| CONFIG_ARM=y |
| CONFIG_SKIP_LOWLEVEL_INIT=y |
| CONFIG_POSITION_INDEPENDENT=y |
| CONFIG_ARCH_SNAPDRAGON=y |
| CONFIG_DEFAULT_DEVICE_TREE="dragonboard845c" |
| CONFIG_SYS_LOAD_ADDR=0x0 |
| CONFIG_FIT=y |
| CONFIG_FIT_VERBOSE=y |
| CONFIG_BOOTSTD_FULL=y |
| # CONFIG_BOOTMETH_EXTLINUX is not set |
| # CONFIG_BOOTMETH_VBE is not set |
| # CONFIG_BOOTMETH_SCRIPT is not set |
| CONFIG_BOOTDELAY=1 |
| CONFIG_USE_PREBOOT=y |
| CONFIG_LOG_MAX_LEVEL=9 |
| CONFIG_LOG_DEFAULT_LEVEL=4 |
| # CONFIG_DISPLAY_CPUINFO is not set |
| CONFIG_DISPLAY_BOARDINFO_LATE=y |
| CONFIG_HUSH_PARSER=y |
| CONFIG_SYS_MAXARGS=64 |
| CONFIG_SYS_CBSIZE=512 |
| CONFIG_CMD_BOOTMENU=y |
| CONFIG_CMD_CLK=y |
| CONFIG_CMD_GPIO=y |
| CONFIG_CMD_MMC=y |
| CONFIG_CMD_PART=y |
| CONFIG_CMD_UFS=y |
| CONFIG_CMD_USB=y |
| CONFIG_CMD_CAT=y |
| CONFIG_CMD_BMP=y |
| CONFIG_CMD_FAT=y |
| CONFIG_CMD_FS_GENERIC=y |
| CONFIG_CMD_LOG=y |
| CONFIG_EFI_PARTITION=y |
| # CONFIG_NET is not set |
| CONFIG_CLK=y |
| CONFIG_CLK_QCOM_QCS404=y |
| CONFIG_CLK_QCOM_SDM845=y |
| CONFIG_MSM_GPIO=y |
| CONFIG_QCOM_PMIC_GPIO=y |
| CONFIG_DM_KEYBOARD=y |
| CONFIG_BUTTON_KEYBOARD=y |
| CONFIG_MMC_SDHCI=y |
| CONFIG_MMC_SDHCI_MSM=y |
| CONFIG_PHY=y |
| CONFIG_PINCTRL=y |
| CONFIG_PINCTRL_QCOM_QCS404=y |
| CONFIG_PINCTRL_QCOM_SDM845=y |
| CONFIG_DM_PMIC=y |
| CONFIG_PMIC_QCOM=y |
| CONFIG_SCSI=y |
| CONFIG_DM_SCSI=y |
| CONFIG_MSM_GENI_SERIAL=y |
| CONFIG_SPMI_MSM=y |
| CONFIG_SYSINFO=y |
| CONFIG_SYSINFO_SMBIOS=y |
| CONFIG_USB=y |
| CONFIG_USB_XHCI_HCD=y |
| CONFIG_USB_XHCI_DWC3=y |
| CONFIG_USB_DWC3=y |
| CONFIG_USB_STORAGE=y |
| CONFIG_UFS=y |
| CONFIG_VIDEO=y |
| # CONFIG_VIDEO_FONT_8X16 is not set |
| CONFIG_VIDEO_FONT_16X32=y |
| CONFIG_SYS_WHITE_ON_BLACK=y |
| CONFIG_NO_FB_CLEAR=y |
| CONFIG_VIDEO_SIMPLE=y |
| CONFIG_HEXDUMP=y |
| # CONFIG_GENERATE_SMBIOS_TABLE is not set |
| CONFIG_LMB_MAX_REGIONS=64 |
| |
| CONFIG_BAUDRATE=115200 |
| |
| # Uncomment to enable UART pre-relocation |
| CONFIG_DEBUG_UART=y |
| CONFIG_DEBUG_UART_ANNOUNCE=y |
| # This is the address of the debug-uart peripheral |
| # The value here is for SDM845, other platforms will vary |
| CONFIG_DEBUG_UART_BASE=0xa84000 |
| # Boards older than ~2018 pre-date the GENI driver and unfortunately |
| # aren't supported here |
| CONFIG_DEBUG_UART_MSM_GENI=y |
| # For sdm845 this is the UART clock rate |
| CONFIG_DEBUG_UART_CLOCK=7372800 |
| # Most newer boards have an oversampling value of 16 instead |
| # of 32, they need the clock rate to be doubled |
| #CONFIG_DEBUG_UART_CLOCK=14745600 |
| |
| CONFIG_LOG=y |
| CONFIG_HEXDUMP=y |
| CONFIG_CMD_LOG=y |
| CONFIG_LOG_MAX_LEVEL=9 |
| CONFIG_LOG_DEFAULT_LEVEL=9 |
| CONFIG_LOGLEVEL=9 |