSource |
| * |
| * @brief The source to produce the SSP serial clock |
| */ |
| typedef enum |
| { |
| ON_CHIP_CLK = 0x0, |
| EXTERNAL_CLK, |
| INVALID_CLK_SOURCE |
| } IxSspAccClkSource; |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @enum IxSspAccSpiSclkPhase |
| * |
| * @brief The SPI SCLK Phase: |
| * 0 - SCLK is inactive one cycle at the start of a frame and 1/2 cycle at the |
| * end of a frame. |
| * 1 - SCLK is inactive 1/2 cycle at the start of a frame and one cycle at the |
| * end of a frame. |
| */ |
| typedef enum |
| { |
| START_ONE_END_HALF = 0x0, |
| START_HALF_END_ONE, |
| INVALID_SPI_PHASE |
| } IxSspAccSpiSclkPhase; |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @enum IxSspAccSpiSclkPolarity |
| * |
| * @brief The SPI SCLK Polarity can be set to either low or high. |
| */ |
| typedef enum |
| { |
| SPI_POLARITY_LOW = 0x0, |
| SPI_POLARITY_HIGH, |
| INVALID_SPI_POLARITY |
| } IxSspAccSpiSclkPolarity; |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @enum IxSspAccMicrowireCtlWord |
| * |
| * @brief The Microwire control word can be either 8 or 16 bit. |
| */ |
| typedef enum |
| { |
| MICROWIRE_8_BIT = 0x0, |
| MICROWIRE_16_BIT, |
| INVALID_MICROWIRE_CTL_WORD |
| } IxSspAccMicrowireCtlWord; |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @enum IxSspAccFifoThreshold |
| * |
| * @brief The threshold in frames (each frame is defined by IxSspAccDataSize) |
| * that can be set for the FIFO to trigger a threshold exceed when |
| * checking with the ExceedThresholdCheck functions or an interrupt |
| * when it is enabled. |
| */ |
| typedef enum |
| { |
| FIFO_TSHLD_1 = 0x0, |
| FIFO_TSHLD_2, |
| FIFO_TSHLD_3, |
| FIFO_TSHLD_4, |
| FIFO_TSHLD_5, |
| FIFO_TSHLD_6, |
| FIFO_TSHLD_7, |
| FIFO_TSHLD_8, |
| FIFO_TSHLD_9, |
| FIFO_TSHLD_10, |
| FIFO_TSHLD_11, |
| FIFO_TSHLD_12, |
| FIFO_TSHLD_13, |
| FIFO_TSHLD_14, |
| FIFO_TSHLD_15, |
| FIFO_TSHLD_16, |
| INVALID_FIFO_TSHLD |
| } IxSspAccFifoThreshold; |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @enum IX_SSP_STATUS |
| * |
| * @brief The statuses that can be returned in a SSP Serial Port Access |
| */ |
| typedef enum |
| { |
| IX_SSP_SUCCESS = IX_SUCCESS, /**< Success status */ |
| IX_SSP_FAIL, /**< Fail status */ |
| IX_SSP_RX_FIFO_OVERRUN_HANDLER_MISSING, /**< |
| Rx FIFO Overrun handler is NULL. */ |
| IX_SSP_RX_FIFO_HANDLER_MISSING, /**< |
| Rx FIFO threshold hit or above handler is NULL |
| */ |
| IX_SSP_TX_FIFO_HANDLER_MISSING, /**< |
| Tx FIFO threshold hit or below handler is NULL |
| */ |
| IX_SSP_FIFO_NOT_EMPTY_FOR_SETTING_CTL_CMD, /**< |
| Tx FIFO not empty and therefore microwire |
| control command size setting is not allowed. */ |
| IX_SSP_INVALID_FRAME_FORMAT_ENUM_VALUE, /**< |
| frame format selected is invalid. */ |
| IX_SSP_INVALID_DATA_SIZE_ENUM_VALUE, /**< |
| data size selected is invalid. */ |
| IX_SSP_INVALID_CLOCK_SOURCE_ENUM_VALUE, /**< |
| source clock selected is invalid. */ |
| IX_SSP_INVALID_TX_FIFO_THRESHOLD_ENUM_VALUE, /**< |
| Tx FIFO threshold selected is invalid. */ |
| IX_SSP_INVALID_RX_FIFO_THRESHOLD_ENUM_VALUE, /**< |
| Rx FIFO threshold selected is invalid. */ |
| IX_SSP_INVALID_SPI_PHASE_ENUM_VALUE, /**< |
| SPI phase selected is invalid. */ |
| IX_SSP_INVALID_SPI_POLARITY_ENUM_VALUE, /**< |
| SPI polarity selected is invalid. */ |
| IX_SSP_INVALID_MICROWIRE_CTL_CMD_ENUM_VALUE, /**< |
| Microwire control command selected is invalid |
| */ |
| IX_SSP_INT_UNBIND_FAIL, /**< Interrupt unbind fail to unbind SSP |
| interrupt */ |
| IX_SSP_INT_BIND_FAIL, /**< Interrupt bind fail during init */ |
| IX_SSP_RX_FIFO_NOT_EMPTY, /**< |
| Rx FIFO not empty while trying to change data |
| size. */ |
| IX_SSP_TX_FIFO_NOT_EMPTY, /**< |
| Rx FIFO not empty while trying to change data |
| size or microwire control command size. */ |
| IX_SSP_POLL_MODE_BLOCKING, /**< |
| poll mode selected blocks interrupt mode from |
| being selected. */ |
| IX_SSP_TX_FIFO_HIT_BELOW_THRESHOLD, /**< |
| Tx FIFO level hit or below threshold. */ |
| IX_SSP_TX_FIFO_EXCEED_THRESHOLD, /**< |
| Tx FIFO level exceeded threshold. */ |
| IX_SSP_RX_FIFO_HIT_ABOVE_THRESHOLD, /**< |
| Rx FIFO level hit or exceeded threshold. */ |
| IX_SSP_RX_FIFO_BELOW_THRESHOLD, /**< |
