| /* |
| * (C) Copyright 2000, 2001, 2002 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| /* Yoo. Jonghoon, IPone, yooth@ipone.co.kr |
| * U-Boot port on RPXlite board |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define RPXClassic_50MHz |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_MPC860 1 |
| #define CONFIG_RPXCLASSIC 1 |
| |
| #define CONFIG_SYS_TEXT_BASE 0xff000000 |
| |
| #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ |
| #undef CONFIG_8xx_CONS_SMC2 |
| #undef CONFIG_8xx_CONS_NONE |
| #define CONFIG_BAUDRATE 9600 /* console baudrate = 9600bps */ |
| |
| /* Define CONFIG_FEC_ENET to use Fast ethernet instead of ethernet on SCC1 */ |
| #define CONFIG_FEC_ENET |
| #ifdef CONFIG_FEC_ENET |
| #define CONFIG_SYS_DISCOVER_PHY 1 |
| #define CONFIG_MII 1 |
| #endif /* CONFIG_FEC_ENET */ |
| #define CONFIG_MISC_INIT_R |
| |
| /* Video console (graphic: Epson SED13806 on ECCX board, no keyboard */ |
| #if 1 |
| #define CONFIG_VIDEO_SED13806 |
| #define CONFIG_NEC_NL6448BC20 |
| #define CONFIG_VIDEO_SED13806_16BPP |
| |
| #define CONFIG_CFB_CONSOLE |
| #define CONFIG_VIDEO_LOGO |
| #define CONFIG_VIDEO_BMP_LOGO |
| #define CONFIG_CONSOLE_EXTRA_INFO |
| #define CONFIG_VGA_AS_SINGLE_DEVICE |
| #define CONFIG_VIDEO_SW_CURSOR |
| #endif |
| |
| #if 0 |
| #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ |
| #else |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| #endif |
| |
| #define CONFIG_ZERO_BOOTDELAY_CHECK 1 |
| |
| #undef CONFIG_BOOTARGS |
| #define CONFIG_BOOTCOMMAND \ |
| "tftpboot; " \ |
| "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ |
| "bootm" |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| |
| |
| #define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ELF |
| |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_RESET_ADDRESS 0x80000000 |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x0040000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ |
| |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| */ |
| /*----------------------------------------------------------------------- |
| * Internal Memory Mapped Register |
| */ |
| #define CONFIG_SYS_IMMR 0xFA200000 |
| |
| /*----------------------------------------------------------------------------- |
| * I2C Configuration |
| *----------------------------------------------------------------------------- |
| */ |
| #define CONFIG_I2C 1 |
| #define CONFIG_SYS_I2C_SPEED 50000 |
| #define CONFIG_SYS_I2C_SLAVE 0x34 |
| |
| |
| /* enable I2C and select the hardware/software driver */ |
| #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| /* |
| * Software (bit-bang) I2C driver configuration |
| */ |
| #define I2C_PORT 1 /* Port A=0, B=1, C=2, D=3 */ |
| #define I2C_ACTIVE (iop->pdir |= 0x00000010) |
| #define I2C_TRISTATE (iop->pdir &= ~0x00000010) |
| #define I2C_READ ((iop->pdat & 0x00000010) != 0) |
| #define I2C_SDA(bit) if(bit) iop->pdat |= 0x00000010; \ |
| else iop->pdat &= ~0x00000010 |
| #define I2C_SCL(bit) if(bit) iop->pdat |= 0x00000020; \ |
| else iop->pdat &= ~0x00000020 |
| #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ |
| |
| |
| # define CONFIG_SYS_I2C_SPEED 50000 |
| # define CONFIG_SYS_I2C_SLAVE 0x34 |
| # define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */ |
| # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ |
| /* mask of address bits that overflow into the "EEPROM chip address" */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in DPRAM) |
| */ |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x3000 /* Size of used area in DPRAM */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_FLASH_BASE 0xFF000000 |
| |
| #if defined(DEBUG) || defined (CONFIG_VIDEO_SED13806) || defined(CONFIG_CMD_IDE) |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #else |
| #define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ |
| #endif |
| #define CONFIG_SYS_MONITOR_BASE 0xFF000000 |
| /*%%% #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE */ |
| #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #if 0 |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_OFFSET 0x20000 /* Offset of Environment Sector */ |
| #define CONFIG_ENV_SECT_SIZE 0x8000 |
| #define CONFIG_ENV_SIZE 0x8000 /* Total Size of Environment Sector */ |
| #else |
| #define CONFIG_ENV_IS_IN_NVRAM 1 |
| #define CONFIG_ENV_ADDR 0xfa000100 |
| #define CONFIG_ENV_SIZE 0x1000 |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SYPCR - System Protection Control 11-9 |
| * SYPCR can only be written once after reset! |
