| /* |
| * Copyright 2004 Freescale Semiconductor. |
| * (C) Copyright 2002,2003 Motorola,Inc. |
| * Xianghua Xiao <X.Xiao@motorola.com> |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* |
| * mpc8540ads board configuration file |
| * |
| * Please refer to doc/README.mpc85xx for more info. |
| * |
| * Make sure you change the MAC address and other network params first, |
| * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_BOOKE 1 /* BOOKE */ |
| #define CONFIG_E500 1 /* BOOKE e500 family */ |
| #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ |
| #define CONFIG_MPC8540 1 /* MPC8540 specific */ |
| #define CONFIG_MPC8540ADS 1 /* MPC8540ADS board specific */ |
| |
| #ifndef CONFIG_HAS_FEC |
| #define CONFIG_HAS_FEC 1 /* 8540 has FEC */ |
| #endif |
| |
| #define CONFIG_PCI |
| #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ |
| #define CONFIG_TSEC_ENET /* tsec ethernet support */ |
| #define CONFIG_ENV_OVERWRITE |
| #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ |
| |
| /* |
| * sysclk for MPC85xx |
| * |
| * Two valid values are: |
| * 33000000 |
| * 66000000 |
| * |
| * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz |
| * is likely the desired value here, so that is now the default. |
| * The board, however, can run at 66MHz. In any event, this value |
| * must match the settings of some switches. Details can be found |
| * in the README.mpc85xxads. |
| * |
| * XXX -- Can't we run at 66 MHz, anyway? PCI should drop to |
| * 33MHz to accommodate, based on a PCI pin. |
| * Note that PCI-X won't work at 33MHz. |
| */ |
| |
| #ifndef CONFIG_SYS_CLK_FREQ |
| #define CONFIG_SYS_CLK_FREQ 33000000 |
| #endif |
| |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_L2_CACHE /* toggle L2 cache */ |
| #define CONFIG_BTB /* toggle branch predition */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ |
| #define CONFIG_SYS_MEMTEST_END 0x00400000 |
| |
| |
| /* |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| */ |
| #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ |
| #define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ |
| #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ |
| #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ |
| |
| /* DDR Setup */ |
| #define CONFIG_FSL_DDR1 |
| #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ |
| #define CONFIG_DDR_SPD |
| #undef CONFIG_FSL_DDR_INTERACTIVE |
| |
| #define CONFIG_MEM_INIT_VALUE 0xDeadBeef |
| |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| |
| #define CONFIG_NUM_DDR_CONTROLLERS 1 |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) |
| |
| /* I2C addresses of SPD EEPROMs */ |
| #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ |
| |
| /* These are used when DDR doesn't use SPD. */ |
| #define CONFIG_SYS_SDRAM_SIZE 128 /* DDR is 128MB */ |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ |
| #define CONFIG_SYS_DDR_CS0_CONFIG 0x80000002 |
| #define CONFIG_SYS_DDR_TIMING_1 0x37344321 |
| #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ |
| #define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ |
| #define CONFIG_SYS_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ |
| #define CONFIG_SYS_DDR_INTERVAL 0x05200100 /* autocharge,no open page */ |
| |
| /* |
| * SDRAM on the Local Bus |
| */ |
| #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ |
| #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ |
| |
| #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ |
| #define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */ |
| |
| #define CONFIG_SYS_OR0_PRELIM 0xff006ff7 /* 16MB Flash */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ |
| |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| #define CONFIG_SYS_RAMBOOT |
| #else |
| #undef CONFIG_SYS_RAMBOOT |
| #endif |
| |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| |
| #undef CONFIG_CLOCKS_IN_MHZ |
| |
| |
| /* |
| * Local Bus Definitions |
| */ |
| |
| /* |
| * Base Register 2 and Option Register 2 configure SDRAM. |
| * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. |
| * |
| * For BR2, need: |
| * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 |
| * port-size = 32-bits = BR2[19:20] = 11 |
| * no parity checking = BR2[21:22] = 00 |
| * SDRAM for MSEL = BR2[24:26] = 011 |
| * Valid = BR[31] = 1 |
| * |
| * 0 4 8 12 16 20 24 28 |
| * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 |
| * |
| * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into |
| * FIXME: the top 17 bits of BR2. |
| */ |
| |
| #define CONFIG_SYS_BR2_PRELIM 0xf0001861 |
| |
| /* |
| * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. |
| * |
| * For OR2, need: |
| * 64MB mask for AM, OR2[0:7] = 1111 1100 |
| * XAM, OR2[17:18] = 11 |
| * 9 columns OR2[19-21] = 010 |
| * 13 rows OR2[23-25] = 100 |
| * EAD set for extra time OR[31] = 1 |
| * |
| * 0 4 8 12 16 20 24 28 |
| * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 |
| */ |
| |
| #define CONFIG_SYS_OR2_PRELIM 0xfc006901 |
| |
| #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ |
| #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ |
| #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ |
| #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ |
| |
| /* |
| * LSDMR masks |
| */ |
| #define CONFIG_SYS_LBC_LSDMR_RFEN (1 << (31 - 1)) |
| #define CONFIG_SYS_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) |
| #define CONFIG_SYS_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) |
| #define CONFIG_SYS_LBC_LSDMR_RFCR5 (3 << (31 - 16)) |
| #define CONFIG_SYS_LBC_LSDMR_RFCR16 (7 << (31 - 16)) |
| #define CONFIG_SYS_LBC_LSDMR_PRETOACT3 (3 << (31 - 19)) |
| #define CONFIG_SYS_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) |
| #define CONFIG_SYS_LBC_LSDMR_ACTTORW3 (3 << (31 - 22)) |
| #define CONFIG_SYS_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) |
| #define CONFIG_SYS_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) |
| #define CONFIG_SYS_LBC_LSDMR_BL8 (1 << (31 - 23)) |
| #define CONFIG_SYS_LBC_LSDMR_WRC2 (2 << (31 - 27)) |
| #define CONFIG_SYS_LBC_LSDMR_WRC4 (0 << (31 - 27)) |
| #define CONFIG_SYS_LBC_LSDMR_BUFCMD (1 << (31 - 29)) |
| #define CONFIG_SYS_LBC_LSDMR_CL3 (3 << (31 - 31)) |
| |
| #define CONFIG_SYS_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_MRW (3 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) |
| |
| #define CONFIG_SYS_LBC_LSDMR_COMMON ( CONFIG_SYS_LBC_LSDMR_BSMA1516 \ |
| | CONFIG_SYS_LBC_LSDMR_RFCR5 \ |
| | CONFIG_SYS_LBC_LSDMR_PRETOACT3 \ |
| | CONFIG_SYS_LBC_LSDMR_ACTTORW3 \ |
| | CONFIG_SYS_LBC_LSDMR_BL8 \ |
| | CONFIG_SYS_LBC_LSDMR_WRC2 \ |
| | CONFIG_SYS_LBC_LSDMR_CL3 \ |
| | CONFIG_SYS_LBC_LSDMR_RFEN \ |
| ) |
| |
| /* |
| * SDRAM Controller configuration sequence. |
| */ |
| #define CONFIG_SYS_LBC_LSDMR_1 ( CONFIG_SYS_LBC_LSDMR_COMMON \ |
| | CONFIG_SYS_LBC_LSDMR_OP_PCHALL) |
| #define CONFIG_SYS_LBC_LSDMR_2 ( CONFIG_SYS_LBC_LSDMR_COMMON \ |
| | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH) |
| #define CONFIG_SYS_LBC_LSDMR_3 ( CONFIG_SYS_LBC_LSDMR_COMMON \ |
| | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH) |
| #define CONFIG_SYS_LBC_LSDMR_4 ( CONFIG_SYS_LBC_LSDMR_COMMON \ |
| | CONFIG_SYS_LBC_LSDMR_OP_MRW) |
| #define CONFIG_SYS_LBC_LSDMR_5 ( CONFIG_SYS_LBC_LSDMR_COMMON \ |
| | CONFIG_SYS_LBC_LSDMR_OP_NORMAL) |
| |
| |
| /* |
| * 32KB, 8-bit wide for ADS config reg |
| */ |
| #define CONFIG_SYS_BR4_PRELIM 0xf8000801 |
| #define CONFIG_SYS_OR4_PRELIM 0xffffe1f1 |
| #define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000) |
| |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ |
| #define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ |
| |
| /* Serial Port */ |
| #define CONFIG_CONS_INDEX 1 |
| #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) |
| |
| /* Use the HUSH parser */ |
| #define CONFIG_SYS_HUSH_PARSER |
| #ifdef CONFIG_SYS_HUSH_PARSER |
| #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " |
| #endif |
| |
