include/configs/m28evk.h - platform/external/u-boot - Gitiles

 /*
  * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
  * on behalf of DENX Software Engineering GmbH
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
 #ifndef __CONFIGS_M28EVK_H__
 #define __CONFIGS_M28EVK_H__

 /* System configurations */
 #define CONFIG_MX28				/* i.MX28 SoC */
 #define CONFIG_MACH_TYPE	MACH_TYPE_M28EVK

 #define CONFIG_TIMESTAMP		/* Print image info with timestamp */

 /* U-Boot Commands */
 #define CONFIG_FAT_WRITE

 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_NAND_TRIMFFS

 /* Memory configuration */
 #define CONFIG_NR_DRAM_BANKS		1		/* 1 bank of DRAM */
 #define PHYS_SDRAM_1			0x40000000	/* Base address */
 #define PHYS_SDRAM_1_SIZE		0x20000000	/* Max 512 MB RAM */
 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1

 /* Environment */
 #define CONFIG_ENV_SIZE			(16 * 1024)
 #define CONFIG_ENV_IS_IN_NAND

 /* Environment is in NAND */
 #if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND)
 #define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
 #define CONFIG_ENV_SECT_SIZE		(128 * 1024)
 #define CONFIG_ENV_RANGE		(4 * CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_OFFSET		(24 * CONFIG_ENV_SECT_SIZE) /* 3 MiB */
 #define CONFIG_ENV_OFFSET_REDUND	\
 		(CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)

 #define CONFIG_CMD_UBIFS
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_RBTREE
 #define CONFIG_LZO
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS
 #define MTDIDS_DEFAULT			"nand0=gpmi-nand"
 #define MTDPARTS_DEFAULT			\
 	"mtdparts=gpmi-nand:"			\
 		"3m(u-boot),"			\
 		"512k(env1),"			\
 		"512k(env2),"			\
 		"14m(boot),"			\
 		"238m(data),"			\
 		"-@4096k(UBI)"
 #else
 #define CONFIG_ENV_IS_NOWHERE
 #endif

 /* FEC Ethernet on SoC */
 #ifdef CONFIG_CMD_NET
 #define CONFIG_FEC_MXC
 #endif

 /* RTC */
 #ifdef CONFIG_CMD_DATE
 /* Use the internal RTC in the MXS chip */
 #define CONFIG_RTC_INTERNAL
 #ifdef CONFIG_RTC_INTERNAL
 #define CONFIG_RTC_MXS
 #else
 #define CONFIG_RTC_M41T62
 #define CONFIG_SYS_I2C_RTC_ADDR		0x68
 #define CONFIG_SYS_M41T11_BASE_YEAR	2000
 #endif
 #endif

 /* USB */
 #ifdef CONFIG_CMD_USB
 #define CONFIG_EHCI_MXS_PORT0
 #define CONFIG_EHCI_MXS_PORT1
 #define CONFIG_USB_MAX_CONTROLLER_COUNT	2
 #endif

 /* SPI */
 #ifdef CONFIG_CMD_SPI
 #define CONFIG_DEFAULT_SPI_BUS		2
 #define CONFIG_DEFAULT_SPI_CS		0
 #define CONFIG_DEFAULT_SPI_MODE		SPI_MODE_0

 /* SPI FLASH */
 #ifdef CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_BUS		2
 #define CONFIG_SF_DEFAULT_CS		0
 #define CONFIG_SF_DEFAULT_SPEED		40000000
 #define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0

 #define CONFIG_ENV_SPI_BUS		2
 #define CONFIG_ENV_SPI_CS		0
 #define CONFIG_ENV_SPI_MAX_HZ		40000000
 #define CONFIG_ENV_SPI_MODE		SPI_MODE_0
 #endif

 #endif

 /* LCD */
 #ifdef CONFIG_VIDEO
 #define	CONFIG_VIDEO_LOGO
 #define	CONFIG_SPLASH_SCREEN
 #define	CONFIG_BMP_16BPP
 #define	CONFIG_VIDEO_BMP_RLE8
 #define	CONFIG_VIDEO_BMP_GZIP
 #define	CONFIG_SYS_VIDEO_LOGO_MAX_SIZE	(2 << 20)
 #endif