| *----------------------------------------------------------------------- |
| * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze |
| */ |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
| SYPCR_SWP) |
| |
| /*----------------------------------------------------------------------- |
| * SIUMCR - SIU Module Configuration 11-6 |
| *----------------------------------------------------------------------- |
| * PCMCIA config., multi-function pin tri-state |
| */ |
| #define CONFIG_SYS_SIUMCR (SIUMCR_MLRC10) |
| |
| /*----------------------------------------------------------------------- |
| * TBSCR - Time Base Status and Control 11-26 |
| *----------------------------------------------------------------------- |
| * Clear Reference Interrupt Status, Timebase freezing enabled |
| */ |
| #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE) |
| |
| /*----------------------------------------------------------------------- |
| * RTCSC - Real-Time Clock Status and Control Register 11-27 |
| *----------------------------------------------------------------------- |
| */ |
| /*%%%#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */ |
| #define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTE) |
| |
| /*----------------------------------------------------------------------- |
| * PISCR - Periodic Interrupt Status and Control 11-31 |
| *----------------------------------------------------------------------- |
| * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled |
| */ |
| #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) |
| |
| /*----------------------------------------------------------------------- |
| * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 |
| *----------------------------------------------------------------------- |
| * Reset PLL lock status sticky bit, timer expired status bit and timer |
| * interrupt status bit |
| * |
| * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)! |
| */ |
| /* up to 50 MHz we use a 1:1 clock */ |
| #define CONFIG_SYS_PLPRCR ( (4 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS | PLPRCR_SPLSS | PLPRCR_TMIST) |
| |
| /*----------------------------------------------------------------------- |
| * SCCR - System Clock and reset Control Register 15-27 |
| *----------------------------------------------------------------------- |
| * Set clock output, timebase and RTC source and divider, |
| * power management and some other internal clocks |
| */ |
| #define SCCR_MASK SCCR_EBDF00 |
| /* up to 50 MHz we use a 1:1 clock */ |
| #define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_TBS) |
| |
| /*----------------------------------------------------------------------- |
| * PCMCIA stuff |
| *----------------------------------------------------------------------- |
| * |
| */ |
| #define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) |
| #define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) |
| #define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) |
| #define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) |
| #define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) |
| |
| /*----------------------------------------------------------------------- |
| * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) |
| *----------------------------------------------------------------------- |
| */ |
| |
| #define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */ |
| #define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ |
| |
| #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ |
| #undef CONFIG_IDE_LED /* LED for ide not supported */ |
| #undef CONFIG_IDE_RESET /* reset for ide not supported */ |
| |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ |
| #define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ |
| |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| |
| #define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR |
| |
| /* Offset for data I/O */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) |
| |
| /* Offset for normal register accesses */ |
| #define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) |
| |
| /* Offset for alternate registers */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 |
| |
| /*----------------------------------------------------------------------- |
| * |
| *----------------------------------------------------------------------- |
| * |
| */ |
| /* #define CONFIG_SYS_DER 0x2002000F */ |
| #define CONFIG_SYS_DER 0 |
| |
| /* |
| * Init Memory Controller: |
| * |
| * BR0 and OR0 (FLASH) |
| */ |
| |
