| source "drivers/net/phy/Kconfig" |
| source "drivers/net/pfe_eth/Kconfig" |
| source "drivers/net/fsl-mc/Kconfig" |
| |
| config DM_ETH |
| bool "Enable Driver Model for Ethernet drivers" |
| depends on DM |
| help |
| Enable driver model for Ethernet. |
| |
| The eth_*() interface will be implemented by the UCLASS_ETH class |
| This is currently implemented in net/eth-uclass.c |
| Look in include/net.h for details. |
| |
| config DM_MDIO |
| bool "Enable Driver Model for MDIO devices" |
| depends on DM_ETH && PHYLIB |
| help |
| Enable driver model for MDIO devices |
| |
| Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as |
| stand-alone devices. Useful in particular for systems that support |
| DM_ETH and have a stand-alone MDIO hardware block shared by multiple |
| Ethernet interfaces. |
| This is currently implemented in net/mdio-uclass.c |
| Look in include/miiphy.h for details. |
| |
| config DM_MDIO_MUX |
| bool "Enable Driver Model for MDIO MUX devices" |
| depends on DM_MDIO |
| help |
| Enable driver model for MDIO MUX devices |
| |
| Adds UCLASS_MDIO_MUX DM class supporting MDIO MUXes. Useful for |
| systems that support DM_MDIO and integrate one or multiple muxes on |
| the MDIO bus. |
| This is currently implemented in net/mdio-mux-uclass.c |
| Look in include/miiphy.h for details. |
| |
| config MDIO_SANDBOX |
| depends on DM_MDIO && SANDBOX |
| default y |
| bool "Sandbox: Mocked MDIO driver" |
| help |
| This driver implements dummy read/write/reset MDIO functions mimicking |
| a bus with a single PHY. |
| |
| This driver is used in for testing in test/dm/mdio.c |
| |
| config MDIO_MUX_SANDBOX |
| depends on DM_MDIO_MUX && MDIO_SANDBOX |
| default y |
| bool "Sandbox: Mocked MDIO-MUX driver" |
| help |
| This driver implements dummy select/deselect ops mimicking a MUX on |
| the MDIO bux. It uses mdio_sandbox driver as parent MDIO. |
| |
| This driver is used for testing in test/dm/mdio.c |
| |
| config DM_ETH_PHY |
| bool "Enable Driver Model for Ethernet Generic PHY drivers" |
| depends on DM |
| help |
| Enable driver model for Ethernet Generic PHY . |
| |
| menuconfig NETDEVICES |
| bool "Network device support" |
| depends on NET |
| default y if DM_ETH |
| help |
| You must select Y to enable any network device support |
| Generally if you have any networking support this is a given |
| |
| If unsure, say Y |
| |
| if NETDEVICES |
| |
| config PHY_GIGE |
| bool "Enable GbE PHY status parsing and configuration" |
| help |
| Enables support for parsing the status output and for |
| configuring GbE PHYs (affects the inner workings of some |
| commands and miiphyutil.c). |
| |
| config AG7XXX |
| bool "Atheros AG7xxx Ethernet MAC support" |
| depends on DM_ETH && ARCH_ATH79 |
| select PHYLIB |
| help |
| This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is |
| present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips. |
| |
| |
| config ALTERA_TSE |
| bool "Altera Triple-Speed Ethernet MAC support" |
| depends on DM_ETH |
| select PHYLIB |
| help |
| This driver supports the Altera Triple-Speed (TSE) Ethernet MAC. |
| Please find details on the "Triple-Speed Ethernet MegaCore Function |
| Resource Center" of Altera. |
| |
| config BCM_SF2_ETH |
| bool "Broadcom SF2 (Starfighter2) Ethernet support" |
| select PHYLIB |
| help |
| This is an abstract framework which provides a generic interface |
| to MAC and DMA management for multiple Broadcom SoCs such as |
| Cygnus, NSP and bcm28155_ap platforms. |
| |
| config BCM_SF2_ETH_DEFAULT_PORT |
| int "Broadcom SF2 (Starfighter2) Ethernet default port number" |
