| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Marvell / Cavium Inc. CN73xx |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/clock/octeon-clock.h> |
| |
| / { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| soc0: soc@0 { |
| interrupt-parent = <&ciu3>; |
| compatible = "simple-bus"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; /* Direct mapping */ |
| |
| ciu3: interrupt-controller@1010000000000 { |
| compatible = "cavium,octeon-7890-ciu3"; |
| interrupt-controller; |
| /* |
| * Interrupts are specified by two parts: |
| * 1) Source number (20 significant bits) |
| * 2) Trigger type: (4 == level, 1 == edge) |
| */ |
| #address-cells = <0>; |
| #interrupt-cells = <2>; |
| reg = <0x10100 0x00000000 0x0 0xb0000000>; |
| }; |
| |
| bootbus: bootbus@1180000000000 { |
| compatible = "cavium,octeon-3860-bootbus","simple-bus"; |
| reg = <0x11800 0x00000000 0x0 0x200>; |
| /* The chip select number and offset */ |
| #address-cells = <2>; |
| /* The size of the chip select region */ |
| #size-cells = <1>; |
| }; |
| |
| clk: clock { |
| compatible = "mrvl,octeon-clk"; |
| #clock-cells = <1>; |
| bootph-all; |
| }; |
| |
| gpio: gpio-controller@1070000000800 { |
| #gpio-cells = <2>; |
| compatible = "cavium,octeon-7890-gpio"; |
| reg = <0x10700 0x00000800 0x0 0x100>; |
| gpio-controller; |
| nr-gpios = <32>; |
| /* Interrupts are specified by two parts: |
| * 1) GPIO pin number (0..15) |
| * 2) Triggering (1 - edge rising |
| * 2 - edge falling |
| * 4 - level active high |
| * 8 - level active low) |
| */ |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| /* The GPIO pins connect to 16 consecutive CUI bits */ |
| interrupts = <0x03000 4>, <0x03001 4>, |
| <0x03002 4>, <0x03003 4>, |
| <0x03004 4>, <0x03005 4>, |
| <0x03006 4>, <0x03007 4>, |
| <0x03008 4>, <0x03009 4>, |
| <0x0300a 4>, <0x0300b 4>, |
| <0x0300c 4>, <0x0300d 4>, |
| <0x0300e 4>, <0x0300f 4>; |
| }; |
| |
| l2c: l2c@1180080000000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "cavium,octeon-7xxx-l2c"; |
| reg = <0x11800 0x80000000 0x0 0x01000000>; |
| bootph-all; |
| }; |
| |
| lmc: lmc@1180088000000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "cavium,octeon-7xxx-ddr4"; |
| reg = <0x11800 0x88000000 0x0 0x02000000>; // 2 IFs |
| bootph-all; |
| l2c-handle = <&l2c>; |
| }; |
| |
| reset: reset@1180006001600 { |
| compatible = "mrvl,cn7xxx-rst"; |
| reg = <0x11800 0x06001600 0x0 0x200>; |
| }; |
| |
| uart0: serial@1180000000800 { |
| compatible = "cavium,octeon-3860-uart","ns16550"; |
| reg = <0x11800 0x00000800 0x0 0x400>; |
| clocks = <&clk OCTEON_CLK_IO>; |
| clock-frequency = <0>; |
| current-speed = <115200>; |
| reg-shift = <3>; |
| interrupts = <0x08000 4>; |
| }; |
| |
| uart1: serial@1180000000c00 { |
| compatible = "cavium,octeon-3860-uart","ns16550"; |
| reg = <0x11800 0x00000c00 0x0 0x400>; |
| clocks = <&clk OCTEON_CLK_IO>; |
| clock-frequency = <0>; |
| current-speed = <115200>; |
| reg-shift = <3>; |
| interrupts = <0x08040 4>; |
| }; |
| |
| i2c0: i2c@1180000001000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "cavium,octeon-7890-twsi"; |
| reg = <0x11800 0x00001000 0x0 0x200>; |
| /* INT_ST, INT_TS, INT_CORE */ |
| interrupts = <0x0b000 1>, <0x0b001 1>, <0x0b002 1>; |
| clock-frequency = <100000>; |
| clocks = <&clk OCTEON_CLK_IO>; |
| }; |
| |
| i2c1: i2c@1180000001200 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "cavium,octeon-7890-twsi"; |
| reg = <0x11800 0x00001200 0x0 0x200>; |
| /* INT_ST, INT_TS, INT_CORE */ |
| interrupts = <0x0b100 1>, <0x0b101 1>, <0x0b102 1>; |
| clock-frequency = <100000>; |
| clocks = <&clk OCTEON_CLK_IO>; |
| }; |
| |
| mmc: mmc@1180000002000 { |
| compatible = "cavium,octeon-7890-mmc", |
| "cavium,octeon-7360-mmc"; |
| reg = <0x11800 0x00000000 0x0 0x2100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| /* EMM_INT_BUF_DONE, |
| EMM_INT_CMD_DONE, |
| EMM_INT_DMA_DONE, |
| EMM_INT_CMD_ERR, |
| EMM_INT_DMA_ERR, |
| EMM_INT_SWITCH_DONE, |
| EMM_INT_SWITCH_ERR, |
| EMM_DMA_DONE, |
| EMM_DMA_FIFO*/ |
| interrupts = <0x09040 1>, |
| <0x09041 1>, |
| <0x09042 1>, |
| <0x09043 1>, |
| <0x09044 1>, |
