include/configs/mccmon6.h - platform/external/u-boot - Gitiles

 /*
  * Copyright (C) 2016-2017
  * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #include <config_distro_defaults.h>
 #include "mx6_common.h"

 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #include "imx6_spl.h"

 #define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + 0x80000)
 #define CONFIG_SPL_OS_BOOT
 #define CONFIG_SYS_OS_BASE (CONFIG_SYS_FLASH_BASE + 0x180000)
 #define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + 0x1980000)
 #define CONFIG_SYS_FDT_SIZE (48 * SZ_1K)
 #define CONFIG_SYS_SPL_ARGS_ADDR	0x18000000

 /*
  * Below defines are set but NOT really used since we by
  * design force U-Boot run when we boot in development
  * mode from SD card (SD2)
  */
 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR (0x800)
 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (0x80)
 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR (0x1000)
 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "imx6q-mccmon.dtb"

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)

 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_LATE_INIT

 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE		UART1_BASE

 #define CONFIG_SYS_MEMTEST_START	0x10000000
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)

 #define CONFIG_MXC_SPI
 #define CONFIG_SF_DEFAULT_BUS  2
 #define CONFIG_SF_DEFAULT_CS   0
 #define CONFIG_SF_DEFAULT_SPEED 25000000
 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)

 /* I2C Configs */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
 #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
 #define CONFIG_SYS_I2C_SPEED		100000

 /* MMC Configuration */
 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #define CONFIG_SYS_FSL_ESDHC_ADDR	0

 #undef CONFIG_SYS_NO_FLASH
 /* NOR 16-bit mode */
 #define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
 #define CONFIG_SYS_FLASH_PROTECTION
 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
 #define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
 #define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_FLASH_CFI_DRIVER         /* Use drivers/cfi_flash.c */
 #define CONFIG_FLASH_VERIFY

 /* NOR Flash MTD */
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_FLASH_CFI_MTD
 #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
 #define CONFIG_SYS_FLASH_BANKS_LIST	{ (CONFIG_SYS_FLASH_BASE) }
 #define CONFIG_SYS_FLASH_BANKS_SIZES	{ (32 * SZ_1M) }

 /* MTD support */
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS

 #define MTDIDS_DEFAULT                  "nor0=8000000.nor"
 #define MTDPARTS_DEFAULT  \
 	"mtdparts=8000000.nor:" \
 	"32m@0x0(mccmon6-image.nor)," \
 	"256k@0x40000(u-boot-env.nor)," \
 	"1m@0x80000(u-boot.nor)," \
 	"8m@0x180000(kernel.nor)," \
 	"8m@0x980000(swupdate-kernel.nor)," \
 	"8m@0x1180000(swupdate-rootfs.nor)," \
 	"128k@0x1980000(kernel-dtb.nor)," \
 	"128k@0x19C0000(swupdate-kernel-dtb.nor)"

 /* USB Configs */
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_MX6
 #define CONFIG_USB_STORAGE
 #define CONFIG_USB_MAX_CONTROLLER_COUNT	2
 #define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_MXC_USB_FLAGS		0

 /* Ethernet Configuration */
 #define CONFIG_FEC_MXC
 #define CONFIG_MII
 #define IMX_FEC_BASE			ENET_BASE_ADDR
 #define CONFIG_FEC_XCV_TYPE		RGMII
 #define CONFIG_ETHPRIME			"FEC"
 #define CONFIG_FEC_MXC_PHYADDR		1
 #define CONFIG_PHYLIB
 #define CONFIG_PHY_MICREL
 #define CONFIG_PHY_MICREL_KSZ9031

