include/spl.h - platform/external/u-boot - Gitiles

 /*
  * (C) Copyright 2012
  * Texas Instruments, <www.ti.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
 #ifndef	_SPL_H_
 #define	_SPL_H_

 /* Platform-specific defines */
 #include <linux/compiler.h>
 #include <asm/spl.h>

 /* Value in r0 indicates we booted from U-Boot */
 #define UBOOT_NOT_LOADED_FROM_SPL	0x13578642

 /* Boot type */
 #define MMCSD_MODE_UNDEFINED	0
 #define MMCSD_MODE_RAW		1
 #define MMCSD_MODE_FS		2
 #define MMCSD_MODE_EMMCBOOT	3

 struct spl_image_info {
 	const char *name;
 	u8 os;
 	ulong load_addr;
 	ulong entry_point;
 	u32 size;
 	u32 flags;
 };

 /*
  * Information required to load data from a device
  *
  * @dev: Pointer to the device, e.g. struct mmc *
  * @priv: Private data for the device
  * @bl_len: Block length for reading in bytes
  * @filename: Name of the fit image file.
  * @read: Function to call to read from the device
  */
 struct spl_load_info {
 	void *dev;
 	void *priv;
 	int bl_len;
 	const char *filename;
 	ulong (*read)(struct spl_load_info *load, ulong sector, ulong count,
 		      void *buf);
 };

 /**
  * spl_load_simple_fit() - Loads a fit image from a device.
  * @spl_image:	Image description to set up
  * @info:	Structure containing the information required to load data.
  * @sector:	Sector number where FIT image is located in the device
  * @fdt:	Pointer to the copied FIT header.
  *
  * Reads the FIT image @sector in the device. Loads u-boot image to
  * specified load address and copies the dtb to end of u-boot image.
  * Returns 0 on success.
  */
 int spl_load_simple_fit(struct spl_image_info *spl_image,
 			struct spl_load_info *info, ulong sector, void *fdt);

 #define SPL_COPY_PAYLOAD_ONLY	1

 /* SPL common functions */
 void preloader_console_init(void);
 u32 spl_boot_device(void);
 u32 spl_boot_mode(const u32 boot_device);

 /**
  * spl_set_header_raw_uboot() - Set up a standard SPL image structure
  *
  * This sets up the given spl_image which the standard values obtained from
  * config options: CONFIG_SYS_MONITOR_LEN, CONFIG_SYS_UBOOT_START,
  * CONFIG_SYS_TEXT_BASE.
  *
  * @spl_image: Image description to set up
  */
 void spl_set_header_raw_uboot(struct spl_image_info *spl_image);

 /**
  * spl_parse_image_header() - parse the image header and set up info
  *
  * This parses the legacy image header information at @header and sets up
  * @spl_image according to what is found. If no image header is found, then
  * a raw image or bootz is assumed. If CONFIG_SPL_PANIC_ON_RAW_IMAGE is
  * enabled, then this causes a panic. If CONFIG_SPL_ABORT_ON_RAW_IMAGE is
  * enabled then U-Boot gives up. Otherwise U-Boot sets up the image using
  * spl_set_header_raw_uboot(), or possibly the bootz header.
  *
  * @spl_image: Image description to set up
  * @header image header to parse
  * @return 0 if a header was correctly parsed, -ve on error
  */
 int spl_parse_image_header(struct spl_image_info *spl_image,
 			   const struct image_header *header);

 void spl_board_prepare_for_linux(void);
 void spl_board_prepare_for_boot(void);
 int spl_board_ubi_load_image(u32 boot_device);

 /**
  * jump_to_image_linux() - Jump to a Linux kernel from SPL
  *
  * This jumps into a Linux kernel using the information in @spl_image.
  *
  * @spl_image: Image description to set up
  * @arg: Argument to pass to Linux (typically a device tree pointer)
  */
 void __noreturn jump_to_image_linux(struct spl_image_info *spl_image,
 				    void *arg);

 /**
  * spl_start_uboot() - Check if SPL should start the kernel or U-Boot
  *
  * This is called by the various SPL loaders to determine whether the board
  * wants to load the kernel or U-Boot. This function should be provided by
  * the board.
  *
  * @return 0 if SPL should start the kernel, 1 if U-Boot must be started
  */
 int spl_start_uboot(void);

 /**
  * spl_display_print() - Display a board-specific message in SPL
  *
  * If CONFIG_SPL_DISPLAY_PRINT is enabled, U-Boot will call this function
  * immediately after displaying the SPL console banner ("U-Boot SPL ...").
  * This function should be provided by the board.
  */
 void spl_display_print(void);

