| CONFIG_ARM=y |
| CONFIG_SKIP_LOWLEVEL_INIT=y |
| CONFIG_ARCH_AT91=y |
| CONFIG_SYS_TEXT_BASE=0x26f00000 |
| CONFIG_TARGET_AT91SAM9N12EK=y |
| CONFIG_NR_DRAM_BANKS=1 |
| CONFIG_ENV_SIZE=0x3000 |
| CONFIG_ENV_OFFSET=0x5000 |
| CONFIG_ENV_SECT_SIZE=0x1000 |
| CONFIG_DM_GPIO=y |
| CONFIG_DEFAULT_DEVICE_TREE="at91sam9n12ek" |
| CONFIG_SYS_PROMPT="U-Boot> " |
| CONFIG_DEBUG_UART_BASE=0xfffff200 |
| CONFIG_DEBUG_UART_CLOCK=132000000 |
| CONFIG_DEBUG_UART_BOARD_INIT=y |
| CONFIG_SYS_LOAD_ADDR=0x22000000 |
| CONFIG_DEBUG_UART=y |
| CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y |
| CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x303f00 |
| CONFIG_SPI_BOOT=y |
| CONFIG_BOOTDELAY=3 |
| CONFIG_USE_BOOTCOMMAND=y |
| CONFIG_BOOTCOMMAND="setenv bootargs ${console} ${mtdparts} ${bootargs_nand};sf probe 0; sf read 0x22000000 0x100000 0x300000; bootm 0x22000000" |
| CONFIG_SYS_CONSOLE_IS_IN_ENV=y |
| # CONFIG_DISPLAY_BOARDINFO is not set |
| CONFIG_HUSH_PARSER=y |
| CONFIG_SYS_CBSIZE=256 |
| CONFIG_SYS_PBSIZE=281 |
| CONFIG_CMD_BOOTZ=y |
| # CONFIG_CMD_FLASH is not set |
| CONFIG_CMD_MMC=y |
| CONFIG_CMD_NAND=y |
| CONFIG_CMD_NAND_TRIMFFS=y |
| # CONFIG_CMD_SETEXPR is not set |
| CONFIG_CMD_DHCP=y |
| CONFIG_BOOTP_BOOTFILESIZE=y |
| CONFIG_CMD_PING=y |
| CONFIG_CMD_FAT=y |
| CONFIG_CMD_MTDPARTS=y |
| CONFIG_MTDIDS_DEFAULT="nand0=atmel_nand" |
| CONFIG_MTDPARTS_DEFAULT="mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs)" |
| CONFIG_OF_CONTROL=y |
| CONFIG_ENV_IS_IN_SPI_FLASH=y |
| CONFIG_SYS_RELOC_GD_ENV_ADDR=y |
| CONFIG_DM=y |
| CONFIG_CLK=y |
| CONFIG_CLK_AT91=y |
| CONFIG_AT91_GPIO=y |
| CONFIG_GENERIC_ATMEL_MCI=y |
| CONFIG_MTD=y |
| CONFIG_MTD_RAW_NAND=y |
| CONFIG_NAND_ATMEL=y |
| CONFIG_ATMEL_NAND_HW_PMECC=y |
| CONFIG_DM_SPI_FLASH=y |
| CONFIG_SF_DEFAULT_SPEED=30000000 |
| CONFIG_SPI_FLASH_ATMEL=y |
| CONFIG_KS8851_MLL=y |
| CONFIG_PINCTRL=y |
| CONFIG_PINCTRL_AT91=y |
| CONFIG_DM_SERIAL=y |
| CONFIG_DEBUG_UART_ANNOUNCE=y |
| CONFIG_ATMEL_USART=y |
| CONFIG_SPI=y |
| CONFIG_DM_SPI=y |
| CONFIG_TIMER=y |
| CONFIG_ATMEL_PIT_TIMER=y |
| CONFIG_USB=y |
| CONFIG_ATMEL_HLCD=y |