 /* Booting Linux */
 #define CONFIG_BOOTFILE		"fitImage"
 #define CONFIG_BOOTARGS		"console=ttyAMA0,115200n8 "
 #define CONFIG_BOOTCOMMAND	"run mmc_mmc"
 #define CONFIG_LOADADDR		0x42000000
 #define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR

 /* Extra Environment */
 #define CONFIG_PREBOOT		"run try_bootscript"
 #define CONFIG_HOSTNAME		m28evk

 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"consdev=ttyAMA0\0"						\
 	"baudrate=115200\0"						\
 	"bootscript=boot.scr\0"						\
 	"bootdev=/dev/mmcblk0p2\0"					\
 	"rootdev=/dev/mmcblk0p3\0"					\
 	"netdev=eth0\0"							\
 	"hostname=m28evk\0"						\
 	"rootpath=/opt/eldk-5.5/armv5te/rootfs-qte-sdk\0"		\
 	"kernel_addr_r=0x42000000\0"					\
 	"videomode=video=ctfb:x:800,y:480,depth:18,mode:0,pclk:30066,"	\
 		"le:0,ri:256,up:0,lo:45,hs:1,vs:1,sync:100663296,"	\
 		"vmode:0\0"						\
 	"update_nand_full_filename=u-boot.nand\0"			\
 	"update_nand_firmware_filename=u-boot.sb\0"			\
 	"update_sd_firmware_filename=u-boot.sd\0"			\
 	"update_nand_firmware_maxsz=0x100000\0"				\
 	"update_nand_stride=0x40\0"	/* MX28 datasheet ch. 12.12 */	\
 	"update_nand_count=0x4\0"	/* MX28 datasheet ch. 12.12 */	\
 	"update_nand_get_fcb_size="	/* Get size of FCB blocks */	\
 		"nand device 0 ; "					\
 		"nand info ; "						\
 		"setexpr fcb_sz ${update_nand_stride} * ${update_nand_count};" \
 		"setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \
 	"update_nand_full="		/* Update FCB, DBBT and FW */	\
 		"if tftp ${update_nand_full_filename} ; then "		\
 		"run update_nand_get_fcb_size ; "			\
 		"nand scrub -y 0x0 ${filesize} ; "			\
 		"nand write.raw ${loadaddr} 0x0 ${fcb_sz} ; "		\
 		"setexpr update_off ${loadaddr} + ${update_nand_fcb} ; " \
 		"setexpr update_sz ${filesize} - ${update_nand_fcb} ; " \
 		"nand write ${update_off} ${update_nand_fcb} ${update_sz} ; " \
 		"fi\0"							\
 	"update_nand_firmware="		/* Update only firmware */	\
 		"if tftp ${update_nand_firmware_filename} ; then "	\
 		"run update_nand_get_fcb_size ; "			\
 		"setexpr fcb_sz ${update_nand_fcb} * 2 ; " /* FCB + DBBT */ \
 		"setexpr fw_sz ${update_nand_firmware_maxsz} * 2 ; "	\
 		"setexpr fw_off ${fcb_sz} + ${update_nand_firmware_maxsz};" \
 		"nand erase ${fcb_sz} ${fw_sz} ; "			\
 		"nand write ${loadaddr} ${fcb_sz} ${filesize} ; "	\
 		"nand write ${loadaddr} ${fw_off} ${filesize} ; "	\
 		"fi\0"							\
 	"update_sd_firmware="		/* Update the SD firmware partition */ \
 		"if mmc rescan ; then "					\
 		"if tftp ${update_sd_firmware_filename} ; then "	\
 		"setexpr fw_sz ${filesize} / 0x200 ; "	/* SD block size */ \
 		"setexpr fw_sz ${fw_sz} + 1 ; "				\
 		"mmc write ${loadaddr} 0x800 ${fw_sz} ; "		\
 		"fi ; "							\
 		"fi\0"							\
 	"addcons="							\
 		"setenv bootargs ${bootargs} "				\
 		"console=${consdev},${baudrate}\0"			\
 	"addip="							\
 		"setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:"		\
 			"${netmask}:${hostname}:${netdev}:off\0"	\
 	"addmisc="							\
 		"setenv bootargs ${bootargs} ${miscargs}\0"		\
 	"adddfltmtd="							\
 		"if test \"x${mtdparts}\" == \"x\" ; then "		\
 			"mtdparts default ; "				\
 		"fi\0"							\
 	"addmtd="							\
 		"run adddfltmtd ; "					\
 		"setenv bootargs ${bootargs} ${mtdparts}\0"		\
 	"addargs=run addcons addmtd addmisc\0"				\
 	"mmcload="							\
 		"mmc rescan ; "						\
 		"load mmc 0:2 ${kernel_addr_r} ${bootfile}\0"		\
 	"ubiload="							\
 		"ubi part UBI ; ubifsmount ubi0:rootfs ; "		\
 		"ubifsload ${kernel_addr_r} /boot/${bootfile}\0"	\
 	"netload="							\
 		"tftp ${kernel_addr_r} ${hostname}/${bootfile}\0"	\
 	"miscargs=nohlt panic=1\0"					\
 	"mmcargs=setenv bootargs root=${rootdev} rw rootwait\0"		\
 	"ubiargs="							\
 		"setenv bootargs ubi.mtd=5 "				\
 		"root=ubi0:rootfs rootfstype=ubifs\0"			\
 	"nfsargs="							\
 		"setenv bootargs root=/dev/nfs rw "			\
 			"nfsroot=${serverip}:${rootpath},v3,tcp\0"	\
 	"mmc_mmc="							\
 		"run mmcload mmcargs addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"mmc_ubi="							\
 		"run mmcload ubiargs addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"mmc_nfs="							\
 		"run mmcload nfsargs addip addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"ubi_mmc="							\
 		"run ubiload mmcargs addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"ubi_ubi="							\
 		"run ubiload ubiargs addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"ubi_nfs="							\
 		"run ubiload nfsargs addip addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"net_mmc="							\
 		"run netload mmcargs addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"net_ubi="							\
 		"run netload ubiargs addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"net_nfs="							\
 		"run netload nfsargs addip addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"try_bootscript="						\
 		"mmc rescan;"						\
 		"if test -e mmc 0:2 ${bootscript} ; then "		\
 		"if load mmc 0:2 ${kernel_addr_r} ${bootscript};"	\
 		"then ; "						\
 			"echo Running bootscript... ; "			\
 			"source ${kernel_addr_r} ; "			\
 		"fi ; "							\
 		"fi\0"