| Rx FIFO level below threshold. */ |
| IX_SSP_BUSY, /**< SSP is busy. */ |
| IX_SSP_IDLE, /**< SSP is idle. */ |
| IX_SSP_OVERRUN_OCCURRED, /**< |
| SSP has experienced an overrun. */ |
| IX_SSP_NO_OVERRUN, /**< |
| SSP did not experience an overrun. */ |
| IX_SSP_NOT_SUPORTED, /**< hardware does not support SSP */ |
| IX_SSP_NOT_INIT, /**< SSP Access not intialized */ |
| IX_SSP_NULL_POINTER /**< parameter passed in is NULL */ |
| } IX_SSP_STATUS; |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @brief SSP Rx FIFO Overrun handler |
| * |
| * This function is called for the client to handle Rx FIFO Overrun that occurs |
| * in the SSP hardware |
| */ |
| typedef void (*RxFIFOOverrunHandler)(void); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @brief SSP Rx FIFO Threshold hit or above handler |
| * |
| * This function is called for the client to handle Rx FIFO threshold hit or |
| * or above that occurs in the SSP hardware |
| */ |
| typedef void (*RxFIFOThresholdHandler)(void); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @brief SSP Tx FIFO Threshold hit or below handler |
| * |
| * This function is called for the client to handle Tx FIFO threshold hit or |
| * or below that occurs in the SSP hardware |
| */ |
| typedef void (*TxFIFOThresholdHandler)(void); |
| |
| |
| /* |
| * Section for struct |
| */ |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @brief contains all the variables required to initialize the SSP serial port |
| * hardware. |
| * |
| * Structure to be filled and used for calling initialization |
| */ |
| typedef struct |
| { |
| IxSspAccFrameFormat FrameFormatSelected;/**<Select between SPI, SSP and |
| Microwire. */ |
| IxSspAccDataSize DataSizeSelected; /**<Select between 4 and 16. */ |
| IxSspAccClkSource ClkSourceSelected; /**<Select clock source to be |
| on-chip or external. */ |
| IxSspAccFifoThreshold TxFIFOThresholdSelected; |
| /**<Select Tx FIFO threshold |
| between 1 to 16. */ |
| IxSspAccFifoThreshold RxFIFOThresholdSelected; |
| /**<Select Rx FIFO threshold |
| between 1 to 16. */ |
| BOOL RxFIFOIntrEnable; /**<Enable/disable Rx FIFO |
| threshold interrupt. Disabling |
| this interrupt will require |
| the use of the polling function |
| RxFIFOExceedThresholdCheck. */ |
| BOOL TxFIFOIntrEnable; /**<Enable/disable Tx FIFO |
| threshold interrupt. Disabling |
| this interrupt will require |
| the use of the polling function |
| TxFIFOExceedThresholdCheck. */ |
| RxFIFOThresholdHandler RxFIFOThsldHdlr; /**<Pointer to function to handle |
| a Rx FIFO interrupt. */ |
| TxFIFOThresholdHandler TxFIFOThsldHdlr; /**<Pointer to function to handle |
| a Tx FIFO interrupt. */ |
| RxFIFOOverrunHandler RxFIFOOverrunHdlr; /**<Pointer to function to handle |
| a Rx FIFO overrun interrupt. */ |
| BOOL LoopbackEnable; /**<Select operation mode to be |
| normal or loopback mode. */ |
| IxSspAccSpiSclkPhase SpiSclkPhaseSelected; |
| /**<Select SPI SCLK phase to start |
| with one inactive cycle and end |
| with 1/2 inactive cycle or |
| start with 1/2 inactive cycle |
| and end with one inactive |
| cycle. (Only used in |
| SPI format). */ |
| IxSspAccSpiSclkPolarity SpiSclkPolaritySelected; |
| /**<Select SPI SCLK idle state |
| to be low or high. (Only used in |
| SPI format). */ |
| IxSspAccMicrowireCtlWord MicrowireCtlWordSelected; |
| /**<Select Microwire control |
| format to be 8 or 16-bit. (Only |
| used in Microwire format). */ |
| UINT8 SerialClkRateSelected; /**<Select between 0 (1.8432Mbps) |
| and 255 (7.2Kbps). The |
| formula used is Bit rate = |
| 3.6864x10^6 / |
| (2 x (SerialClkRateSelect + 1)) |
| */ |
| } IxSspInitVars; |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @brief contains counters of the SSP statistics |
| * |
| * Structure contains all values of counters and associated overflows. |
| */ |
| typedef struct |
| { |
| UINT32 ixSspRcvCounter; /**<Total frames received. */ |
| UINT32 ixSspXmitCounter; /**<Total frames transmitted. */ |
| UINT32 ixSspOverflowCounter;/**<Total occurrences of overflow. */ |
| } IxSspAccStatsCounters; |
| |
| |
| /* |
| * Section for prototypes interface functions |
| */ |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccInit ( |
| IxSspInitVars *initVarsSelected); |
| * |