| depends on BCM_SF2_ETH |
| default 0 |
| help |
| Default port number for the Starfighter2 ethernet driver. |
| |
| config BCM_SF2_ETH_GMAC |
| bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support" |
| depends on BCM_SF2_ETH |
| help |
| This flag enables the ethernet support for Broadcom platforms with |
| GMAC such as Cygnus. This driver is based on the framework provided |
| by the BCM_SF2_ETH driver. |
| Say Y to any bcmcygnus based platforms. |
| |
| config BCM6348_ETH |
| bool "BCM6348 EMAC support" |
| depends on DM_ETH && ARCH_BMIPS |
| select DMA |
| select DMA_CHANNELS |
| select MII |
| select PHYLIB |
| help |
| This driver supports the BCM6348 Ethernet MAC. |
| |
| config BCM6368_ETH |
| bool "BCM6368 EMAC support" |
| depends on DM_ETH && ARCH_BMIPS |
| select DMA |
| select MII |
| help |
| This driver supports the BCM6368 Ethernet MAC. |
| |
| config BCMGENET |
| bool "BCMGENET V5 support" |
| depends on DM_ETH |
| select PHYLIB |
| help |
| This driver supports the BCMGENET Ethernet MAC. |
| |
| config DWC_ETH_QOS |
| bool "Synopsys DWC Ethernet QOS device support" |
| depends on DM_ETH |
| select PHYLIB |
| help |
| This driver supports the Synopsys Designware Ethernet QOS (Quality |
| Of Service) IP block. The IP supports many options for bus type, |
| clocking/reset structure, and feature list. |
| |
| config DWC_ETH_QOS_IMX |
| bool "Synopsys DWC Ethernet QOS device support for IMX" |
| depends on DWC_ETH_QOS |
| help |
| The Synopsys Designware Ethernet QOS IP block with the specific |
| configuration used in IMX soc. |
| |
| config DWC_ETH_QOS_STM32 |
| bool "Synopsys DWC Ethernet QOS device support for STM32" |
| depends on DWC_ETH_QOS |
| default y if ARCH_STM32MP |
| help |
| The Synopsys Designware Ethernet QOS IP block with the specific |
| configuration used in STM32MP soc. |
| |
| config DWC_ETH_QOS_TEGRA186 |
| bool "Synopsys DWC Ethernet QOS device support for TEGRA186" |
| depends on DWC_ETH_QOS |
| default y if TEGRA186 |
| help |
| The Synopsys Designware Ethernet QOS IP block with specific |
| configuration used in NVIDIA's Tegra186 chip. |
| |
| config E1000 |
| bool "Intel PRO/1000 Gigabit Ethernet support" |
| depends on (DM_ETH && DM_PCI) || !DM_ETH |
| help |
| This driver supports Intel(R) PRO/1000 gigabit ethernet family of |
| adapters. For more information on how to identify your adapter, go |
| to the Adapter & Driver ID Guide at: |
| |
| <http://support.intel.com/support/network/adapter/pro100/21397.htm> |
| |
| config E1000_SPI_GENERIC |
| bool "Allow access to the Intel 8257x SPI bus" |
| depends on E1000 |
| help |
| Allow generic access to the SPI bus on the Intel 8257x, for |
| example with the "sspi" command. |
| |
| config E1000_SPI |
| bool "Enable SPI bus utility code" |
| depends on E1000 |
| help |
| Utility code for direct access to the SPI bus on Intel 8257x. |
| This does not do anything useful unless you set at least one |
| of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC. |
| |
| config CMD_E1000 |
| bool "Enable the e1000 command" |
| depends on E1000 |
| help |
| This enables the 'e1000' management command for E1000 devices. When |
| used on devices with SPI support you can reprogram the EEPROM from |
| U-Boot. |
| |
| config EEPRO100 |
| bool "Intel PRO/100 82557/82559/82559ER Fast Ethernet support" |
| help |
| This driver supports Intel(R) PRO/100 82557/82559/82559ER fast |
| ethernet family of adapters. |
| |
| config ETH_SANDBOX |
| depends on DM_ETH && SANDBOX |
| default y |
| bool "Sandbox: Mocked Ethernet driver" |
| help |