 /* The rest of the configuration is shared */
 #include <configs/mxs.h>

 #endif /* __CONFIGS_M28EVK_H__ */
	/*
	* Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
	* on behalf of DENX Software Engineering GmbH
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/
	#ifndef __CONFIGS_M28EVK_H__
	#define __CONFIGS_M28EVK_H__

	/* System configurations */
	#define CONFIG_MX28 /* i.MX28 SoC */
	#define CONFIG_MACH_TYPE MACH_TYPE_M28EVK

	#define CONFIG_TIMESTAMP /* Print image info with timestamp */

	/* U-Boot Commands */
	#define CONFIG_FAT_WRITE

	#define CONFIG_CMD_NAND
	#define CONFIG_CMD_NAND_TRIMFFS

	/* Memory configuration */
	#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
	#define PHYS_SDRAM_1 0x40000000 /* Base address */
	#define PHYS_SDRAM_1_SIZE 0x20000000 /* Max 512 MB RAM */
	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1

	/* Environment */
	#define CONFIG_ENV_SIZE (16 * 1024)
	#define CONFIG_ENV_IS_IN_NAND

	/* Environment is in NAND */
	#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND)
	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	#define CONFIG_ENV_SECT_SIZE (128 * 1024)
	#define CONFIG_ENV_RANGE (4 * CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_OFFSET (24 * CONFIG_ENV_SECT_SIZE) /* 3 MiB */
	#define CONFIG_ENV_OFFSET_REDUND \
	(CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)

	#define CONFIG_CMD_UBIFS
	#define CONFIG_CMD_MTDPARTS
	#define CONFIG_RBTREE
	#define CONFIG_LZO
	#define CONFIG_MTD_DEVICE
	#define CONFIG_MTD_PARTITIONS
	#define MTDIDS_DEFAULT "nand0=gpmi-nand"
	#define MTDPARTS_DEFAULT \
	"mtdparts=gpmi-nand:" \
	"3m(u-boot)," \
	"512k(env1)," \
	"512k(env2)," \
	"14m(boot)," \
	"238m(data)," \
	"-@4096k(UBI)"
	#else
	#define CONFIG_ENV_IS_NOWHERE
	#endif