| * @brief Initializes the SSP Access module. |
| * |
| * @param "IxSspAccInitVars [in] *initVarsSelected" - struct containing required |
| * variables for initialization |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will initialize the SSP Serial Port hardware to the user specified |
| * configuration. Then it will enable the SSP Serial Port. |
| * *NOTE*: Once interrupt or polling mode is selected, the mode cannot be |
| * changed via the interrupt enable/disable function but the init needs to be |
| * called again to change it. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Successfully initialize and enable the SSP |
| * serial port. |
| * - IX_SSP_RX_FIFO_HANDLER_MISSING - interrupt mode is selected but RX FIFO |
| * handler pointer is NULL |
| * - IX_SSP_TX_FIFO_HANDLER_MISSING - interrupt mode is selected but TX FIFO |
| * handler pointer is NULL |
| * - IX_SSP_RX_FIFO_OVERRUN_HANDLER_MISSING - interrupt mode is selected but |
| * RX FIFO Overrun handler pointer is NULL |
| * - IX_SSP_RX_FIFO_NOT_EMPTY - Rx FIFO not empty, data size change is not |
| * allowed. |
| * - IX_SSP_TX_FIFO_NOT_EMPTY - Tx FIFO not empty, data size change is not |
| * allowed. |
| * - IX_SSP_INVALID_FRAME_FORMAT_ENUM_VALUE - frame format selected is invalid |
| * - IX_SSP_INVALID_DATA_SIZE_ENUM_VALUE - data size selected is invalid |
| * - IX_SSP_INVALID_CLOCK_SOURCE_ENUM_VALUE - clock source selected is invalid |
| * - IX_SSP_INVALID_TX_FIFO_THRESHOLD_ENUM_VALUE - Tx FIFO threshold level |
| * selected is invalid |
| * - IX_SSP_INVALID_RX_FIFO_THRESHOLD_ENUM_VALUE - Rx FIFO threshold level |
| * selected is invalid |
| * - IX_SSP_INVALID_SPI_PHASE_ENUM_VALUE - SPI phase selected is invalid |
| * - IX_SSP_INVALID_SPI_POLARITY_ENUM_VALUE - SPI polarity selected is invalid |
| * - IX_SSP_INVALID_MICROWIRE_CTL_CMD_ENUM_VALUE - microwire control command |
| * size is invalid |
| * - IX_SSP_INT_UNBIND_FAIL - interrupt handler failed to unbind SSP interrupt |
| * - IX_SSP_INT_BIND_FAIL - interrupt handler failed to bind to SSP interrupt |
| * hardware trigger |
| * - IX_SSP_NOT_SUPORTED - hardware does not support SSP |
| * - IX_SSP_NULL_POINTER - parameter passed in is NULL |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccInit (IxSspInitVars *initVarsSelected); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccUninit ( |
| void) |
| * |
| * @brief Un-initializes the SSP Serial Port Access component |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will disable the SSP Serial Port hardware. The client can call the |
| * init function again if they wish to enable the SSP. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - successfully uninit SSP component |
| * - IX_SSP_INT_UNBIND_FAIL - interrupt handler failed to unbind SSP interrupt |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccUninit (void); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccFIFODataSubmit ( |
| UINT16 *data, |
| UINT32 amtOfData) |
| * |
| * @brief Inserts data into the SSP Serial Port's FIFO |
| * |
| * @param "UINT16 [in] *data" - pointer to the location to transmit the data |
| * from |
| * "UINT32 [in] amtOfData" - number of data to be transmitted. |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will insert the amount of data specified by "amtOfData" from buffer |
| * pointed to by "data" into the FIFO to be transmitted by the hardware. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Data inserted successfully into FIFO |
| * - IX_SSP_FAIL - FIFO insufficient space |
| * - IX_SSP_NULL_POINTER - data pointer passed by client is NULL |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccFIFODataSubmit ( |
| UINT16* data, |
| UINT32 amtOfData); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccFIFODataReceive ( |
| UINT16 *data, |
| UINT32 amtOfData) |
| * |
| * @brief Extract data from the SSP Serial Port's FIFO |
| * |
| * @param "UINT16 [in] *data" - pointer to the location to receive the data into |
| * "UINT32 [in] amtOfData" - number of data to be received. |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will extract the amount of data specified by "amtOfData" from the |