| #define FLASH_BASE_PRELIM 0xFE000000 /* FLASH base */ |
| #define CONFIG_SYS_PRELIM_OR_AM 0xFE000000 /* OR addr mask */ |
| |
| /* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */ |
| #define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI) |
| |
| #define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) |
| #define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V) |
| |
| /* |
| * BR1 and OR1 (SDRAM) |
| * |
| */ |
| #define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */ |
| #define SDRAM_MAX_SIZE 0x01000000 /* max 16 MB */ |
| |
| /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ |
| #define CONFIG_SYS_OR_TIMING_SDRAM 0x00000E00 |
| |
| #define CONFIG_SYS_OR1_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM ) |
| #define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) |
| |
| /* RPXLITE mem setting */ |
| #define CONFIG_SYS_BR3_PRELIM 0xFA400001 /* BCSR */ |
| #define CONFIG_SYS_OR3_PRELIM 0xff7f8970 |
| #define CONFIG_SYS_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */ |
| #define CONFIG_SYS_OR4_PRELIM 0xFFF80970 |
| |
| /* ECCX CS settings */ |
| #define SED13806_OR 0xFFC00108 /* - 4 Mo |
| - Burst inhibit |
| - external TA */ |
| #define SED13806_REG_ADDR 0xa0000000 |
| #define SED13806_ACCES 0x801 /* 16 bit access */ |
| |
| |
| /* Global definitions for the ECCX board */ |
| #define ECCX_CSR_ADDR (0xfac00000) |
| #define ECCX_CSR8_OFFSET (0x8) |
| #define ECCX_CSR11_OFFSET (0xB) |
| #define ECCX_CSR12_OFFSET (0xC) |
| |
| #define ECCX_CSR8 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR8_OFFSET) |
| #define ECCX_CSR11 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR11_OFFSET) |
| #define ECCX_CSR12 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR12_OFFSET) |
| |
| |
| #define REG_GPIO_CTRL 0x008 |
| |
| /* Definitions for CSR8 */ |
| #define ECCX_ENEPSON 0x80 /* Bit 0: |
| 0= disable and reset SED1386 |
| 1= enable SED1386 */ |
| /* Bit 1: 0= SED1386 in Big Endian mode */ |
| /* 1= SED1386 in little endian mode */ |
| #define ECCX_LE 0x40 |
| #define ECCX_BE 0x00 |
| |
| /* Bit 2,3: Selection */ |
| /* 00 = Disabled */ |
| /* 01 = CS2 is used for the SED1386 */ |
| /* 10 = CS5 is used for the SED1386 */ |
| /* 11 = reserved */ |
| #define ECCX_CS2 0x10 |
| #define ECCX_CS5 0x20 |
| |
| /* Definitions for CSR12 */ |
| #define ECCX_ID 0x02 |
| #define ECCX_860 0x01 |
| |
| /* |
| * Memory Periodic Timer Prescaler |
| */ |
| |
| /* periodic timer for refresh */ |
| #define CONFIG_SYS_MAMR_PTA 58 |
| |
| /* |
| * Refresh clock Prescalar |
| */ |
| #define CONFIG_SYS_MPTPR MPTPR_PTP_DIV8 |
| |
| /* |
| * MAMR settings for SDRAM |
| */ |
| |
| /* 10 column SDRAM */ |
| #define CONFIG_SYS_MAMR_10COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ |
| MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 | \ |
| MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X) |
| |
| /*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ |
| /* Configuration variable added by yooth. */ |
| /*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ |
| |
| /* |
| * BCSRx |
| * |
| * Board Status and Control Registers |
| * |
| */ |
| |
| #define BCSR0 0xFA400000 |
| #define BCSR1 0xFA400001 |
| #define BCSR2 0xFA400002 |
| #define BCSR3 0xFA400003 |
| |
| #define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */ |
| #define BCSR0_ENNVRAM 0x02 /* CS4# Control */ |
| #define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */ |
| #define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */ |
| #define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */ |
| #define BCSR0_COLTEST 0x20 |
| #define BCSR0_ETHLPBK 0x40 |
| #define BCSR0_ETHEN 0x80 |
| |
| #define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */ |
| #define BCSR1_PCVCTL6 0x02 |
| #define BCSR1_PCVCTL5 0x04 |
| #define BCSR1_PCVCTL4 0x08 |
| #define BCSR1_IPB5SEL 0x10 |
| |
| #define BCSR2_MIIRST 0x80 |
| #define BCSR2_MIIPWRDWN 0x40 |
| #define BCSR2_MIICTL 0x08 |
| |
| #define BCSR3_BWRTC 0x01 /* Real Time Clock Battery */ |
| #define BCSR3_BWNVR 0x02 /* NVRAM Battery */ |
| #define BCSR3_RDY_BSY 0x04 /* Flash Operation */ |
| #define BCSR3_RPXL 0x08 /* Reserved (reads back '1') */ |
| #define BCSR3_D27 0x10 /* Dip Switch settings */ |
| #define BCSR3_D26 0x20 |
| #define BCSR3_D25 0x40 |
| #define BCSR3_D24 0x80 |
| |
| |
| /* |
| * Environment setting |
| */ |
| |
| /* #define CONFIG_ETHADDR 00:10:EC:00:2C:A2 */ |
| /* #define CONFIG_IPADDR 10.10.106.1 */ |
| /* #define CONFIG_SERVERIP 10.10.104.11 */ |
| |
| #endif /* __CONFIG_H */ |