 /**
  * struct spl_boot_device - Describes a boot device used by SPL
  *
  * @boot_device: A number indicating the BOOT_DEVICE type. There are various
  * BOOT_DEVICE... #defines and enums in U-Boot and they are not consistently
  * numbered.
  * @boot_device_name: Named boot device, or NULL if none.
  *
  * Note: Additional fields can be added here, bearing in mind that SPL is
  * size-sensitive and common fields will be present on all boards. This
  * struct can also be used to return additional information about the load
  * process if that becomes useful.
  */
 struct spl_boot_device {
 	uint boot_device;
 	const char *boot_device_name;
 };

 /**
  * Holds information about a way of loading an SPL image
  *
  * @name: User-friendly name for this method (e.g. "MMC")
  * @boot_device: Boot device that this loader supports
  * @load_image: Function to call to load image
  */
 struct spl_image_loader {
 #ifdef CONFIG_SPL_LIBCOMMON_SUPPORT
 	const char *name;
 #endif
 	uint boot_device;
 	/**
 	 * load_image() - Load an SPL image
 	 *
 	 * @spl_image: place to put image information
 	 * @bootdev: describes the boot device to load from
 	 */
 	int (*load_image)(struct spl_image_info *spl_image,
 			  struct spl_boot_device *bootdev);
 };

 /* Declare an SPL image loader */
 #define SPL_LOAD_IMAGE(__name)					\
 	ll_entry_declare(struct spl_image_loader, __name, spl_image_loader)

 /*
  * _priority is the priority of this method, 0 meaning it will be the top
  * choice for this device, 9 meaning it is the bottom choice.
  * _boot_device is the BOOT_DEVICE_... value
  * _method is the load_image function to call
  */
 #ifdef CONFIG_SPL_LIBCOMMON_SUPPORT
 #define SPL_LOAD_IMAGE_METHOD(_name, _priority, _boot_device, _method) \
 	SPL_LOAD_IMAGE(_method ## _priority ## _boot_device) = { \
 		.name = _name, \
 		.boot_device = _boot_device, \
 		.load_image = _method, \
 	}
 #else
 #define SPL_LOAD_IMAGE_METHOD(_name, _priority, _boot_device, _method) \
 	SPL_LOAD_IMAGE(_method ## _priority ## _boot_device) = { \
 		.boot_device = _boot_device, \
 		.load_image = _method, \
 	}
 #endif

 /* SPL FAT image functions */
 int spl_load_image_fat(struct spl_image_info *spl_image,
 		       struct blk_desc *block_dev, int partition,
 		       const char *filename);
 int spl_load_image_fat_os(struct spl_image_info *spl_image,
 			  struct blk_desc *block_dev, int partition);

 void __noreturn jump_to_image_no_args(struct spl_image_info *spl_image);

 /* SPL EXT image functions */
 int spl_load_image_ext(struct spl_image_info *spl_image,
 		       struct blk_desc *block_dev, int partition,
 		       const char *filename);
 int spl_load_image_ext_os(struct spl_image_info *spl_image,
 			  struct blk_desc *block_dev, int partition);

 /**
  * spl_early_init() - Set up device tree and driver model in SPL if enabled
  *
  * Call this function in board_init_f() if you want to use device tree and
  * driver model early, before board_init_r() is called.
  *
  * If this is not called, then driver model will be inactive in SPL's
  * board_init_f(), and no device tree will be available.
  */
 int spl_early_init(void);

 /**
  * spl_init() - Set up device tree and driver model in SPL if enabled
  *
  * You can optionally call spl_early_init(), then optionally call spl_init().
  * This function will be called from board_init_r() if not called earlier.
  *
  * Both spl_early_init() and spl_init() perform a similar function except that
  * the latter will not set up the malloc() area if
  * CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN is enabled, since it is assumed to
  * already be done by a calll to spl_relocate_stack_gd() before board_init_r()
  * is reached.
  *
  * This function will be called from board_init_r() if not called earlier.
  *
  * If this is not called, then driver model will be inactive in SPL's
  * board_init_f(), and no device tree will be available.
  */
 int spl_init(void);

 #ifdef CONFIG_SPL_BOARD_INIT
 void spl_board_init(void);
 #endif

 /**
  * spl_was_boot_source() - check if U-Boot booted from SPL
  *
  * This will normally be true, but if U-Boot jumps to second U-Boot, it will
  * be false. This should be implemented by board-specific code.
  *
  * @return true if U-Boot booted from SPL, else false
  */
 bool spl_was_boot_source(void);

 /**
  * spl_dfu_cmd- run dfu command with chosen mmc device interface
  * @param usb_index - usb controller number
  * @param mmc_dev -  mmc device nubmer
  *
  * @return 0 on success, otherwise error code
  */
 int spl_dfu_cmd(int usbctrl, char *dfu_alt_info, char *interface, char *devstr);

 int spl_mmc_load_image(struct spl_image_info *spl_image,
 		       struct spl_boot_device *bootdev);

