| /* |
| * (C) Copyright 2010 |
| * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_405EP 1 /* this is a PPC405 CPU */ |
| #define CONFIG_IOCON 1 /* on a IoCon board */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0xFFFC0000 |
| |
| /* |
| * Include common defines/options for all AMCC eval boards |
| */ |
| #define CONFIG_HOSTNAME iocon |
| #define CONFIG_IDENT_STRING " iocon 0.06" |
| #include "amcc-common.h" |
| |
| #define CONFIG_BOARD_EARLY_INIT_F |
| #define CONFIG_BOARD_EARLY_INIT_R |
| #define CONFIG_LAST_STAGE_INIT |
| #define CONFIG_SYS_GENERIC_BOARD |
| |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ |
| |
| /* |
| * Configure PLL |
| */ |
| #define PLLMR0_DEFAULT PLLMR0_266_133_66 |
| #define PLLMR1_DEFAULT PLLMR1_266_133_66 |
| |
| #undef CONFIG_ZERO_BOOTDELAY_CHECK /* ignore keypress on bootdelay==0 */ |
| |
| /* new uImage format support */ |
| #define CONFIG_FIT |
| #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ |
| #define CONFIG_FIT_DISABLE_SHA256 |
| |
| #define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environment vars */ |
| |
| /* |
| * Default environment variables |
| */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_AMCC_DEF_ENV \ |
| CONFIG_AMCC_DEF_ENV_POWERPC \ |
| CONFIG_AMCC_DEF_ENV_NOR_UPD \ |
| "kernel_addr=fc000000\0" \ |
| "fdt_addr=fc1e0000\0" \ |
| "ramdisk_addr=fc200000\0" \ |
| "" |
| |
| #define CONFIG_PHY_ADDR 4 /* PHY address */ |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ |
| |
| /* |
| * Commands additional to the ones defined in amcc-common.h |
| */ |
| #define CONFIG_CMD_CACHE |
| #define CONFIG_CMD_FPGAD |
| #undef CONFIG_CMD_EEPROM |
| #undef CONFIG_CMD_ELF |
| #undef CONFIG_CMD_I2C |
| #undef CONFIG_CMD_IRQ |
| #undef CONFIG_CMD_NFS |
| |
| /* |
| * SDRAM configuration (please see cpu/ppc/sdram.[ch]) |
| */ |
| #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ |
| |
| /* SDRAM timings used in datasheet */ |
| #define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */ |
| #define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */ |
| #define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE period */ |
| #define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */ |
| #define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */ |
| |
| /* |
| * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. |
| * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. |
| * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD. |
| * The Linux BASE_BAUD define should match this configuration. |
| * baseBaud = cpuClock/(uartDivisor*16) |
| * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, |
| * set Linux BASE_BAUD to 403200. |
| */ |
| #define CONFIG_CONS_INDEX 1 /* Use UART0 */ |
| #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ |
| #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ |
| #define CONFIG_SYS_BASE_BAUD 691200 |
| |
| /* |
| * I2C stuff |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_PPC4XX |
| #define CONFIG_SYS_I2C_PPC4XX_CH0 |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 |
| #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F |
| #define CONFIG_SYS_I2C_IHS |
| |
| #define CONFIG_SYS_I2C_SPEED 400000 |
| #define CONFIG_SYS_SPD_BUS_NUM 4 |
| |
| #define CONFIG_PCA953X /* NXP PCA9554 */ |
| #define CONFIG_PCA9698 /* NXP PCA9698 */ |
| |
| #define CONFIG_SYS_I2C_IHS_CH0 |
| #define CONFIG_SYS_I2C_IHS_SPEED_0 50000 |
| #define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F |
| #define CONFIG_SYS_I2C_IHS_CH1 |
| #define CONFIG_SYS_I2C_IHS_SPEED_1 50000 |
| #define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F |
| #define CONFIG_SYS_I2C_IHS_CH2 |
| #define CONFIG_SYS_I2C_IHS_SPEED_2 50000 |
| #define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F |
| #define CONFIG_SYS_I2C_IHS_CH3 |
| #define CONFIG_SYS_I2C_IHS_SPEED_3 50000 |
| #define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F |
| |
| /* |
| * Software (bit-bang) I2C driver configuration |
| */ |
| #define CONFIG_SYS_I2C_SOFT |
| #define CONFIG_SYS_I2C_SOFT_SPEED 50000 |
| #define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F |
| #define I2C_SOFT_DECLARATIONS2 |
| #define CONFIG_SYS_I2C_SOFT_SPEED_2 50000 |
| #define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F |
| #define I2C_SOFT_DECLARATIONS3 |
| #define CONFIG_SYS_I2C_SOFT_SPEED_3 50000 |
| #define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F |
| #define I2C_SOFT_DECLARATIONS4 |
| #define CONFIG_SYS_I2C_SOFT_SPEED_4 50000 |
| #define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F |
| |
| #define CONFIG_SYS_ICS8N3QV01_I2C {5, 6, 7, 8} |
| #define CONFIG_SYS_CH7301_I2C {5, 6, 7, 8} |
| #define CONFIG_SYS_DP501_I2C {0, 1, 2, 3} |
| |
| #ifndef __ASSEMBLY__ |
| void fpga_gpio_set(unsigned int bus, int pin); |
| void fpga_gpio_clear(unsigned int bus, int pin); |
| int fpga_gpio_get(unsigned int bus, int pin); |
| #endif |
| |
| #define I2C_ACTIVE { } |
| #define I2C_TRISTATE { } |
| #define I2C_READ \ |
| (fpga_gpio_get(I2C_ADAP_HWNR, 0x0040) ? 1 : 0) |
| #define I2C_SDA(bit) \ |
| do { \ |
| if (bit) \ |
| fpga_gpio_set(I2C_ADAP_HWNR, 0x0040); \ |
| else \ |
| fpga_gpio_clear(I2C_ADAP_HWNR, 0x0040); \ |
| } while (0) |
| #define I2C_SCL(bit) \ |
