| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright (C) 2012 Freescale Semiconductor, Inc. |
| * |
| * Configuration settings for the Freescale i.MX6Q SabreAuto board. |
| */ |
| |
| #ifndef __MX6SABREAUTO_CONFIG_H |
| #define __MX6SABREAUTO_CONFIG_H |
| |
| #ifdef CONFIG_SPL |
| #include "imx6_spl.h" |
| #endif |
| |
| #define CONFIG_MACH_TYPE 3529 |
| #define CONFIG_MXC_UART_BASE UART4_BASE |
| #define CONSOLE_DEV "ttymxc3" |
| |
| /* USB Configs */ |
| #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */ |
| #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) |
| #define CONFIG_MXC_USB_FLAGS 0 |
| |
| #define CONFIG_PCA953X |
| #define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x30, 8}, {0x32, 8}, {0x34, 8} } |
| |
| #include "mx6sabre_common.h" |
| |
| /* Falcon Mode */ |
| #ifdef CONFIG_SPL_OS_BOOT |
| #define CONFIG_SPL_FS_LOAD_ARGS_NAME "args" |
| #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" |
| #define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000 |
| |
| /* Falcon Mode - MMC support: args@1MB kernel@2MB */ |
| #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x800 /* 1MB */ |
| #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512) |
| #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000 /* 2MB */ |
| #endif |
| |
| #ifdef CONFIG_MTD_NOR_FLASH |
| #define CONFIG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR |
| #define CONFIG_SYS_FLASH_SECT_SIZE (128 * 1024) |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT |
| #endif |
| |
| #define CONFIG_SYS_FSL_USDHC_NUM 2 |
| |
| /* NAND stuff */ |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE 0x40000000 |
| #define CONFIG_SYS_NAND_5_ADDR_CYCLE |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| |
| /* DMA stuff, needed for GPMI/MXS NAND support */ |
| |
| /* PMIC */ |
| #define CONFIG_POWER |
| #define CONFIG_POWER_I2C |
| #define CONFIG_POWER_PFUZE100 |
| #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 |
| |
| #endif /* __MX6SABREAUTO_CONFIG_H */ |