| This driver simply responds with fake ARP replies and ping |
| replies that are used to verify network stack functionality |
| |
| This driver is particularly useful in the test/dm/eth.c tests |
| |
| config ETH_SANDBOX_RAW |
| depends on DM_ETH && SANDBOX |
| default y |
| bool "Sandbox: Bridge to Linux Raw Sockets" |
| help |
| This driver is a bridge from the bottom of the network stack |
| in U-Boot to the RAW AF_PACKET API in Linux. This allows real |
| network traffic to be tested from within sandbox. See |
| doc/arch/index.rst for more details. |
| |
| config ETH_DESIGNWARE |
| bool "Synopsys Designware Ethernet MAC" |
| select PHYLIB |
| imply ETH_DESIGNWARE_SOCFPGA if ARCH_SOCFPGA |
| help |
| This MAC is present in SoCs from various vendors. It supports |
| 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to |
| provide the PHY (physical media interface). |
| |
| config ETH_DESIGNWARE_SOCFPGA |
| select REGMAP |
| select SYSCON |
| bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC" |
| depends on DM_ETH && ETH_DESIGNWARE |
| help |
| The Altera SoCFPGA requires additional configuration of the |
| Altera system manager to correctly interface with the PHY. |
| This code handles those SoC specifics. |
| |
| config ETH_DESIGNWARE_S700 |
| bool "Actins S700 glue driver for Synopsys Designware Ethernet MAC" |
| depends on DM_ETH && ETH_DESIGNWARE |
| help |
| This provides glue layer to use Synopsys Designware Ethernet MAC |
| present on Actions S700 SoC. |
| |
| config ETHOC |
| bool "OpenCores 10/100 Mbps Ethernet MAC" |
| help |
| This MAC is present in OpenRISC and Xtensa XTFPGA boards. |
| |
| config FEC_MXC_SHARE_MDIO |
| bool "Share the MDIO bus for FEC controller" |
| depends on FEC_MXC |
| |
| config FEC_MXC_MDIO_BASE |
| hex "MDIO base address for the FEC controller" |
| depends on FEC_MXC_SHARE_MDIO |
| help |
| This specifies the MDIO registers base address. It is used when |
| two FEC controllers share MDIO bus. |
| |
| config FEC_MXC |
| bool "FEC Ethernet controller" |
| depends on MX28 || MX5 || MX6 || MX7 || IMX8 || IMX8M || VF610 |
| help |
| This driver supports the 10/100 Fast Ethernet controller for |
| NXP i.MX processors. |
| |
| config FMAN_ENET |
| bool "Freescale FMan ethernet support" |
| depends on ARM || PPC |
| help |
| This driver support the Freescale FMan Ethernet controller |
| |
| config FTMAC100 |
| bool "Ftmac100 Ethernet Support" |
| help |
| This MAC is present in Andestech SoCs. |
| |
| config FTGMAC100 |
| bool "Ftgmac100 Ethernet Support" |
| depends on DM_ETH |
| select PHYLIB |
| help |
| This driver supports the Faraday's FTGMAC100 Gigabit SoC |
| Ethernet controller that can be found on Aspeed SoCs (which |
| include NCSI). |
| |
| It is fully compliant with IEEE 802.3 specification for |
| 10/100 Mbps Ethernet and IEEE 802.3z specification for 1000 |
| Mbps Ethernet and includes Reduced Media Independent |
| Interface (RMII) and Reduced Gigabit Media Independent |
| Interface (RGMII) interfaces. It adopts an AHB bus interface |
| and integrates a link list DMA engine with direct M-Bus |
| accesses for transmitting and receiving packets. It has |
| independent TX/RX fifos, supports half and full duplex (1000 |
| Mbps mode only supports full duplex), flow control for full |
| duplex and backpressure for half duplex. |
| |
| The FTGMAC100 also implements IP, TCP, UDP checksum offloads |
| and supports IEEE 802.1Q VLAN tag insertion and removal. It |
| offers high-priority transmit queue for QoS and CoS |
| applications. |
| |
| |
| config MCFFEC |
| bool "ColdFire Ethernet Support" |
| depends on DM_ETH |
| select PHYLIB |