 #endif
	/*
	* (C) Copyright 2012
	* Texas Instruments, <www.ti.com>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/
	#ifndef _SPL_H_
	#define _SPL_H_

	/* Platform-specific defines */
	#include <linux/compiler.h>
	#include <asm/spl.h>

	/* Value in r0 indicates we booted from U-Boot */
	#define UBOOT_NOT_LOADED_FROM_SPL 0x13578642

	/* Boot type */
	#define MMCSD_MODE_UNDEFINED 0
	#define MMCSD_MODE_RAW 1
	#define MMCSD_MODE_FS 2
	#define MMCSD_MODE_EMMCBOOT 3

	struct spl_image_info {
	const char *name;
	u8 os;
	ulong load_addr;
	ulong entry_point;
	u32 size;
	u32 flags;
	};

	/*
	* Information required to load data from a device
	*
	* @dev: Pointer to the device, e.g. struct mmc *
	* @priv: Private data for the device
	* @bl_len: Block length for reading in bytes
	* @filename: Name of the fit image file.
	* @read: Function to call to read from the device
	*/
	struct spl_load_info {
	void *dev;
	void *priv;
	int bl_len;
	const char *filename;
	ulong (read)(struct spl_load_info load, ulong sector, ulong count,
	void *buf);
	};

	/**
	* spl_load_simple_fit() - Loads a fit image from a device.
	* @spl_image: Image description to set up
	* @info: Structure containing the information required to load data.
	* @sector: Sector number where FIT image is located in the device
	* @fdt: Pointer to the copied FIT header.
	*
	* Reads the FIT image @sector in the device. Loads u-boot image to
	* specified load address and copies the dtb to end of u-boot image.
	* Returns 0 on success.
	*/
	int spl_load_simple_fit(struct spl_image_info *spl_image,
	struct spl_load_info info, ulong sector, void fdt);

	#define SPL_COPY_PAYLOAD_ONLY 1

	/* SPL common functions */
	void preloader_console_init(void);
	u32 spl_boot_device(void);
	u32 spl_boot_mode(const u32 boot_device);

	/**
	* spl_set_header_raw_uboot() - Set up a standard SPL image structure
	*
	* This sets up the given spl_image which the standard values obtained from
	* config options: CONFIG_SYS_MONITOR_LEN, CONFIG_SYS_UBOOT_START,
	* CONFIG_SYS_TEXT_BASE.
	*
	* @spl_image: Image description to set up
	*/
	void spl_set_header_raw_uboot(struct spl_image_info *spl_image);

	/**
	* spl_parse_image_header() - parse the image header and set up info
	*
	* This parses the legacy image header information at @header and sets up
	* @spl_image according to what is found. If no image header is found, then
	* a raw image or bootz is assumed. If CONFIG_SPL_PANIC_ON_RAW_IMAGE is
	* enabled, then this causes a panic. If CONFIG_SPL_ABORT_ON_RAW_IMAGE is
	* enabled then U-Boot gives up. Otherwise U-Boot sets up the image using
	* spl_set_header_raw_uboot(), or possibly the bootz header.
	*
	* @spl_image: Image description to set up
	* @header image header to parse
	* @return 0 if a header was correctly parsed, -ve on error
	*/
	int spl_parse_image_header(struct spl_image_info *spl_image,
	const struct image_header *header);

	void spl_board_prepare_for_linux(void);
	void spl_board_prepare_for_boot(void);
	int spl_board_ubi_load_image(u32 boot_device);

	/**
	* jump_to_image_linux() - Jump to a Linux kernel from SPL
	*
	* This jumps into a Linux kernel using the information in @spl_image.
	*
	* @spl_image: Image description to set up
	* @arg: Argument to pass to Linux (typically a device tree pointer)
	*/
	void __noreturn jump_to_image_linux(struct spl_image_info *spl_image,
	void *arg);

	/**
	* spl_start_uboot() - Check if SPL should start the kernel or U-Boot
	*
	* This is called by the various SPL loaders to determine whether the board
	* wants to load the kernel or U-Boot. This function should be provided by
	* the board.
	*
	* @return 0 if SPL should start the kernel, 1 if U-Boot must be started
	*/
	int spl_start_uboot(void);

	/**
	* spl_display_print() - Display a board-specific message in SPL
	*
	* If CONFIG_SPL_DISPLAY_PRINT is enabled, U-Boot will call this function
	* immediately after displaying the SPL console banner ("U-Boot SPL ...").
	* This function should be provided by the board.
	*/
	void spl_display_print(void);