 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"console=ttymxc0,115200\0" \
 	"fdtfile=imx6q-mccmon6.dtb\0" \
 	"fdt_high=0xffffffff\0" \
 	"initrd_high=0xffffffff\0" \
 	"boot_os=yes\0" \
 	"download_kernel=" \
 		"tftpboot ${kernel_addr} ${kernel_file};" \
 		"tftpboot ${fdt_addr} ${fdtfile};\0" \
 	"get_boot_medium=" \
 		"setenv boot_medium nor;" \
 		"setexpr.l _src_sbmr1 *0x020d8004;" \
 		"setexpr _b_medium ${_src_sbmr1} '&' 0x00000040;" \
 		"if test ${_b_medium} = 40; then " \
 			"setenv boot_medium sdcard;" \
 		"fi\0" \
 	"kernel_file=uImage\0" \
 	"load_kernel=" \
 		"load mmc ${bootdev}:${bootpart} ${kernel_addr} uImage;" \
 		"load mmc ${bootdev}:${bootpart} ${fdt_addr} ${fdtfile};\0" \
 	"boot_sd=" \
 		"echo '#######################';" \
 		"echo '# Factory SDcard Boot #';" \
 		"echo '#######################';" \
 		"setenv mmcdev 1;" \
 		"setenv mmcfactorydev 0;" \
 		"setenv mmcfactorypart 1;" \
 		"run factory_flash_img;\0" \
 	"boot_nor=" \
 		"setenv kernelnor 0x08180000;" \
 		"setenv dtbnor 0x09980000;" \
 		"setenv bootargs console=${console} quiet " \
 		""MTDPARTS_DEFAULT" " \
 		"root=/dev/mmcblk1 rootfstype=ext4 rw rootwait noinitrd;" \
 		"cp.l ${dtbnor} ${dtbloadaddr} 0x8000;" \
 		"bootm ${kernelnor} - ${dtbloadaddr};\0" \
 	"boot_recovery=" \
 		"echo '#######################';" \
 		"echo '# RECOVERY SWU Boot   #';" \
 		"echo '#######################';" \
 		"setenv rootfsloadaddr 0x13000000;" \
 		"setenv swukernelnor 0x08980000;" \
 		"setenv swurootfsnor 0x09180000;" \
 		"setenv swudtbnor 0x099A0000;" \
 		"setenv bootargs console=${console} " \
 		""MTDPARTS_DEFAULT" " \
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
 		    ":${hostname}::off root=/dev/ram rw;" \
 		"cp.l ${swurootfsnor} ${rootfsloadaddr} 0x200000;" \
 		"cp.l ${swudtbnor} ${dtbloadaddr} 0x8000;" \
 		"bootm ${swukernelnor} ${rootfsloadaddr} ${dtbloadaddr};\0" \
 	"boot_tftp=" \
 		"echo '#######################';" \
 		"echo '# TFTP Boot           #';" \
 		"echo '#######################';" \
 		"if run download_kernel; then " \
 		     "setenv bootargs console=${console} " \
 		     "root=/dev/mmcblk0p2 rootwait;" \
 		     "bootm ${kernel_addr} - ${fdt_addr};" \
 		"fi\0" \
 	"bootcmd=" \
 		"if test -n ${recovery_status}; then " \
 		     "run boot_recovery;" \
 		"else " \
 		     "if test ! -n ${boot_medium}; then " \
 			  "run get_boot_medium;" \
 			  "if test ${boot_medium} = sdcard; then " \
 			      "run boot_sd;" \
 			  "else " \
 			      "run boot_nor;" \
 			  "fi;" \
 		     "else " \
 			  "if test ${boot_medium} = tftp; then " \
 			      "run boot_tftp;" \
 			  "fi;" \
 		     "fi;" \
 		"fi\0" \
 	"mtdparts=" MTDPARTS_DEFAULT "\0" \
 	"fdt_addr=0x18000000\0" \
 	"bootdev=1\0" \
 	"bootpart=1\0" \
 	"kernel_addr=" __stringify(CONFIG_LOADADDR) "\0" \
 	"netdev=eth0\0" \
 	"load_addr=0x11000000\0" \
 	"dtbloadaddr=0x12000000\0" \
 	"uboot_file=u-boot.img\0" \
 	"SPL_file=SPL\0" \
 	"load_uboot=tftp ${load_addr} ${uboot_file}\0" \
 	"nor_img_addr=0x11000000\0" \