| * FIFO already received by the hardware into the buffer pointed to by "data". |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Data extracted successfully from FIFO |
| * - IX_SSP_FAIL - FIFO has no data |
| * - IX_SSP_NULL_POINTER - data pointer passed by client is NULL |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccFIFODataReceive ( |
| UINT16* data, |
| UINT32 amtOfData); |
| |
| |
| /** |
| * Polling Functions |
| */ |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccTxFIFOHitOrBelowThresholdCheck ( |
| void) |
| * |
| * @brief Check if the Tx FIFO threshold has been hit or fallen below. |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will return whether the Tx FIFO threshold has been exceeded or not |
| * |
| * @return |
| * - IX_SSP_TX_FIFO_HIT_BELOW_THRESHOLD - Tx FIFO level hit or below threshold . |
| * - IX_SSP_TX_FIFO_EXCEED_THRESHOLD - Tx FIFO level exceeded threshold. |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccTxFIFOHitOrBelowThresholdCheck ( |
| void); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccRxFIFOHitOrAboveThresholdCheck ( |
| void) |
| * |
| * @brief Check if the Rx FIFO threshold has been hit or exceeded. |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will return whether the Rx FIFO level is below threshold or not |
| * |
| * @return |
| * - IX_SSP_RX_FIFO_HIT_ABOVE_THRESHOLD - Rx FIFO level hit or exceeded threshold |
| * - IX_SSP_RX_FIFO_BELOW_THRESHOLD - Rx FIFO level below threshold |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccRxFIFOHitOrAboveThresholdCheck ( |
| void); |
| |
| |
| /** |
| * Configuration functions |
| * |
| * NOTE: These configurations are not required to be called once init is called |
| * unless configurations need to be changed on the fly. |
| */ |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccSSPPortStatusSet ( |
| IxSspAccPortStatus portStatusSelected) |
| * |
| * @brief Enables/disables the SSP Serial Port hardware. |
| * |
| * @param "IxSspAccPortStatus [in] portStatusSelected" - Set the SSP port to |
| * enable or disable |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will enable/disable the SSP Serial Port hardware. |
| * NOTE: This function is called by init to enable the SSP after setting up the |
| * configurations and by uninit to disable the SSP. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Port status set with valid enum value |
| * - IX_SSP_FAIL - invalid enum value |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccSSPPortStatusSet ( |
| IxSspAccPortStatus portStatusSelected); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccFrameFormatSelect ( |
| IxSspAccFrameFormat frameFormatSelected) |
| * |
| * @brief Sets the frame format for the SSP Serial Port hardware |
| * |
| * @param "IxSspAccFrameFormat [in] frameFormatSelected" - The frame format of |
| * SPI, SSP or Microwire can be selected as the format |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will set the format for the transfers via user input. |
| * *NOTE*: The SSP hardware will be disabled to clear the FIFOs. Then its |
| * previous state (enabled/disabled) restored after changing the format. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - frame format set with valid enum value |
| * - IX_SSP_INVALID_FRAME_FORMAT_ENUM_VALUE - invalid frame format value |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccFrameFormatSelect ( |
| IxSspAccFrameFormat frameFormatSelected); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccDataSizeSelect ( |
| IxSspAccDataSize dataSizeSelected) |
| * |
| * @brief Sets the data size for transfers |
| * |
| * @param "IxSspAccDataSize [in] dataSizeSelected" - The data size between 4 |
| * and 16 that can be selected for data transfers |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will set the data size for the transfers via user input. It will |
| * disallow the change of the data size if either of the Rx/Tx FIFO is not |
| * empty to prevent data loss. |
| * *NOTE*: The SSP port will be disabled if the FIFOs are found to be empty and |
| * if between the check and disabling of the SSP (which clears the |
| * FIFOs) data is received into the FIFO, it might be lost. |
| * *NOTE*: The FIFOs can be cleared by disabling the SSP Port if necessary to |
