blob: 90fbfca87f2b982a405a7c263fa6af5130d173fa [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* dts file for Xilinx ZynqMP ZCU104
*
* (C) Copyright 2017 - 2021, Xilinx, Inc.
*
* Michal Simek <michal.simek@amd.com>
*/
/dts-v1/;
#include "zynqmp.dtsi"
#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
#include <dt-bindings/phy/phy.h>
/ {
model = "ZynqMP ZCU104 RevA";
compatible = "xlnx,zynqmp-zcu104-revA", "xlnx,zynqmp-zcu104", "xlnx,zynqmp";
aliases {
ethernet0 = &gem3;
i2c0 = &i2c1;
mmc0 = &sdhci1;
nvmem0 = &eeprom;
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
spi0 = &qspi;
usb0 = &usb0;
};
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
clock_8t49n287_5: clk125 {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <125000000>;
};
clock_8t49n287_2: clk26 {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <26000000>;
};
clock_8t49n287_3: clk27 {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <27000000>;
};
};
&can1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1_default>;
};
&dcc {
status = "okay";
};
&fpd_dma_chan1 {
status = "okay";
};
&fpd_dma_chan2 {
status = "okay";
};
&fpd_dma_chan3 {
status = "okay";
};
&fpd_dma_chan4 {
status = "okay";
};
&fpd_dma_chan5 {
status = "okay";
};
&fpd_dma_chan6 {
status = "okay";
};
&fpd_dma_chan7 {
status = "okay";
};
&fpd_dma_chan8 {
status = "okay";
};
&gem3 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gem3_default>;
mdio: mdio {
#address-cells = <1>;
#size-cells = <0>;
phy0: ethernet-phy@c {
#phy-cells = <1>;
compatible = "ethernet-phy-id2000.a231";
reg = <0xc>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
ti,dp83867-rxctrl-strap-quirk;
reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
};
};
};
&gpio {
status = "okay";
};
&gpu {
status = "okay";
};
&i2c1 {
status = "okay";
clock-frequency = <400000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1_default>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
/* Another connection to this bus via PL i2c via PCA9306 - u45 */
i2c-mux@74 { /* u34 */
compatible = "nxp,pca9548";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x74>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
/*
* IIC_EEPROM 1kB memory which uses 256B blocks
* where every block has different address.
* 0 - 256B address 0x54
* 256B - 512B address 0x55
* 512B - 768B address 0x56
* 768B - 1024B address 0x57
*/
eeprom: eeprom@54 { /* u23 */
compatible = "atmel,24c08";
reg = <0x54>;
#address-cells = <1>;
#size-cells = <1>;
};
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
/* 8T49N287 - u182 */
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
irps5401_43: irps5401@43 { /* IRPS5401 - u175 */
compatible = "infineon,irps5401";
reg = <0x43>; /* pmbus / i2c 0x13 */
};
irps5401_44: irps5401@44 { /* IRPS5401 - u180 */
compatible = "infineon,irps5401";
reg = <0x44>; /* pmbus / i2c 0x14 */
};
};
i2c@4 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
tca6416_u97: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
/*
* IRQ not connected
* Lines:
* 0 - IRPS5401_ALERT_B
* 1 - HDMI_8T49N241_INT_ALM
* 2 - MAX6643_OT_B
* 3 - MAX6643_FANFAIL_B
* 5 - IIC_MUX_RESET_B
* 6 - GEM3_EXP_RESET_B
* 7 - FMC_LPC_PRSNT_M2C_B
* 4, 10 - 17 - not connected
*/
};
};
i2c@5 {
#address-cells = <1>;
#size-cells = <0>;
reg = <5>;
};
i2c@7 {
#address-cells = <1>;
#size-cells = <0>;
reg = <7>;
};
/* 3, 6 not connected */
};
};
&pinctrl0 {
status = "okay";
pinctrl_can1_default: can1-default {
mux {
function = "can1";
groups = "can1_6_grp";
};
conf {
groups = "can1_6_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
drive-strength = <12>;
};
conf-rx {
pins = "MIO25";
bias-high-impedance;
};
conf-tx {
pins = "MIO24";
bias-disable;
};
};
pinctrl_i2c1_default: i2c1-default {
mux {
groups = "i2c1_4_grp";
function = "i2c1";
};
conf {
groups = "i2c1_4_grp";
bias-pull-up;
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
drive-strength = <12>;
};
};
pinctrl_i2c1_gpio: i2c1-gpio {
mux {
groups = "gpio0_16_grp", "gpio0_17_grp";