 	"nor_img_file=core-image-lwn-mccmon6.nor\0" \
 	"emmc_img_file=core-image-lwn-mccmon6.ext4\0" \
 	"nor_bank_start=" __stringify(CONFIG_SYS_FLASH_BASE) "\0" \
 	"nor_img_size=0x02000000\0" \
 	"factory_script_file=factory.scr\0" \
 	"factory_load_script=" \
 		"if test -e mmc ${mmcdev}:${mmcfactorypart} " \
 		    "${factory_script_file}; then " \
 		    "load mmc ${mmcdev}:${mmcfactorypart} " \
 		     "${loadaddr} ${factory_script_file};" \
 		"fi\0" \
 	"factory_script=echo Running factory script from mmc${mmcdev} ...; " \
 		"source ${loadaddr}\0" \
 	"factory_flash_img="\
 		"echo 'Flash mccmon6 with factory images'; " \
 		"if run factory_load_script; then " \
 			"run factory_script;" \
 		"else " \
 		    "echo No factory script: ${factory_script_file} found on " \
 		    "device ${mmcdev};" \
 		    "run factory_nor_img;" \
 		    "run factory_eMMC_img;" \
 		"fi\0" \
 	"factory_eMMC_img="\
 		"echo 'Update mccmon6 eMMC image'; " \
 		"if load mmc ${mmcdev}:${mmcfactorypart} " \
 		    "${loadaddr} ${emmc_img_file}; then " \
 		    "setexpr fw_sz ${filesize} / 0x200;" \
 		    "setexpr fw_sz ${fw_sz} + 1;" \
 		    "mmc dev ${mmcfactorydev};" \
 		    "mmc write ${loadaddr} 0x0 ${fw_sz};" \
 		"fi\0" \
 	"factory_nor_img="\
 		"echo 'Update mccmon6 NOR image'; " \
 		"if load mmc ${mmcdev}:${mmcfactorypart} " \
 		    "${nor_img_addr} ${nor_img_file}; then " \
 			"run nor_update;" \
 		"fi\0" \
 	"nor_update=" \
 		    "protect off ${nor_bank_start} +${nor_img_size};" \
 		    "erase ${nor_bank_start} +${nor_img_size};" \
 		    "setexpr nor_img_size ${nor_img_size} / 4; " \
 		    "cp.l ${nor_img_addr} ${nor_bank_start} ${nor_img_size}\0" \
 	"tftp_nor_uboot="\
 		"echo 'Update mccmon6 NOR U-BOOT via TFTP'; " \
 		"setenv nor_img_file u-boot.img; " \
 		"setenv nor_img_size 0x80000; " \
 		"setenv nor_bank_start 0x08080000; " \
 		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
 		    "run nor_update;" \
 		"fi\0" \
 	"tftp_nor_uImg="\
 		"echo 'Update mccmon6 NOR uImage via TFTP'; " \
 		"setenv nor_img_file uImage; " \
 		"setenv nor_img_size 0x500000; " \
 		"setenv nor_bank_start 0x08180000; " \
 		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
 		    "run nor_update;" \
 		"fi\0" \
 	"tftp_nor_img="\
 		"echo 'Update mccmon6 NOR image via TFTP'; " \
 		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
 		    "run nor_update;" \
 		"fi\0" \
 	"tftp_nor_SPL="\
 		"if tftp ${load_addr} SPL_padded; then " \
 		    "erase 0x08000000 +0x20000;" \
 		    "cp.b ${load_addr} 0x08000000 0x20000;" \
 		"fi;\0" \
 	"tftp_sd_SPL="\
 	    "if mmc dev 1; then "      \
 		"if tftp ${load_addr} ${SPL_file}; then " \
 		    "setexpr fw_sz ${filesize} / 0x200; " \
 		    "setexpr fw_sz ${fw_sz} + 1; " \
 		    "mmc write ${load_addr} 0x2 ${fw_sz};" \
 		"fi;" \
 	    "fi;\0" \
 	"tftp_sd_uboot="\
 	    "if mmc dev 1; then "      \
 		"if run load_uboot; then " \
 		    "setexpr fw_sz ${filesize} / 0x200; " \
 		    "setexpr fw_sz ${fw_sz} + 1; " \
 		    "mmc write ${load_addr} 0x8A ${fw_sz};" \
 		"fi;" \
 	    "fi;\0"

