blob: 4a8acabf72c6261024f801496c0e36bd9186d315 [file] [log] [blame]
/*
* (C) Copyright 2007
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* Configuation settings for the SMN42 board from Siemens.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* If we are developing, we might want to start u-boot from ram
* so we MUST NOT initialize critical regs like mem-timing ...
*/
#undef CONFIG_SKIP_LOWLEVEL_INIT
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_ARM7 1 /* This is a ARM7 CPU */
#define CONFIG_ARM_THUMB 1 /* this is an ARM720TDMI */
#define CONFIG_LPC2292
#undef CONFIG_ARM7_REVD /* disable ARM720 REV.D Workarounds */
#undef CONFIG_USE_IRQ /* don't need them anymore */
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
/*
* Hardware drivers
*/
/*
* select serial console configuration
*/
#define CONFIG_LPC2292_SERIAL
#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
/*
* BOOTP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE
/* enable I2C and select the hardware/software driver */
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
/* this would be 0xAE if E0, E1 and E2 were pulled high */
#define CONFIG_SYS_I2C_SLAVE 0xA0
#define CONFIG_SYS_I2C_EEPROM_ADDR (0xA0 >> 1)
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16 bit address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes per write */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
/* not used but required by devices.c */
#define CONFIG_SYS_I2C_SPEED 10000
#ifdef CONFIG_SOFT_I2C
/*
* Software (bit-bang) I2C driver configuration
*/
#define SCL 0x00000004 /* P0.2 */
#define SDA 0x00000008 /* P0.3 */
#define I2C_READ ((GET32(IO0PIN) & SDA) ? 1 : 0)
#define I2C_SDA(x) { if (x) PUT32(IO0SET, SDA); else PUT32(IO0CLR, SDA); }
#define I2C_SCL(x) { if (x) PUT32(IO0SET, SCL); else PUT32(IO0CLR, SCL); }
#define I2C_DELAY { udelay(100); }
#define I2C_ACTIVE { unsigned int i2ctmp; \
i2ctmp = GET32(IO0DIR); \
i2ctmp |= SDA; \
PUT32(IO0DIR, i2ctmp); }
#define I2C_TRISTATE { unsigned int i2ctmp; \
i2ctmp = GET32(IO0DIR); \
i2ctmp &= ~SDA; \
PUT32(IO0DIR, i2ctmp); }
#endif /* CONFIG_SOFT_I2C */
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_FAT
#define CONFIG_CMD_MMC
#define CONFIG_CMD_NET
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_PING
#define CONFIG_DOS_PARTITION
#define CONFIG_BOOTDELAY 5
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "SMN42 # " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x81800000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x83000000 /* 24 MB in SRAM */
#define CONFIG_SYS_LOAD_ADDR 0x81000000 /* default load address */
/* for uClinux img is here*/
#define CONFIG_SYS_SYS_CLK_FREQ 58982400 /* Hz */
#define CONFIG_SYS_HZ 2048 /* decrementer freq in Hz */
/* valid baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*-----------------------------------------------------------------------
* Stack sizes
*
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
#ifdef CONFIG_USE_IRQ
#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
#endif
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SRAM */
#define PHYS_SDRAM_1 0x81000000 /* SRAM Bank #1 */
#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB SRAM */
/* This is the external flash */
#define PHYS_FLASH_1 0x80000000 /* Flash Bank #1 */
#define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
/*
* The first entry in CONFIG_SYS_FLASH_BANKS_LIST is a dummy, but it must be present.
*/
#define CONFIG_SYS_FLASH_BANKS_LIST { 0, PHYS_FLASH_1 }
#define CONFIG_SYS_FLASH_ADDR0 0x555
#define CONFIG_SYS_FLASH_ADDR1 0x2AA
#define CONFIG_SYS_FLASH_ERASE_TOUT 16384 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CONFIG_ENV_IS_IN_FLASH 1
/* The Environment Sector is in the CPU-internal flash */
#define CONFIG_SYS_FLASH_BASE 0
#define CONFIG_ENV_OFFSET 0x3C000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_MMC 1
/* we use this ethernet chip */
#define CONFIG_ENC28J60_LPC2292
#endif /* __CONFIG_H */