	/* FEC Ethernet on SoC */
	#ifdef CONFIG_CMD_NET
	#define CONFIG_FEC_MXC
	#endif

	/* RTC */
	#ifdef CONFIG_CMD_DATE
	/* Use the internal RTC in the MXS chip */
	#define CONFIG_RTC_INTERNAL
	#ifdef CONFIG_RTC_INTERNAL
	#define CONFIG_RTC_MXS
	#else
	#define CONFIG_RTC_M41T62
	#define CONFIG_SYS_I2C_RTC_ADDR 0x68
	#define CONFIG_SYS_M41T11_BASE_YEAR 2000
	#endif
	#endif

	/* USB */
	#ifdef CONFIG_CMD_USB
	#define CONFIG_EHCI_MXS_PORT0
	#define CONFIG_EHCI_MXS_PORT1
	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
	#endif

	/* SPI */
	#ifdef CONFIG_CMD_SPI
	#define CONFIG_DEFAULT_SPI_BUS 2
	#define CONFIG_DEFAULT_SPI_CS 0
	#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0

	/* SPI FLASH */
	#ifdef CONFIG_CMD_SF
	#define CONFIG_SF_DEFAULT_BUS 2
	#define CONFIG_SF_DEFAULT_CS 0
	#define CONFIG_SF_DEFAULT_SPEED 40000000
	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0

	#define CONFIG_ENV_SPI_BUS 2
	#define CONFIG_ENV_SPI_CS 0
	#define CONFIG_ENV_SPI_MAX_HZ 40000000
	#define CONFIG_ENV_SPI_MODE SPI_MODE_0
	#endif

	#endif

	/* LCD */
	#ifdef CONFIG_VIDEO
	#define CONFIG_VIDEO_LOGO
	#define CONFIG_SPLASH_SCREEN
	#define CONFIG_BMP_16BPP
	#define CONFIG_VIDEO_BMP_RLE8
	#define CONFIG_VIDEO_BMP_GZIP
	#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)
	#endif

	/* Booting Linux */
	#define CONFIG_BOOTFILE "fitImage"
	#define CONFIG_BOOTARGS "console=ttyAMA0,115200n8 "
	#define CONFIG_BOOTCOMMAND "run mmc_mmc"
	#define CONFIG_LOADADDR 0x42000000
	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR

	/* Extra Environment */
	#define CONFIG_PREBOOT "run try_bootscript"
	#define CONFIG_HOSTNAME m28evk