	/**
	* struct spl_boot_device - Describes a boot device used by SPL
	*
	* @boot_device: A number indicating the BOOT_DEVICE type. There are various
	* BOOT_DEVICE... #defines and enums in U-Boot and they are not consistently
	* numbered.
	* @boot_device_name: Named boot device, or NULL if none.
	*
	* Note: Additional fields can be added here, bearing in mind that SPL is
	* size-sensitive and common fields will be present on all boards. This
	* struct can also be used to return additional information about the load
	* process if that becomes useful.
	*/
	struct spl_boot_device {
	uint boot_device;
	const char *boot_device_name;
	};

	/**
	* Holds information about a way of loading an SPL image
	*
	* @name: User-friendly name for this method (e.g. "MMC")
	* @boot_device: Boot device that this loader supports
	* @load_image: Function to call to load image
	*/
	struct spl_image_loader {
	#ifdef CONFIG_SPL_LIBCOMMON_SUPPORT
	const char *name;
	#endif
	uint boot_device;
	/**
	* load_image() - Load an SPL image
	*
	* @spl_image: place to put image information
	* @bootdev: describes the boot device to load from
	*/
	int (load_image)(struct spl_image_info spl_image,
	struct spl_boot_device *bootdev);
	};

	/* Declare an SPL image loader */
	#define SPL_LOAD_IMAGE(__name) \
	ll_entry_declare(struct spl_image_loader, __name, spl_image_loader)

	/*
	* _priority is the priority of this method, 0 meaning it will be the top
	* choice for this device, 9 meaning it is the bottom choice.
	* _boot_device is the BOOT_DEVICE_... value
	* _method is the load_image function to call
	*/
	#ifdef CONFIG_SPL_LIBCOMMON_SUPPORT
	#define SPL_LOAD_IMAGE_METHOD(_name, _priority, _boot_device, _method) \
	SPL_LOAD_IMAGE(_method ## _priority ## _boot_device) = { \
	.name = _name, \
	.boot_device = _boot_device, \
	.load_image = _method, \
	}
	#else
	#define SPL_LOAD_IMAGE_METHOD(_name, _priority, _boot_device, _method) \
	SPL_LOAD_IMAGE(_method ## _priority ## _boot_device) = { \
	.boot_device = _boot_device, \
	.load_image = _method, \
	}
	#endif

	/* SPL FAT image functions */
	int spl_load_image_fat(struct spl_image_info *spl_image,
	struct blk_desc *block_dev, int partition,
	const char *filename);
	int spl_load_image_fat_os(struct spl_image_info *spl_image,
	struct blk_desc *block_dev, int partition);

	void __noreturn jump_to_image_no_args(struct spl_image_info *spl_image);

	/* SPL EXT image functions */
	int spl_load_image_ext(struct spl_image_info *spl_image,
	struct blk_desc *block_dev, int partition,
	const char *filename);
	int spl_load_image_ext_os(struct spl_image_info *spl_image,
	struct blk_desc *block_dev, int partition);

	/**
	* spl_early_init() - Set up device tree and driver model in SPL if enabled
	*
	* Call this function in board_init_f() if you want to use device tree and
	* driver model early, before board_init_r() is called.
	*
	* If this is not called, then driver model will be inactive in SPL's
	* board_init_f(), and no device tree will be available.
	*/
	int spl_early_init(void);

	/**
	* spl_init() - Set up device tree and driver model in SPL if enabled
	*
	* You can optionally call spl_early_init(), then optionally call spl_init().
	* This function will be called from board_init_r() if not called earlier.
	*
	* Both spl_early_init() and spl_init() perform a similar function except that
	* the latter will not set up the malloc() area if
	* CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN is enabled, since it is assumed to
	* already be done by a calll to spl_relocate_stack_gd() before board_init_r()
	* is reached.
	*
	* This function will be called from board_init_r() if not called earlier.
	*
	* If this is not called, then driver model will be inactive in SPL's
	* board_init_f(), and no device tree will be available.
	*/
	int spl_init(void);

	#ifdef CONFIG_SPL_BOARD_INIT
	void spl_board_init(void);
	#endif

	/**
	* spl_was_boot_source() - check if U-Boot booted from SPL
	*
	* This will normally be true, but if U-Boot jumps to second U-Boot, it will
	* be false. This should be implemented by board-specific code.
	*
	* @return true if U-Boot booted from SPL, else false
	*/
	bool spl_was_boot_source(void);

	/**
	* spl_dfu_cmd- run dfu command with chosen mmc device interface
	* @param usb_index - usb controller number
	* @param mmc_dev - mmc device nubmer
	*
	* @return 0 on success, otherwise error code
	*/
	int spl_dfu_cmd(int usbctrl, char dfu_alt_info, char interface, char *devstr);

	int spl_mmc_load_image(struct spl_image_info *spl_image,
	struct spl_boot_device *bootdev);

	#endif