 /* Physical Memory Map */
 #define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR

 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
 #define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

 #define CONFIG_SYS_INIT_SP_OFFSET \
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

 /* Environment organization */
 #define CONFIG_ENV_SIZE			(SZ_128K)

 /* Envs are stored in NOR flash */
 #define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_SECT_SIZE    (SZ_128K)
 #define CONFIG_ENV_ADDR	(CONFIG_SYS_FLASH_BASE + 0x40000)

 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_SYS_FLASH_BASE + 0x60000)
 #define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE

 #endif			       /* __CONFIG_H * */
	/*
	* Copyright (C) 2016-2017
	* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#include <config_distro_defaults.h>
	#include "mx6_common.h"

	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	#include "imx6_spl.h"

	#define CONFIG_SPL_BOARD_INIT
	#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + 0x80000)
	#define CONFIG_SPL_OS_BOOT
	#define CONFIG_SYS_OS_BASE (CONFIG_SYS_FLASH_BASE + 0x180000)
	#define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + 0x1980000)
	#define CONFIG_SYS_FDT_SIZE (48 * SZ_1K)
	#define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000

	/*
	* Below defines are set but NOT really used since we by
	* design force U-Boot run when we boot in development
	* mode from SD card (SD2)
	*/
	#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR (0x800)
	#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (0x80)
	#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR (0x1000)
	#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
	#define CONFIG_SPL_FS_LOAD_ARGS_NAME "imx6q-mccmon.dtb"

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)

	#define CONFIG_BOARD_EARLY_INIT_F
	#define CONFIG_BOARD_LATE_INIT

	#define CONFIG_MXC_UART
	#define CONFIG_MXC_UART_BASE UART1_BASE

	#define CONFIG_SYS_MEMTEST_START 0x10000000
	#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)

	#define CONFIG_MXC_SPI
	#define CONFIG_SF_DEFAULT_BUS 2
	#define CONFIG_SF_DEFAULT_CS 0
	#define CONFIG_SF_DEFAULT_SPEED 25000000
	#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)

	/* I2C Configs */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MXC
	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
	#define CONFIG_SYS_I2C_SPEED 100000

	/* MMC Configuration */
	#define CONFIG_SYS_FSL_USDHC_NUM 2
	#define CONFIG_SYS_FSL_ESDHC_ADDR 0

	#undef CONFIG_SYS_NO_FLASH
	/* NOR 16-bit mode */
	#define CONFIG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR
	#define CONFIG_SYS_FLASH_PROTECTION
	#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
	#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
	#define CONFIG_SYS_FLASH_EMPTY_INFO
	#define CONFIG_FLASH_CFI_DRIVER /* Use drivers/cfi_flash.c */
	#define CONFIG_FLASH_VERIFY

	/* NOR Flash MTD */
	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_FLASH_CFI_MTD
	#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
	#define CONFIG_SYS_FLASH_BANKS_LIST { (CONFIG_SYS_FLASH_BASE) }
	#define CONFIG_SYS_FLASH_BANKS_SIZES { (32 * SZ_1M) }

	/* MTD support */
	#define CONFIG_CMD_MTDPARTS
	#define CONFIG_MTD_DEVICE
	#define CONFIG_MTD_PARTITIONS

	#define MTDIDS_DEFAULT "nor0=8000000.nor"
	#define MTDPARTS_DEFAULT \
	"mtdparts=8000000.nor:" \
	"32m@0x0(mccmon6-image.nor)," \
	"256k@0x40000(u-boot-env.nor)," \
	"1m@0x80000(u-boot.nor)," \
	"8m@0x180000(kernel.nor)," \
	"8m@0x980000(swupdate-kernel.nor)," \
	"8m@0x1180000(swupdate-rootfs.nor)," \
	"128k@0x1980000(kernel-dtb.nor)," \
	"128k@0x19C0000(swupdate-kernel-dtb.nor)"

	/* USB Configs */
	#define CONFIG_USB_EHCI
	#define CONFIG_USB_EHCI_MX6
	#define CONFIG_USB_STORAGE
	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
	#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI \| PORT_PTS_PTW)
	#define CONFIG_MXC_USB_FLAGS 0

	/* Ethernet Configuration */
	#define CONFIG_FEC_MXC
	#define CONFIG_MII
	#define IMX_FEC_BASE ENET_BASE_ADDR
	#define CONFIG_FEC_XCV_TYPE RGMII
	#define CONFIG_ETHPRIME "FEC"
	#define CONFIG_FEC_MXC_PHYADDR 1
	#define CONFIG_PHYLIB
	#define CONFIG_PHY_MICREL
	#define CONFIG_PHY_MICREL_KSZ9031