function = "gpio0";
};
conf {
groups = "gpio0_16_grp", "gpio0_17_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
drive-strength = <12>;
};
};
pinctrl_gem3_default: gem3-default {
mux {
function = "ethernet3";
groups = "ethernet3_0_grp";
};
conf {
groups = "ethernet3_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
drive-strength = <12>;
};
conf-rx {
pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
"MIO75";
bias-high-impedance;
low-power-disable;
};
conf-tx {
pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
"MIO69";
bias-disable;
low-power-enable;
};
mux-mdio {
function = "mdio3";
groups = "mdio3_0_grp";
};
conf-mdio {
groups = "mdio3_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
bias-disable;
};
};
pinctrl_sdhci1_default: sdhci1-default {
mux {
groups = "sdio1_0_grp";
function = "sdio1";
};
conf {
groups = "sdio1_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
bias-disable;
drive-strength = <12>;
};
mux-cd {
groups = "sdio1_cd_0_grp";
function = "sdio1_cd";
};
conf-cd {
groups = "sdio1_cd_0_grp";
bias-high-impedance;
bias-pull-up;
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
};
pinctrl_uart0_default: uart0-default {
mux {
groups = "uart0_4_grp";
function = "uart0";
};
conf {
groups = "uart0_4_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
drive-strength = <12>;
};
conf-rx {
pins = "MIO18";
bias-high-impedance;
};
conf-tx {
pins = "MIO19";
bias-disable;
};
};
pinctrl_uart1_default: uart1-default {
mux {
groups = "uart1_5_grp";
function = "uart1";
};
conf {
groups = "uart1_5_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
drive-strength = <12>;
};
conf-rx {
pins = "MIO21";
bias-high-impedance;
};
conf-tx {
pins = "MIO20";
bias-disable;
};
};
pinctrl_usb0_default: usb0-default {
mux {
groups = "usb0_0_grp";
function = "usb0";
};
conf {
groups = "usb0_0_grp";
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO52", "MIO53", "MIO55";
bias-high-impedance;
drive-strength = <12>;
slew-rate = <SLEW_RATE_FAST>;
};
conf-tx {
pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
"MIO60", "MIO61", "MIO62", "MIO63";
bias-disable;
drive-strength = <4>;
slew-rate = <SLEW_RATE_SLOW>;
};
};
};
&psgtr {
status = "okay";
/* nc, sata, usb3, dp */
clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
clock-names = "ref1", "ref2", "ref3";
};
&qspi {
status = "okay";
flash@0 {
compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */
#address-cells = <1>;
#size-cells = <1>;
reg = <0x0>;
spi-tx-bus-width = <4>;
spi-rx-bus-width = <4>;
spi-max-frequency = <108000000>; /* Based on DC1 spec */
partition@0 { /* for testing purpose */
label = "qspi-fsbl-uboot";
reg = <0x0 0x100000>;
};
partition@100000 { /* for testing purpose */
label = "qspi-linux";
reg = <0x100000 0x500000>;
};
partition@600000 { /* for testing purpose */
label = "qspi-device-tree";
reg = <0x600000 0x20000>;
};
partition@620000 { /* for testing purpose */
label = "qspi-rootfs";
reg = <0x620000 0x5E0000>;
};
};
};
&rtc {
status = "okay";
};
&sata {
status = "okay";
/* SATA OOB timing settings */
ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
phy-names = "sata-phy";
phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
};
/* SD1 with level shifter */
&sdhci1 {
status = "okay";
no-1-8-v;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdhci1_default>;
xlnx,mio-bank = <1>;
disable-wp;
};
&uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0_default>;
};
&uart1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1_default>;
};
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
phy-names = "usb3-phy";
phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
maximum-speed = "super-speed";
};
&watchdog0 {
status = "okay";
};
&xilinx_ams {
status = "okay";
};
&ams_ps {
status = "okay";
};
&ams_pl {
status = "okay";
};
&zynqmp_dpdma {
status = "okay";
};
&zynqmp_dpsub {
status = "okay";
phy-names = "dp-phy0", "dp-phy1";
phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
<&psgtr 0 PHY_TYPE_DP 1 3>;
};