| #ifndef __LINUX_PS2MULT_H |
| #define __LINUX_PS2MULT_H |
| |
| #define kbd_request_region() ps2mult_init() |
| #define kbd_request_irq(handler) ps2mult_request_irq(handler) |
| |
| #define kbd_read_input() ps2mult_read_input() |
| #define kbd_read_status() ps2mult_read_status() |
| #define kbd_write_output(val) ps2mult_write_output(val) |
| #define kbd_write_command(val) ps2mult_write_command(val) |
| |
| #define aux_request_irq(hand, dev_id) 0 |
| #define aux_free_irq(dev_id) |
| |
| #define PS2MULT_KB_SELECTOR 0xA0 |
| #define PS2MULT_MS_SELECTOR 0xA1 |
| #define PS2MULT_ESCAPE 0x7D |
| #define PS2MULT_BSYNC 0x7E |
| #define PS2MULT_SESSION_START 0x55 |
| #define PS2MULT_SESSION_END 0x56 |
| |
| #define PS2BUF_SIZE 512 /* power of 2, please */ |
| |
| #ifndef CONFIG_PS2MULT_DELAY |
| #define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */ |
| #endif |
| |
| /* PS/2 controller interface (include/asm/keyboard.h) |
| */ |
| extern int ps2mult_init (void); |
| extern int ps2mult_request_irq(void (*handler)(void *)); |
| extern u_char ps2mult_read_input(void); |
| extern u_char ps2mult_read_status(void); |
| extern void ps2mult_write_output(u_char val); |
| extern void ps2mult_write_command(u_char val); |
| |
| extern void ps2mult_early_init (void); |
| extern void ps2mult_callback (int in_cnt); |
| |
| /* Simple serial interface |
| */ |
| extern int ps2ser_init(void); |
| extern void ps2ser_putc(int chr); |
| extern int ps2ser_getc(void); |
| extern int ps2ser_check(void); |
| |
| |
| /* Serial related stuff |
| */ |
| struct serial_state { |
| int baud_base; |
| int irq; |
| u8 *iomem_base; |
| }; |
| |
| #define UART_RX 0 /* In: Receive buffer (DLAB=0) */ |
| #define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */ |
| #define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */ |
| |
| #define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */ |
| #define UART_IER 1 /* Out: Interrupt Enable Register */ |
| |
| #define UART_IIR 2 /* In: Interrupt ID Register */ |
| #define UART_FCR 2 /* Out: FIFO Control Register */ |
| |
| #define UART_LCR 3 /* Out: Line Control Register */ |
| #define UART_MCR 4 /* Out: Modem Control Register */ |
| #define UART_LSR 5 /* In: Line Status Register */ |
| #define UART_MSR 6 /* In: Modem Status Register */ |
| #define UART_SCR 7 /* I/O: Scratch Register */ |
| |
| /* |
| * These are the definitions for the FIFO Control Register |
| * (16650 only) |
| */ |
| #define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */ |
| #define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ |
| #define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ |
| #define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ |
| #define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */ |
| #define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */ |
| #define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */ |
| #define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */ |
| #define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */ |
| |
| /* |
| * These are the definitions for the Line Control Register |
| * |
| * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting |
| * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits. |
| */ |
| #define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ |
| #define UART_LCR_SBC 0x40 /* Set break control */ |
| #define UART_LCR_SPAR 0x20 /* Stick parity (?) */ |
| #define UART_LCR_EPAR 0x10 /* Even parity select */ |
| #define UART_LCR_PARITY 0x08 /* Parity Enable */ |
| #define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */ |
| #define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */ |
| #define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */ |
| #define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */ |
| #define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ |
| |
| /* |
| * These are the definitions for the Line Status Register |
| */ |
| #define UART_LSR_TEMT 0x40 /* Transmitter empty */ |
| #define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */ |
| #define UART_LSR_BI 0x10 /* Break interrupt indicator */ |
| #define UART_LSR_FE 0x08 /* Frame error indicator */ |
| #define UART_LSR_PE 0x04 /* Parity error indicator */ |
| #define UART_LSR_OE 0x02 /* Overrun error indicator */ |
| #define UART_LSR_DR 0x01 /* Receiver data ready */ |
| |
| /* |
| * These are the definitions for the Interrupt Identification Register |
| */ |
| #define UART_IIR_NO_INT 0x01 /* No interrupts pending */ |
| #define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ |
| |
| #define UART_IIR_MSI 0x00 /* Modem status interrupt */ |
| #define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ |
| #define UART_IIR_RDI 0x04 /* Receiver data interrupt */ |
| #define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ |
| |
| /* |
| * These are the definitions for the Interrupt Enable Register |
| */ |
| #define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ |
| #define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ |
| #define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ |
| #define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ |
| |
| /* |
| * These are the definitions for the Modem Control Register |
| */ |
| #define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ |
| #define UART_MCR_OUT2 0x08 /* Out2 complement */ |
| #define UART_MCR_OUT1 0x04 /* Out1 complement */ |
| #define UART_MCR_RTS 0x02 /* RTS complement */ |
| #define UART_MCR_DTR 0x01 /* DTR complement */ |
| |
| /* |
| * These are the definitions for the Modem Status Register |
| */ |
| #define UART_MSR_DCD 0x80 /* Data Carrier Detect */ |
| #define UART_MSR_RI 0x40 /* Ring Indicator */ |
| #define UART_MSR_DSR 0x20 /* Data Set Ready */ |
| #define UART_MSR_CTS 0x10 /* Clear to Send */ |
| #define UART_MSR_DDCD 0x08 /* Delta DCD */ |
| #define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ |
| #define UART_MSR_DDSR 0x02 /* Delta DSR */ |
| #define UART_MSR_DCTS 0x01 /* Delta CTS */ |
| #define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */ |
| |
| #endif /* __LINUX_PS2MULT_H */ |