	#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"console=ttymxc0,115200\0" \
	"fdtfile=imx6q-mccmon6.dtb\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"boot_os=yes\0" \
	"download_kernel=" \
	"tftpboot ${kernel_addr} ${kernel_file};" \
	"tftpboot ${fdt_addr} ${fdtfile};\0" \
	"get_boot_medium=" \
	"setenv boot_medium nor;" \
	"setexpr.l _src_sbmr1 *0x020d8004;" \
	"setexpr _b_medium ${_src_sbmr1} '&' 0x00000040;" \
	"if test ${_b_medium} = 40; then " \
	"setenv boot_medium sdcard;" \
	"fi\0" \
	"kernel_file=uImage\0" \
	"load_kernel=" \
	"load mmc ${bootdev}:${bootpart} ${kernel_addr} uImage;" \
	"load mmc ${bootdev}:${bootpart} ${fdt_addr} ${fdtfile};\0" \
	"boot_sd=" \
	"echo '#######################';" \
	"echo '# Factory SDcard Boot #';" \
	"echo '#######################';" \
	"setenv mmcdev 1;" \
	"setenv mmcfactorydev 0;" \
	"setenv mmcfactorypart 1;" \
	"run factory_flash_img;\0" \
	"boot_nor=" \
	"setenv kernelnor 0x08180000;" \
	"setenv dtbnor 0x09980000;" \
	"setenv bootargs console=${console} quiet " \
	""MTDPARTS_DEFAULT" " \
	"root=/dev/mmcblk1 rootfstype=ext4 rw rootwait noinitrd;" \
	"cp.l ${dtbnor} ${dtbloadaddr} 0x8000;" \
	"bootm ${kernelnor} - ${dtbloadaddr};\0" \
	"boot_recovery=" \
	"echo '#######################';" \
	"echo '# RECOVERY SWU Boot #';" \
	"echo '#######################';" \
	"setenv rootfsloadaddr 0x13000000;" \
	"setenv swukernelnor 0x08980000;" \
	"setenv swurootfsnor 0x09180000;" \
	"setenv swudtbnor 0x099A0000;" \
	"setenv bootargs console=${console} " \
	""MTDPARTS_DEFAULT" " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}::off root=/dev/ram rw;" \
	"cp.l ${swurootfsnor} ${rootfsloadaddr} 0x200000;" \
	"cp.l ${swudtbnor} ${dtbloadaddr} 0x8000;" \
	"bootm ${swukernelnor} ${rootfsloadaddr} ${dtbloadaddr};\0" \
	"boot_tftp=" \
	"echo '#######################';" \
	"echo '# TFTP Boot #';" \
	"echo '#######################';" \
	"if run download_kernel; then " \
	"setenv bootargs console=${console} " \
	"root=/dev/mmcblk0p2 rootwait;" \
	"bootm ${kernel_addr} - ${fdt_addr};" \
	"fi\0" \
	"bootcmd=" \
	"if test -n ${recovery_status}; then " \
	"run boot_recovery;" \
	"else " \
	"if test ! -n ${boot_medium}; then " \
	"run get_boot_medium;" \
	"if test ${boot_medium} = sdcard; then " \
	"run boot_sd;" \
	"else " \
	"run boot_nor;" \
	"fi;" \
	"else " \
	"if test ${boot_medium} = tftp; then " \
	"run boot_tftp;" \
	"fi;" \
	"fi;" \
	"fi\0" \
	"mtdparts=" MTDPARTS_DEFAULT "\0" \
	"fdt_addr=0x18000000\0" \
	"bootdev=1\0" \
	"bootpart=1\0" \
	"kernel_addr=" __stringify(CONFIG_LOADADDR) "\0" \
	"netdev=eth0\0" \
	"load_addr=0x11000000\0" \
	"dtbloadaddr=0x12000000\0" \
	"uboot_file=u-boot.img\0" \
	"SPL_file=SPL\0" \
	"load_uboot=tftp ${load_addr} ${uboot_file}\0" \
	"nor_img_addr=0x11000000\0" \
	"nor_img_file=core-image-lwn-mccmon6.nor\0" \
	"emmc_img_file=core-image-lwn-mccmon6.ext4\0" \
	"nor_bank_start=" __stringify(CONFIG_SYS_FLASH_BASE) "\0" \
	"nor_img_size=0x02000000\0" \
	"factory_script_file=factory.scr\0" \
	"factory_load_script=" \
	"if test -e mmc ${mmcdev}:${mmcfactorypart} " \
	"${factory_script_file}; then " \