| <0x09045 1>, |
| <0x09046 1>, |
| <0x09000 1>, |
| <0x09001 1>; |
| clocks = <&clk OCTEON_CLK_IO>; |
| }; |
| |
| spi: spi@1070000001000 { |
| compatible = "cavium,octeon-3010-spi"; |
| reg = <0x10700 0x00001000 0x0 0x100>; |
| interrupts = <0x05001 1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| spi-max-frequency = <25000000>; |
| clocks = <&clk OCTEON_CLK_IO>; |
| }; |
| |
| /* USB 0 */ |
| usb0: uctl@1180068000000 { |
| compatible = "cavium,octeon-7130-usb-uctl"; |
| reg = <0x11800 0x68000000 0x0 0x100>; |
| ranges; /* Direct mapping */ |
| #address-cells = <2>; |
| #size-cells = <2>; |
| /* Only 100MHz allowed */ |
| refclk-frequency = <100000000>; |
| /* Only "dlmc_ref_clk0" is supported for 73xx */ |
| refclk-type-ss = "dlmc_ref_clk0"; |
| /* Only "dlmc_ref_clk0" is supported for 73xx */ |
| refclk-type-hs = "dlmc_ref_clk0"; |
| |
| /* |
| * Power is specified by three parts: |
| * 1) GPIO handle (must be &gpio) |
| * 2) GPIO pin number |
| * 3) Active high (0) or active low (1) |
| */ |
| xhci@1680000000000 { |
| compatible = "cavium,octeon-7130-xhci","synopsys,dwc3","snps,dwc3"; |
| reg = <0x16800 0x00000000 0x10 0x0>; |
| interrupts = <0x68080 4>; /* UAHC_IMAN, level */ |
| maximum-speed = "super-speed"; |
| dr_mode = "host"; |
| snps,dis_u3_susphy_quirk; |
| snps,dis_u2_susphy_quirk; |
| snps,dis_enblslpm_quirk; |
| }; |
| }; |
| |
| /* USB 1 */ |
| usb1: uctl@1180069000000 { |
| compatible = "cavium,octeon-7130-usb-uctl"; |
| reg = <0x11800 0x69000000 0x0 0x100>; |
| ranges; /* Direct mapping */ |
| #address-cells = <2>; |
| #size-cells = <2>; |
| /* 50MHz, 100MHz and 125MHz allowed */ |
| refclk-frequency = <100000000>; |
| /* Either "dlmc_ref_clk0" or "dlmc_ref_clk0" */ |
| refclk-type-ss = "dlmc_ref_clk0"; |
| /* Either "dlmc_ref_clk0" "dlmc_ref_clk1" or "pll_ref_clk" */ |
| refclk-type-hs = "dlmc_ref_clk0"; |
| |
| /* |
| * Power is specified by three parts: |
| * 1) GPIO handle (must be &gpio) |
| * 2) GPIO pin number |
| * 3) Active high (0) or active low (1) |
| */ |
| xhci@1690000000000 { |
| compatible = "cavium,octeon-7130-xhci","synopsys,dwc3","snps,dwc3"; |
| reg = <0x16900 0x00000000 0x10 0x0>; |
| interrupts = <0x69080 4>; /* UAHC_IMAN, level */ |
| dr_mode = "host"; |
| }; |
| }; |
| |
| /* PCIe 0 */ |
| pcie0: pcie@1180069000000 { |
| compatible = "marvell,pcie-host-octeon"; |
| reg = <0 0xf2600000 0 0x10000>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| dma-coherent; |
| |
| bus-range = <0 0xff>; |
| marvell,pcie-port = <0>; |
| ranges = <0x81000000 0x00000000 0xd0000000 0x00011a00 0xd0000000 0x00000000 0x01000000 /* IO */ |
| 0x02000000 0x00000000 0xe0000000 0x00011b00 0xe0000000 0x00000000 0x10000000 /* non-prefetchable memory */ |
| 0x43000000 0x00011c00 0x00000000 0x00011c00 0x00000000 0x00000010 0x00000000>;/* prefetchable memory */ |
| }; |
| |
| uctl@118006c000000 { |
| compatible = "cavium,octeon-7130-sata-uctl", "simple-bus"; |
| reg = <0x11800 0x6c000000 0x0 0x100>; |
| ranges; /* Direct mapping */ |
| #address-cells = <2>; |
| #size-cells = <2>; |
| portmap = <0x3>; |
| staggered-spinup; |
| cavium,qlm-trim = "4,sata"; |
| |
| sata: sata@16c0000000000 { |
| compatible = "cavium,octeon-7130-ahci"; |
| reg = <0x16c00 0x00000000 0x0 0x200>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| interrupts = <0x6c010 4>; |
| }; |
| }; |
| |
| /* SMI1 */ |
| smi1: mdio@1180000003880 { |
| compatible = "cavium,octeon-3860-mdio"; |
| reg = <0x11800 0x00003880 0x0 0x40>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| /* BGX 0 */ |
| bgx0: ethernet-mac-nexus@11800e0000000 { |
| compatible = "cavium,octeon-7890-bgx"; |
| reg = <0x11800 0xe0000000 0x0 0x1000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| /* BGX 1 */ |
| bgx1: ethernet-mac-nexus@11800e1000000 { |
| compatible = "cavium,octeon-7890-bgx"; |
| reg = <0x11800 0xe1000000 0x0 0x1000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| /* BGX 2*/ |
| bgx2: ethernet-mac-nexus@11800e2000000 { |
| compatible = "cavium,octeon-7890-bgx"; |
| reg = <0x11800 0xe2000000 0x0 0x1000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| }; |