| /* |
| * Copyright (C) 2012 Freescale Semiconductor, Inc. |
| * |
| * Configuration settings for the Freescale i.MX6Q SabreSD board. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __MX6QSABRESD_CONFIG_H |
| #define __MX6QSABRESD_CONFIG_H |
| |
| #ifdef CONFIG_SPL |
| #include "imx6_spl.h" |
| #endif |
| |
| #define CONFIG_MACH_TYPE 3980 |
| #define CONFIG_MXC_UART_BASE UART1_BASE |
| #define CONSOLE_DEV "ttymxc0" |
| #define CONFIG_MMCROOT "/dev/mmcblk1p2" |
| |
| #define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */ |
| |
| #include "mx6sabre_common.h" |
| |
| /* Falcon Mode */ |
| #define CONFIG_SPL_FS_LOAD_ARGS_NAME "args" |
| #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" |
| #define CONFIG_CMD_SPL |
| #define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000 |
| #define CONFIG_CMD_SPL_WRITE_SIZE (128 * SZ_1K) |
| |
| /* Falcon Mode - MMC support: args@1MB kernel@2MB */ |
| #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x800 /* 1MB */ |
| #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512) |
| #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000 /* 2MB */ |
| |
| #define CONFIG_SYS_FSL_USDHC_NUM 3 |
| #if defined(CONFIG_ENV_IS_IN_MMC) |
| #define CONFIG_SYS_MMC_ENV_DEV 1 /* SDHC3 */ |
| #endif |
| |
| #define CONFIG_CMD_PCI |
| #ifdef CONFIG_CMD_PCI |
| #define CONFIG_PCI_SCAN_SHOW |
| #define CONFIG_PCIE_IMX |
| #define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) |
| #define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(3, 19) |
| #endif |
| |
| /* I2C Configs */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_MXC |
| #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ |
| #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ |
| #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ |
| #define CONFIG_SYS_I2C_SPEED 100000 |
| |
| /* PMIC */ |
| #define CONFIG_POWER |
| #define CONFIG_POWER_I2C |
| #define CONFIG_POWER_PFUZE100 |
| #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 |
| |
| /* USB Configs */ |
| #ifdef CONFIG_CMD_USB |
| #define CONFIG_USB_EHCI |
| #define CONFIG_USB_EHCI_MX6 |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| #define CONFIG_USB_HOST_ETHER |
| #define CONFIG_USB_ETHER_ASIX |
| #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) |
| #define CONFIG_MXC_USB_FLAGS 0 |
| #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 /* Enabled USB controller number */ |
| #endif |
| |
| #endif /* __MX6QSABRESD_CONFIG_H */ |