| help |
| This driver supports the network interface units in the |
| ColdFire family. |
| |
| config FSLDMAFEC |
| bool "ColdFire DMA Ethernet Support" |
| depends on DM_ETH |
| select PHYLIB |
| help |
| This driver supports the network interface units in the |
| ColdFire family. |
| |
| config KS8851_MLL |
| bool "Microchip KS8851-MLL controller driver" |
| help |
| The Microchip KS8851 parallel bus external ethernet interface chip. |
| |
| if KS8851_MLL |
| if !DM_ETH |
| config KS8851_MLL_BASEADDR |
| hex "Microchip KS8851-MLL Base Address" |
| help |
| Define this to hold the physical address of the device (I/O space) |
| endif #DM_ETH |
| endif #KS8851_MLL |
| |
| config MVGBE |
| bool "Marvell Orion5x/Kirkwood network interface support" |
| depends on ARCH_KIRKWOOD || ARCH_ORION5X |
| select PHYLIB if DM_ETH |
| help |
| This driver supports the network interface units in the |
| Marvell Orion5x and Kirkwood SoCs |
| |
| config MVNETA |
| bool "Marvell Armada XP/385/3700 network interface support" |
| depends on ARMADA_XP || ARMADA_38X || ARMADA_3700 |
| select PHYLIB |
| help |
| This driver supports the network interface units in the |
| Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs |
| |
| config MVPP2 |
| bool "Marvell Armada 375/7K/8K network interface support" |
| depends on ARMADA_375 || ARMADA_8K |
| select PHYLIB |
| select MVMDIO |
| select DM_MDIO |
| help |
| This driver supports the network interface units in the |
| Marvell ARMADA 375, 7K and 8K SoCs. |
| |
| config MACB |
| bool "Cadence MACB/GEM Ethernet Interface" |
| depends on DM_ETH |
| select PHYLIB |
| help |
| The Cadence MACB ethernet interface is found on many Atmel |
| AT91 and SAMA5 parts. This driver also supports the Cadence |
| GEM (Gigabit Ethernet MAC) found in some ARM SoC devices. |
| Say Y to include support for the MACB/GEM chip. |
| |
| config MACB_ZYNQ |
| bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq" |
| depends on MACB |
| help |
| The Cadence MACB ethernet interface was used on Zynq platform. |
| Say Y to enable support for the MACB/GEM in Zynq chip. |
| |
| config MT7628_ETH |
| bool "MediaTek MT7628 Ethernet Interface" |
| depends on SOC_MT7628 |
| select PHYLIB |
| help |
| The MediaTek MT7628 ethernet interface is used on MT7628 and |
| MT7688 based boards. |
| |
| config PCH_GBE |
| bool "Intel Platform Controller Hub EG20T GMAC driver" |
| depends on DM_ETH && DM_PCI |
| select PHYLIB |
| help |
| This MAC is present in Intel Platform Controller Hub EG20T. It |
| supports 10/100/1000 Mbps operation. |
| |
| config RGMII |
| bool "Enable RGMII" |
| help |
| Enable the support of the Reduced Gigabit Media-Independent |
| Interface (RGMII). |
| |
| config MII |
| bool "Enable MII" |
| help |
| Enable support of the Media-Independent Interface (MII) |
| |
| config PCNET |
| bool "AMD PCnet series Ethernet controller driver" |
| help |
| This driver supports AMD PCnet series fast ethernet family of |
| PCI chipsets/adapters. |
| |
| config RTL8139 |
| bool "Realtek 8139 series Ethernet controller driver" |
| help |
| This driver supports Realtek 8139 series fast ethernet family of |
| PCI chipsets/adapters. |
| |
| config RTL8169 |
| bool "Realtek 8169 series Ethernet controller driver" |
| help |
| This driver supports Realtek 8169 series gigabit ethernet family of |
| PCI/PCIe chipsets/adapters. |
| |
| config SMC911X |
| bool "SMSC LAN911x and LAN921x controller driver" |
| |
| if SMC911X |
| |
| if !DM_ETH |
| config SMC911X_BASE |
| hex "SMC911X Base Address" |
| help |
| Define this to hold the physical address |