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"consdev=ttyAMA0\0" \
	"baudrate=115200\0" \
	"bootscript=boot.scr\0" \
	"bootdev=/dev/mmcblk0p2\0" \
	"rootdev=/dev/mmcblk0p3\0" \
	"netdev=eth0\0" \
	"hostname=m28evk\0" \
	"rootpath=/opt/eldk-5.5/armv5te/rootfs-qte-sdk\0" \
	"kernel_addr_r=0x42000000\0" \
	"videomode=video=ctfb:x:800,y:480,depth:18,mode:0,pclk:30066," \
	"le:0,ri:256,up:0,lo:45,hs:1,vs:1,sync:100663296," \
	"vmode:0\0" \
	"update_nand_full_filename=u-boot.nand\0" \
	"update_nand_firmware_filename=u-boot.sb\0" \
	"update_sd_firmware_filename=u-boot.sd\0" \
	"update_nand_firmware_maxsz=0x100000\0" \
	"update_nand_stride=0x40\0" /* MX28 datasheet ch. 12.12 */ \
	"update_nand_count=0x4\0" /* MX28 datasheet ch. 12.12 */ \
	"update_nand_get_fcb_size=" /* Get size of FCB blocks */ \
	"nand device 0 ; " \
	"nand info ; " \
	"setexpr fcb_sz ${update_nand_stride} * ${update_nand_count};" \
	"setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \
	"update_nand_full=" /* Update FCB, DBBT and FW */ \
	"if tftp ${update_nand_full_filename} ; then " \
	"run update_nand_get_fcb_size ; " \
	"nand scrub -y 0x0 ${filesize} ; " \
	"nand write.raw ${loadaddr} 0x0 ${fcb_sz} ; " \
	"setexpr update_off ${loadaddr} + ${update_nand_fcb} ; " \
	"setexpr update_sz ${filesize} - ${update_nand_fcb} ; " \
	"nand write ${update_off} ${update_nand_fcb} ${update_sz} ; " \
	"fi\0" \
	"update_nand_firmware=" /* Update only firmware */ \
	"if tftp ${update_nand_firmware_filename} ; then " \
	"run update_nand_get_fcb_size ; " \
	"setexpr fcb_sz ${update_nand_fcb} * 2 ; " /* FCB + DBBT */ \
	"setexpr fw_sz ${update_nand_firmware_maxsz} * 2 ; " \
	"setexpr fw_off ${fcb_sz} + ${update_nand_firmware_maxsz};" \
	"nand erase ${fcb_sz} ${fw_sz} ; " \
	"nand write ${loadaddr} ${fcb_sz} ${filesize} ; " \
	"nand write ${loadaddr} ${fw_off} ${filesize} ; " \
	"fi\0" \
	"update_sd_firmware=" /* Update the SD firmware partition */ \
	"if mmc rescan ; then " \
	"if tftp ${update_sd_firmware_filename} ; then " \
	"setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \
	"setexpr fw_sz ${fw_sz} + 1 ; " \
	"mmc write ${loadaddr} 0x800 ${fw_sz} ; " \
	"fi ; " \
	"fi\0" \
	"addcons=" \
	"setenv bootargs ${bootargs} " \
	"console=${consdev},${baudrate}\0" \
	"addip=" \
	"setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:" \
	"${netmask}:${hostname}:${netdev}:off\0" \
	"addmisc=" \
	"setenv bootargs ${bootargs} ${miscargs}\0" \
	"adddfltmtd=" \
	"if test \"x${mtdparts}\" == \"x\" ; then " \
	"mtdparts default ; " \
	"fi\0" \
	"addmtd=" \
	"run adddfltmtd ; " \
	"setenv bootargs ${bootargs} ${mtdparts}\0" \
	"addargs=run addcons addmtd addmisc\0" \
	"mmcload=" \
	"mmc rescan ; " \
	"load mmc 0:2 ${kernel_addr_r} ${bootfile}\0" \
	"ubiload=" \
	"ubi part UBI ; ubifsmount ubi0:rootfs ; " \
	"ubifsload ${kernel_addr_r} /boot/${bootfile}\0" \
	"netload=" \
	"tftp ${kernel_addr_r} ${hostname}/${bootfile}\0" \
	"miscargs=nohlt panic=1\0" \
	"mmcargs=setenv bootargs root=${rootdev} rw rootwait\0" \
	"ubiargs=" \
	"setenv bootargs ubi.mtd=5 " \
	"root=ubi0:rootfs rootfstype=ubifs\0" \
	"nfsargs=" \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath},v3,tcp\0" \
	"mmc_mmc=" \
	"run mmcload mmcargs addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"mmc_ubi=" \
	"run mmcload ubiargs addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"mmc_nfs=" \
	"run mmcload nfsargs addip addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"ubi_mmc=" \
	"run ubiload mmcargs addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"ubi_ubi=" \
	"run ubiload ubiargs addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"ubi_nfs=" \
	"run ubiload nfsargs addip addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"net_mmc=" \
	"run netload mmcargs addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"net_ubi=" \
	"run netload ubiargs addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"net_nfs=" \
	"run netload nfsargs addip addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"try_bootscript=" \
	"mmc rescan;" \
	"if test -e mmc 0:2 ${bootscript} ; then " \
	"if load mmc 0:2 ${kernel_addr_r} ${bootscript};" \
	"then ; " \
	"echo Running bootscript... ; " \
	"source ${kernel_addr_r} ; " \
	"fi ; " \
	"fi\0"

	/* The rest of the configuration is shared */
	#include <configs/mxs.h>

	#endif /* __CONFIGS_M28EVK_H__ */