blob: d658fac02c8ff1116c1b4174ff7e38496d69bebe [file] [log] [blame]
.. SPDX-License-Identifier: GPL-2.0+
.. sectionauthor:: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Edison
======
Build Instructions for U-Boot as main bootloader
------------------------------------------------
Simple you can build U-Boot and obtain u-boot.bin::
$ make edison_defconfig
$ make all
Updating U-Boot on Edison
-------------------------
By default Intel Edison boards are shipped with preinstalled heavily
patched U-Boot v2014.04. Though it supports DFU which we may be able to
use.
1. Prepare u-boot.bin as described in chapter above. You still need one
more step (if and only if you have original U-Boot), i.e. run the
following command::
$ truncate -s %4096 u-boot.bin
2. Run your board and interrupt booting to U-Boot console. In the console
call::
=> run do_force_flash_os
3. Wait for few seconds, it will prepare environment variable and runs
DFU. Run DFU command from the host system::
$ dfu-util -v -d 8087:0a99 --alt u-boot0 -D u-boot.bin
4. Return to U-Boot console and following hint. i.e. push Ctrl+C, and
reset the board::
=> reset
Updating U-Boot using xFSTK
---------------------------
You can also update U-Boot using the xfstk-dldr-solo tool if you can build it.
One way to do that is to follow the `xFSTK`_ instructions. You may need to use
a virtual machine running Ubuntu Trusty. Once you have built it and installed
libboost-all-dev, you can copy xfstk-dldr-solo to /usr/local/bin and
libboost_program_options.so.1.54.0 to /usr/lib/i386-linux-gnu/ and with luck
it will work. You might fine this `drive`_ helpful.
If it does, then you can download and unpack the Edison reocovery image,
install dfu-util, reset your board and flash U-Boot like this::
$ xfstk-dldr-solo --gpflags 0x80000007 \
--osimage u-boot-edison.img \
--fwdnx recover/edison_dnx_fwr.bin \
--fwimage recover/edison_ifwi-dbg-00.bin \
--osdnx recover/edison_dnx_osr.bin
This should show the following
.. code-block:: none
XFSTK Downloader Solo 0.0.0
Copyright (c) 2015 Intel Corporation
Build date and time: Aug 15 2020 15:07:13
.Intel SoC Device Detection Found
Parsing Commandline....
Registering Status Callback....
.Initiating Download Process....
.......(lots of dots)........XFSTK-STATUS--Reconnecting to device - Attempt #1
.......(even more dots)......................
You have about 10 seconds after resetting the board to type the above command.
If you want to check if the board is ready, type:
.. code-block:: none
lsusb |egrep "8087|8086"
Bus 001 Device 004: ID 8086:e005 Intel Corp.
If you see a device with the same ID as above, the board is waiting for your
command.
After about 5 seconds you should see some console output from the board:
.. code-block:: none
******************************
PSH KERNEL VERSION: b0182b2b
WR: 20104000
******************************
SCU IPC: 0x800000d0 0xfffce92c
PSH miaHOB version: TNG.B0.VVBD.0000000c
microkernel built 11:24:08 Feb 5 2015
******* PSH loader *******
PCM page cache size = 192 KB
Cache Constraint = 0 Pages
Arming IPC driver ..
Adding page store pool ..
PagestoreAddr(IMR Start Address) = 0x04899000
pageStoreSize(IMR Size) = 0x00080000
*** Ready to receive application ***
After another 10 seconds the xFSTK tool completes and the board resets. About
10 seconds after that should see the above message again and then within a
few seconds U-Boot should start on your board:
.. code-block:: none
U-Boot 2020.10-rc3 (Sep 03 2020 - 18:44:28 -0600)
CPU: Genuine Intel(R) CPU 4000 @ 500MHz
DRAM: 980.6 MiB
WDT: Started with servicing (60s timeout)
MMC: mmc@ff3fc000: 0, mmc@ff3fa000: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Saving Environment to MMC... Writing to redundant MMC(0)... OK
Saving Environment to MMC... Writing to MMC(0)... OK
Net: No ethernet found.
Hit any key to stop autoboot: 0
Target:blank
Partitioning using GPT
Writing GPT: success!
Saving Environment to MMC... Writing to redundant MMC(0)... OK
Flashing already done...
5442816 bytes read in 238 ms (21.8 MiB/s)
Valid Boot Flag
Setup Size = 0x00003c00
Magic signature found
Using boot protocol version 2.0c
Linux kernel version 3.10.17-poky-edison+ (ferry@kalamata) #1 SMP PREEMPT Mon Jan 11 14:54:18 CET 2016
Building boot_params at 0x00090000
Loading bzImage at address 100000 (5427456 bytes)
Magic signature found
Kernel command line: "rootwait root=PARTUUID=ada722ed-6410-764e-8619-abff6f66e10e rootfstype=ext4 console=ttyMFD2 earlyprintk=ttyMFD2,keep loglevel=4 g_multi.ethernet_config=cdc systemd.unit=multi-user.target hardware_id=00 g_multi.iSerialNumber=2249baf774c675598661a63098c0ad41 g_multi.dev_addr=02:00:86:c0:ad:41 platform_mrfld_audio.audio_codec=dummy"
Magic signature found
Starting kernel ...
...
Poky (Yocto Project Reference Distro) 1.7.2 edison ttyMFD2
edison login:
.. _xFSTK: https://community.intel.com/t5/Intel-Makers/Building-xFSTK-on-Ubuntu-14-04-32-bit-for-flashing-Edison/td-p/538081
.. _drive: https://drive.google.com/drive/u/0/folders/1URPHrOk9-UBsh8hjv-7WwC0W6Fy61uAJ