| of the device (I/O space) |
| endif #DM_ETH |
| |
| choice |
| prompt "SMC911X bus width" |
| default SMC911X_16_BIT |
| |
| config SMC911X_32_BIT |
| bool "Enable 32-bit interface" |
| |
| config SMC911X_16_BIT |
| bool "Enable 16-bit interface" |
| help |
| Define this if data bus is 16 bits. If your processor |
| automatically converts one 32 bit word to two 16 bit |
| words you may also try CONFIG_SMC911X_32_BIT. |
| |
| endchoice |
| endif #SMC911X |
| |
| config SUN7I_GMAC |
| bool "Enable Allwinner GMAC Ethernet support" |
| help |
| Enable the support for Sun7i GMAC Ethernet controller |
| |
| config SUN7I_GMAC_FORCE_TXERR |
| bool "Force PA17 as gmac function" |
| depends on SUN7I_GMAC |
| help |
| Some ethernet phys needs TXERR control. Since the GMAC |
| doesn't have such signal, setting PA17 as GMAC function |
| makes the pin output low, which enables data transmission. |
| |
| config SUN4I_EMAC |
| bool "Allwinner Sun4i Ethernet MAC support" |
| depends on DM_ETH |
| select PHYLIB |
| help |
| This driver supports the Allwinner based SUN4I Ethernet MAC. |
| |
| config SUN8I_EMAC |
| bool "Allwinner Sun8i Ethernet MAC support" |
| depends on DM_ETH |
| select PHYLIB |
| select PHY_GIGE |
| help |
| This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC. |
| It can be found in H3/A64/A83T based SoCs and compatible with both |
| External and Internal PHYs. |
| |
| config SH_ETHER |
| bool "Renesas SH Ethernet MAC" |
| select PHYLIB |
| help |
| This driver supports the Ethernet for Renesas SH and ARM SoCs. |
| |
| source "drivers/net/ti/Kconfig" |
| |
| config TULIP |
| bool "DEC Tulip DC2114x Ethernet support" |
| depends on (DM_ETH && DM_PCI) || !DM_ETH |
| help |
| This driver supports DEC DC2114x Fast ethernet chips. |
| |
| config XILINX_AXIEMAC |
| depends on DM_ETH |
| select PHYLIB |
| select MII |
| bool "Xilinx AXI Ethernet" |
| help |
| This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. |
| |
| config XILINX_EMACLITE |
| depends on DM_ETH |
| select PHYLIB |
| select MII |
| bool "Xilinx Ethernetlite" |
| help |
| This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. |
| |
| config ZYNQ_GEM |
| depends on DM_ETH |
| select PHYLIB |
| bool "Xilinx Ethernet GEM" |
| help |
| This MAC is present in Xilinx Zynq and ZynqMP SoCs. |
| |
| config PIC32_ETH |
| bool "Microchip PIC32 Ethernet Support" |
| depends on DM_ETH && MACH_PIC32 |
| select PHYLIB |
| help |
| This driver implements 10/100 Mbps Ethernet and MAC layer for |
| Microchip PIC32 microcontrollers. |
| |
| config GMAC_ROCKCHIP |
| bool "Rockchip Synopsys Designware Ethernet MAC" |
| depends on DM_ETH && ETH_DESIGNWARE |
| help |
| This driver provides Rockchip SoCs network support based on the |
| Synopsys Designware driver. |
| |
| config RENESAS_RAVB |
| bool "Renesas Ethernet AVB MAC" |
| depends on DM_ETH && RCAR_GEN3 |
| select PHYLIB |
| help |
| This driver implements support for the Ethernet AVB block in |
| Renesas M3 and H3 SoCs. |
| |
| config MPC8XX_FEC |
| bool "Fast Ethernet Controller on MPC8XX" |
| depends on MPC8xx |
| select MII |
| help |
| This driver implements support for the Fast Ethernet Controller |
| on MPC8XX |
| |
| config SNI_AVE |
| bool "Socionext AVE Ethernet support" |
| depends on DM_ETH && ARCH_UNIPHIER |
| select PHYLIB |
| select SYSCON |
| select REGMAP |
| help |
| This driver implements support for the Socionext AVE Ethernet |
| controller, as found on the Socionext UniPhier family. |
| |
| source "drivers/net/mscc_eswitch/Kconfig" |
| |
| config ETHER_ON_FEC1 |
| bool "FEC1" |
| depends on MPC8XX_FEC |