| do { \ |
| if (bit) \ |
| fpga_gpio_set(I2C_ADAP_HWNR, 0x0020); \ |
| else \ |
| fpga_gpio_clear(I2C_ADAP_HWNR, 0x0020); \ |
| } while (0) |
| #define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */ |
| |
| /* |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ |
| #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ |
| |
| #define CONFIG_SYS_FLASH_BASE 0xFC000000 |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sectors per chip*/ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase/ms */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write/ms */ |
| |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buff'd writes */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO /* 'E' for empty sector on flinfo */ |
| #define CONFIG_SYS_FLASH_QUIET_TEST 1 /* no warn upon unknown flash */ |
| |
| #ifdef CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ |
| #define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| #endif |
| |
| /* |
| * PPC405 GPIO Configuration |
| */ |
| #define CONFIG_SYS_4xx_GPIO_TABLE { /* GPIO Alternate1 */ \ |
| { \ |
| /* GPIO Core 0 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO1 TS1E */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO2 TS2E */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO3 TS1O */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO4 TS2O */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO5 TS3 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO6 TS4 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO7 TS5 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO8 TS6 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO9 TrcClk */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10 PerCS1 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11 PerCS2 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12 PerCS3 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO13 PerCS4 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO14 PerAddr03 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO15 PerAddr04 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO16 PerAddr05 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17 IRQ0 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18 IRQ1 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19 IRQ2 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO20 IRQ3 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO21 IRQ4 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO22 IRQ5 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO23 IRQ6 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24 UART0_DCD */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25 UART0_DSR */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26 UART0_RI */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27 UART0_DTR */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28 UART1_Rx */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29 UART1_Tx */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO30 RejectPkt0 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO31 RejectPkt1 */ \ |
| } \ |
| } |
| |
| /* |
| * Definitions for initial stack pointer and data area (in data cache) |
| */ |
| /* use on chip memory (OCM) for temperary stack until sdram is tested */ |
| #define CONFIG_SYS_TEMP_STACK_OCM 1 |
| |
| /* On Chip Memory location */ |
| #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 |
| #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* in SDRAM */ |
| #define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area */ |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET \ |
| (CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /* |
| * External Bus Controller (EBC) Setup |
| */ |
| |
| /* Memory Bank 0 (NOR-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB0AP 0xa382a880 |
| #define CONFIG_SYS_EBC_PB0CR 0xFC0DA000 |
| |
| /* Memory Bank 1 (NVRAM) initializatio */ |
| #define CONFIG_SYS_EBC_PB1AP 0x92015480 |
| #define CONFIG_SYS_EBC_PB1CR 0xFB858000 |
| |
| /* Memory Bank 2 (FPGA0) initialization */ |
| #define CONFIG_SYS_FPGA0_BASE 0x7f100000 |
| #define CONFIG_SYS_EBC_PB2AP 0x02825080 |
| #define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FPGA0_BASE | 0x1a000) |
| |
| #define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE |
| #define CONFIG_SYS_FPGA_DONE(k) 0x0010 |
| |
| #define CONFIG_SYS_FPGA_COUNT 1 |
| |
| #define CONFIG_SYS_MCLINK_MAX 3 |
| |
| #define CONFIG_SYS_FPGA_PTR \ |
| { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL } |
| |
| /* Memory Bank 3 (Latches) initialization */ |
| #define CONFIG_SYS_LATCH_BASE 0x7f200000 |
| #define CONFIG_SYS_EBC_PB3AP 0x02025080 |
| #define CONFIG_SYS_EBC_PB3CR 0x7f21a000 |
| |
| #define CONFIG_SYS_LATCH0_RESET 0xffef |
| #define CONFIG_SYS_LATCH0_BOOT 0xffff |
| #define CONFIG_SYS_LATCH1_RESET 0xffff |
| #define CONFIG_SYS_LATCH1_BOOT 0xffff |
| |
| /* |
| * OSD Setup |
| */ |
| #define CONFIG_SYS_MPC92469AC |
| #define CONFIG_SYS_OSD_SCREENS 1 |
| #define CONFIG_SYS_DP501_DIFFERENTIAL |
| #define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */ |
| |
| #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ |
| #define CONFIG_BITBANGMII_MULTI |
| |
| #endif /* __CONFIG_H */ |