| /* pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| #define CONFIG_OF_STDOUT_VIA_ALIAS 1 |
| |
| #define CONFIG_SYS_64BIT_VSPRINTF 1 |
| #define CONFIG_SYS_64BIT_STRTOUL 1 |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ |
| #define CONFIG_HARD_I2C /* I2C with hardware support*/ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CONFIG_SYS_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ |
| #define CONFIG_SYS_I2C_OFFSET 0x3000 |
| |
| /* RapidIO MMU */ |
| #define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */ |
| #define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE |
| #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */ |
| |
| /* |
| * General PCI |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 |
| #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE |
| #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 |
| #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 |
| #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ |
| |
| #if defined(CONFIG_PCI) |
| |
| #define CONFIG_NET_MULTI |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #undef CONFIG_EEPRO100 |
| #undef CONFIG_TULIP |
| |
| #if !defined(CONFIG_PCI_PNP) |
| #define PCI_ENET0_IOADDR 0xe0000000 |
| #define PCI_ENET0_MEMADDR 0xe0000000 |
| #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ |
| #endif |
| |
| #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ |
| |
| #endif /* CONFIG_PCI */ |
| |
| |
| #if defined(CONFIG_TSEC_ENET) |
| |
| #ifndef CONFIG_NET_MULTI |
| #define CONFIG_NET_MULTI 1 |
| #endif |
| |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_TSEC1 1 |
| #define CONFIG_TSEC1_NAME "TSEC0" |
| #define CONFIG_TSEC2 1 |
| #define CONFIG_TSEC2_NAME "TSEC1" |
| #define TSEC1_PHY_ADDR 0 |
| #define TSEC2_PHY_ADDR 1 |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| #define TSEC1_FLAGS TSEC_GIGABIT |
| #define TSEC2_FLAGS TSEC_GIGABIT |
| |
| |
| #if CONFIG_HAS_FEC |
| #define CONFIG_MPC85XX_FEC 1 |
| #define CONFIG_MPC85XX_FEC_NAME "FEC" |
| #define FEC_PHY_ADDR 3 |
| #define FEC_PHYIDX 0 |
| #define FEC_FLAGS 0 |
| #endif |
| |
| /* Options are: TSEC[0-1], FEC */ |
| #define CONFIG_ETHPRIME "TSEC0" |
| |
| #endif /* CONFIG_TSEC_ENET */ |
| |
| |
| /* |
| * Environment |
| */ |
| #ifndef CONFIG_SYS_RAMBOOT |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) |
| #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ |
| #define CONFIG_ENV_SIZE 0x2000 |
| #else |
| #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ |
| #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #endif |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_SETEXPR |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| #if defined(CONFIG_SYS_RAMBOOT) |
| #undef CONFIG_CMD_ENV |
| #undef CONFIG_CMD_LOADS |
| #endif |
| |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_CMDLINE_EDITING /* Command-line editing */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| |
| /* |
| * Environment Configuration |
| */ |
| |
| /* The mac addresses for all ethernet interface */ |
| #if defined(CONFIG_TSEC_ENET) |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_ETHADDR 00:E0:0C:00:00:FD |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD |
| #define CONFIG_HAS_ETH2 |
| #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD |
| #endif |
| |
| #define CONFIG_IPADDR 192.168.1.253 |
| |
| #define CONFIG_HOSTNAME unknown |
| #define CONFIG_ROOTPATH /nfsroot |
| #define CONFIG_BOOTFILE your.uImage |
| |
| #define CONFIG_SERVERIP 192.168.1.1 |
| #define CONFIG_GATEWAYIP 192.168.1.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| |
| #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ |
| |
| #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ |
| #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=1000000\0" \ |
| "ramdiskfile=your.ramdisk.u-boot\0" \ |
| "fdtaddr=400000\0" \ |
| "fdtfile=your.fdt.dtb\0" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND |
| |
| #endif /* __CONFIG_H */ |