| default y |
| |
| config FEC1_PHY |
| int "FEC1 PHY" |
| depends on ETHER_ON_FEC1 |
| default -1 |
| help |
| Define to the hardcoded PHY address which corresponds |
| to the given FEC; i. e. |
| #define CONFIG_FEC1_PHY 4 |
| means that the PHY with address 4 is connected to FEC1 |
| |
| When set to -1, means to probe for first available. |
| |
| config PHY_NORXERR |
| bool "PHY_NORXERR" |
| depends on ETHER_ON_FEC1 |
| default n |
| help |
| The PHY does not have a RXERR line (RMII only). |
| (so program the FEC to ignore it). |
| |
| config ETHER_ON_FEC2 |
| bool "FEC2" |
| depends on MPC8XX_FEC && MPC885 |
| default y |
| |
| config FEC2_PHY |
| int "FEC2 PHY" |
| depends on ETHER_ON_FEC2 |
| default -1 |
| help |
| Define to the hardcoded PHY address which corresponds |
| to the given FEC; i. e. |
| #define CONFIG_FEC1_PHY 4 |
| means that the PHY with address 4 is connected to FEC1 |
| |
| When set to -1, means to probe for first available. |
| |
| config FEC2_PHY_NORXERR |
| bool "PHY_NORXERR" |
| depends on ETHER_ON_FEC2 |
| default n |
| help |
| The PHY does not have a RXERR line (RMII only). |
| (so program the FEC to ignore it). |
| |
| config SYS_DPAA_QBMAN |
| bool "Device tree fixup for QBMan on freescale SOCs" |
| depends on (ARM || PPC) && !SPL_BUILD |
| default y if ARCH_B4860 || \ |
| ARCH_B4420 || \ |
| ARCH_P1023 || \ |
| ARCH_P2041 || \ |
| ARCH_T1023 || \ |
| ARCH_T1024 || \ |
| ARCH_T1040 || \ |
| ARCH_T1042 || \ |
| ARCH_T2080 || \ |
| ARCH_T2081 || \ |
| ARCH_T4240 || \ |
| ARCH_T4160 || \ |
| ARCH_P4080 || \ |
| ARCH_P3041 || \ |
| ARCH_P5040 || \ |
| ARCH_P5020 || \ |
| ARCH_LS1043A || \ |
| ARCH_LS1046A |
| help |
| QBman fixups to allow deep sleep in DPAA 1 SOCs |
| |
| config TSEC_ENET |
| select PHYLIB |
| bool "Enable Three-Speed Ethernet Controller" |
| help |
| This driver implements support for the (Enhanced) Three-Speed |
| Ethernet Controller found on Freescale SoCs. |
| |
| config MEDIATEK_ETH |
| bool "MediaTek Ethernet GMAC Driver" |
| depends on DM_ETH |
| select PHYLIB |
| select DM_GPIO |
| select DM_RESET |
| help |
| This Driver support MediaTek Ethernet GMAC |
| Say Y to enable support for the MediaTek Ethernet GMAC. |
| |
| config HIGMACV300_ETH |
| bool "HiSilicon Gigabit Ethernet Controller" |
| depends on DM_ETH |
| select DM_RESET |
| select PHYLIB |
| help |
| This driver supports HIGMACV300 Ethernet controller found on |
| HiSilicon SoCs. |
| |
| config FSL_ENETC |
| bool "NXP ENETC Ethernet controller" |
| depends on DM_PCI && DM_ETH && DM_MDIO |
| help |
| This driver supports the NXP ENETC Ethernet controller found on some |
| of the NXP SoCs. |
| |
| config MDIO_MUX_I2CREG |
| bool "MDIO MUX accessed as a register over I2C" |
| depends on DM_MDIO_MUX && DM_I2C |
| help |
| This driver is used for MDIO muxes driven by writing to a register of |
| an I2C chip. The board it was developed for uses a mux controlled by |
| on-board FPGA which in turn is accessed as a chip over I2C. |
| |
| config MVMDIO |
| bool "Marvell MDIO interface support" |
| depends on DM_MDIO |
| help |
| This driver supports the MDIO interface found in the network |
| interface units of the Marvell EBU SoCs (Kirkwood, Orion5x, |
| Dove, Armada 370, Armada XP, Armada 37xx and Armada7K/8K/8KP). |
| |
| This driver is used by the MVPP2 and MVNETA drivers. |
| |
| config FSL_LS_MDIO |
| bool "NXP Layerscape MDIO interface support" |
| depends on DM_MDIO |
| help |
| This driver supports the MDIO bus found on the Fman 10G Ethernet MACs and |
| on the mEMAC (which supports both Clauses 22 and 45). |
| |
| endif # NETDEVICES |