	"load mmc ${mmcdev}:${mmcfactorypart} " \
	"${loadaddr} ${factory_script_file};" \
	"fi\0" \
	"factory_script=echo Running factory script from mmc${mmcdev} ...; " \
	"source ${loadaddr}\0" \
	"factory_flash_img="\
	"echo 'Flash mccmon6 with factory images'; " \
	"if run factory_load_script; then " \
	"run factory_script;" \
	"else " \
	"echo No factory script: ${factory_script_file} found on " \
	"device ${mmcdev};" \
	"run factory_nor_img;" \
	"run factory_eMMC_img;" \
	"fi\0" \
	"factory_eMMC_img="\
	"echo 'Update mccmon6 eMMC image'; " \
	"if load mmc ${mmcdev}:${mmcfactorypart} " \
	"${loadaddr} ${emmc_img_file}; then " \
	"setexpr fw_sz ${filesize} / 0x200;" \
	"setexpr fw_sz ${fw_sz} + 1;" \
	"mmc dev ${mmcfactorydev};" \
	"mmc write ${loadaddr} 0x0 ${fw_sz};" \
	"fi\0" \
	"factory_nor_img="\
	"echo 'Update mccmon6 NOR image'; " \
	"if load mmc ${mmcdev}:${mmcfactorypart} " \
	"${nor_img_addr} ${nor_img_file}; then " \
	"run nor_update;" \
	"fi\0" \
	"nor_update=" \
	"protect off ${nor_bank_start} +${nor_img_size};" \
	"erase ${nor_bank_start} +${nor_img_size};" \
	"setexpr nor_img_size ${nor_img_size} / 4; " \
	"cp.l ${nor_img_addr} ${nor_bank_start} ${nor_img_size}\0" \
	"tftp_nor_uboot="\
	"echo 'Update mccmon6 NOR U-BOOT via TFTP'; " \
	"setenv nor_img_file u-boot.img; " \
	"setenv nor_img_size 0x80000; " \
	"setenv nor_bank_start 0x08080000; " \
	"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
	"run nor_update;" \
	"fi\0" \
	"tftp_nor_uImg="\
	"echo 'Update mccmon6 NOR uImage via TFTP'; " \
	"setenv nor_img_file uImage; " \
	"setenv nor_img_size 0x500000; " \
	"setenv nor_bank_start 0x08180000; " \
	"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
	"run nor_update;" \
	"fi\0" \
	"tftp_nor_img="\
	"echo 'Update mccmon6 NOR image via TFTP'; " \
	"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
	"run nor_update;" \
	"fi\0" \
	"tftp_nor_SPL="\
	"if tftp ${load_addr} SPL_padded; then " \
	"erase 0x08000000 +0x20000;" \
	"cp.b ${load_addr} 0x08000000 0x20000;" \
	"fi;\0" \
	"tftp_sd_SPL="\
	"if mmc dev 1; then " \
	"if tftp ${load_addr} ${SPL_file}; then " \
	"setexpr fw_sz ${filesize} / 0x200; " \
	"setexpr fw_sz ${fw_sz} + 1; " \
	"mmc write ${load_addr} 0x2 ${fw_sz};" \
	"fi;" \
	"fi;\0" \
	"tftp_sd_uboot="\
	"if mmc dev 1; then " \
	"if run load_uboot; then " \
	"setexpr fw_sz ${filesize} / 0x200; " \
	"setexpr fw_sz ${fw_sz} + 1; " \
	"mmc write ${load_addr} 0x8A ${fw_sz};" \
	"fi;" \
	"fi;\0"

	/* Physical Memory Map */
	#define CONFIG_NR_DRAM_BANKS 1
	#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR

	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE

	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

	/* Environment organization */
	#define CONFIG_ENV_SIZE (SZ_128K)

	/* Envs are stored in NOR flash */
	#define CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_SECT_SIZE (SZ_128K)
	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000)

	#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
	#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + 0x60000)
	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE

	#endif /* __CONFIG_H * */