| * force the data size change. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - data size set with valid enum value |
| * - IX_SSP_RX_FIFO_NOT_EMPTY - Rx FIFO not empty, data size change is not |
| * allowed. |
| * - IX_SSP_TX_FIFO_NOT_EMPTY - Tx FIFO not empty, data size change is not |
| * allowed. |
| * - IX_SSP_INVALID_DATA_SIZE_ENUM_VALUE - invalid enum value |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccDataSizeSelect ( |
| IxSspAccDataSize dataSizeSelected); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccClockSourceSelect( |
| IxSspAccClkSource clkSourceSelected) |
| * |
| * @brief Sets the clock source of the SSP Serial Port hardware |
| * |
| * @param "IxSspAccClkSource [in] clkSourceSelected" - The clock source from |
| * either external source on on-chip can be selected as the source |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will set the clock source for the transfers via user input. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - clock source set with valid enum value |
| * - IX_SSP_INVALID_CLOCK_SOURCE_ENUM_VALUE - invalid enum value |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccClockSourceSelect ( |
| IxSspAccClkSource clkSourceSelected); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccSerialClockRateConfigure ( |
| UINT8 serialClockRateSelected) |
| * |
| * @brief Sets the on-chip Serial Clock Rate of the SSP Serial Port hardware. |
| * |
| * @param "UINT8 [in] serialClockRateSelected" - The serial clock rate that can |
| * be set is between 7.2Kbps and 1.8432Mbps. The formula used is |
| * Bit rate = 3.6864x10^6 / (2 x (SerialClockRateSelected + 1)) |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will set the serial clock rate for the transfers via user input. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Serial clock rate configured successfully |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccSerialClockRateConfigure ( |
| UINT8 serialClockRateSelected); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccRxFIFOIntEnable ( |
| RxFIFOThresholdHandler rxFIFOIntrHandler) |
| * |
| * @brief Enables service request interrupt whenever the Rx FIFO hits its |
| * threshold |
| * |
| * @param "void [in] *rxFIFOIntrHandler(UINT32)" - function pointer to the |
| * interrupt handler for the Rx FIFO exceeded. |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will enable the service request interrupt for the Rx FIFO |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Rx FIFO level interrupt enabled successfully |
| * - IX_SSP_RX_FIFO_HANDLER_MISSING - missing handler for Rx FIFO level interrupt |
| * - IX_SSP_POLL_MODE_BLOCKING - poll mode is selected at init, interrupt not |
| * allowed to be enabled. Use init to enable interrupt mode. |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccRxFIFOIntEnable ( |
| RxFIFOThresholdHandler rxFIFOIntrHandler); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccRxFIFOIntDisable ( |
| void) |
| * |
| * @brief Disables service request interrupt of the Rx FIFO. |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will disable the service request interrupt of the Rx FIFO. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Rx FIFO Interrupt disabled successfully |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccRxFIFOIntDisable ( |
| void); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccTxFIFOIntEnable ( |
| TxFIFOThresholdHandler txFIFOIntrHandler) |
| * |
| * @brief Enables service request interrupt of the Tx FIFO. |
| * |
| * @param "void [in] *txFIFOIntrHandler(UINT32)" - function pointer to the |
| * interrupt handler for the Tx FIFO exceeded. |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will enable the service request interrupt of the Tx FIFO. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Tx FIFO level interrupt enabled successfully |
| * - IX_SSP_TX_FIFO_HANDLER_MISSING - missing handler for Tx FIFO level interrupt |
| * - IX_SSP_POLL_MODE_BLOCKING - poll mode is selected at init, interrupt not |
| * allowed to be enabled. Use init to enable interrupt mode. |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccTxFIFOIntEnable ( |
| TxFIFOThresholdHandler txFIFOIntrHandler); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccTxFIFOIntDisable ( |
| void) |
| * |
| * @brief Disables service request interrupt of the Tx FIFO |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will disable the service request interrupt of the Tx FIFO |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Tx FIFO Interrupt disabled successfuly. |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccTxFIFOIntDisable ( |
| void); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccLoopbackEnable ( |
| BOOL loopbackEnable) |
| * |
| * @brief Enables/disables the loopback mode |
| * |
| * @param "BOOL [in] loopbackEnable" - true to enable and false to disable. |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will set the mode of operation to either loopback or normal mode |
| * according to the user input. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Loopback enabled successfully |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccLoopbackEnable ( |
| BOOL loopbackEnable); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccSpiSclkPolaritySet ( |
| IxSspAccSpiSclkPolarity spiSclkPolaritySelected) |
| * |
| * @brief Sets the SPI SCLK Polarity to Low or High |
| * |
| * @param - "IxSspAccSpiSclkPolarity [in] spiSclkPolaritySelected" - SPI SCLK |
| * polarity that can be selected to either high or low |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API is only used for the SPI frame format and will set the SPI SCLK polarity |
| * to either low or high |
| * |
| * @return |
| * - IX_SSP_SUCCESS - SPI Sclk polarity set with valid enum value |
| * - IX_SSP_INVALID_SPI_POLARITY_ENUM_VALUE - invalid SPI polarity value |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccSpiSclkPolaritySet ( |
| IxSspAccSpiSclkPolarity spiSclkPolaritySelected); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccSpiSclkPhaseSet ( |
| IxSspAccSpiSclkPhase spiSclkPhaseSelected) |
| * |
| * @brief Sets the SPI SCLK Phase |
| * |
| * @param "IxSspAccSpiSclkPhase [in] spiSclkPhaseSelected" - Phase of either |
| * the SCLK is inactive one cycle at the start of a frame and 1/2 |
| * cycle at the end of a frame, OR |
| * the SCLK is inactive 1/2 cycle at the start of a frame and one |
| * cycle at the end of a frame. |
| * |
| * Global Data : |
| * - IX_SSP_SUCCESS - SPI Sclk phase set with valid enum value |
| * - IX_SSP_INVALID_SPI_PHASE_ENUM_VALUE - invalid SPI phase value |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * This API is only used for the SPI frame format and will set the SPI SCLK |
| * phase according to user input. |
| * |
| * @return |
| * - None |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccSpiSclkPhaseSet ( |
| IxSspAccSpiSclkPhase spiSclkPhaseSelected); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccMicrowireControlWordSet ( |
| IxSspAccMicrowireCtlWord microwireCtlWordSelected) |
| * |
| * @brief Sets the Microwire control word to 8 or 16 bit format |
| * |
| * @param "IxSspAccMicrowireCtlWord [in] microwireCtlWordSelected" - Microwire |
| * control word format can be either 8 or 16 bit format |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API is only used for the Microwire frame format and will set the |
| * control word to 8 or 16 bit format |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Microwire Control Word set with valid enum value |
| * - IX_SSP_TX_FIFO_NOT_EMPTY - Tx FIFO not empty, data size change is not |
| * allowed. |
| * - IX_SSP_INVALID_MICROWIRE_CTL_CMD_ENUM_VALUE - invalid enum value |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccMicrowireControlWordSet ( |
| IxSspAccMicrowireCtlWord microwireCtlWordSelected); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccTxFIFOThresholdSet ( |
| IxSspAccFifoThreshold txFIFOThresholdSelected) |
| * |
| * @brief Sets the Tx FIFO Threshold. |
| * |
| * @param "IxSspAccFifoThreshold [in] txFIFOThresholdSelected" - Threshold that |
| * is set for a Tx FIFO service request to be triggered |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will set the threshold for a Tx FIFO threshold to be triggered |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Tx FIFO Threshold set with valid enum value |
| * - IX_SSP_INVALID_TX_FIFO_THRESHOLD_ENUM_VALUE - invalid enum value |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccTxFIFOThresholdSet ( |
| IxSspAccFifoThreshold txFIFOThresholdSelected); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccRxFIFOThresholdSet ( |
| IxSspAccFifoThreshold rxFIFOThresholdSelected) |
| * |
| * @brief Sets the Rx FIFO Threshold. |
| * |
| * @param "IxSspAccFifoThreshold [in] rxFIFOThresholdSelected" - Threshold that |
| * is set for a Tx FIFO service request to be triggered |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will will set the threshold for a Rx FIFO threshold to be triggered |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Rx FIFO Threshold set with valid enum value |
| * - IX_SSP_INVALID_RX_FIFO_THRESHOLD_ENUM_VALUE - invalid enum value |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccRxFIFOThresholdSet ( |
| IxSspAccFifoThreshold rxFIFOThresholdSelected); |
| |
| |
| /** |
| * Debug functions |
| */ |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccStatsGet ( |
| IxSspAccStatsCounters *sspStats) |
| * |
| * @brief Returns the SSP Statistics through the pointer passed in |
| * |
| * @param "IxSspAccStatsCounters [in] *sspStats" - SSP statistics counter will |
| * be read and written to the location pointed by this pointer. |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will return the statistics counters of the SSP transfers. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - Stats obtained into the pointer provided successfully |
| * - IX_SSP_FAIL - client provided pointer is NULL |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccStatsGet ( |
| IxSspAccStatsCounters *sspStats); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccStatsReset ( |
| void) |
| * |
| * @brief Resets the SSP Statistics |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will reset the SSP statistics counters. |
| * |
| * @return |
| * - None |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC void |
| ixSspAccStatsReset ( |
| void); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccShow ( |
| void) |
| * |
| * @brief Display SSP status registers and statistics counters. |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will display the status registers of the SSP and the statistics |
| * counters. |
| * |
| * @return |
| * - IX_SSP_SUCCESS - SSP show called successfully. |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccShow ( |
| void); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccSSPBusyCheck ( |
| void) |
| * |
| * @brief Determine the state of the SSP serial port hardware. |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will return the state of the SSP serial port hardware - busy or |
| * idle |
| * |
| * @return |
| * - IX_SSP_BUSY - SSP is busy |
| * - IX_SSP_IDLE - SSP is idle. |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccSSPBusyCheck ( |
| void); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccTxFIFOLevelGet ( |
| void) |
| * |
| * @brief Obtain the Tx FIFO's level |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will return the level of the Tx FIFO |
| * |
| * @return |
| * - 0..16; 0 can also mean SSP not initialized and will need to be init. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC UINT8 |
| ixSspAccTxFIFOLevelGet ( |
| void); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccRxFIFOLevelGet ( |
| void) |
| * |
| * @brief Obtain the Rx FIFO's level |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will return the level of the Rx FIFO |
| * |
| * @return |
| * - 0..16; 0 can also mean SSP not initialized and will need to be init. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC UINT8 |
| ixSspAccRxFIFOLevelGet ( |
| void); |
| |
| /** |
| * @ingroup IxSspAcc |
| * |
| * @fn ixSspAccRxFIFOOverrunCheck ( |
| void) |
| * |
| * @brief Check if the Rx FIFO has overrun its FIFOs |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will return whether the Rx FIFO has overrun its 16 FIFOs |
| * |
| * @return |
| * - IX_SSP_OVERRUN_OCCURRED - Rx FIFO overrun occurred |
| * - IX_SSP_NO_OVERRUN - Rx FIFO did not overrun |
| * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_SSP_STATUS |
| ixSspAccRxFIFOOverrunCheck ( |
| void); |
| |
| #endif /* __ixp46X */ |
| #endif /* IXSSPACC_H */ |