ARM: dts: stm32mp1: DT alignment with Linux 5.7-rc2
DT alignment with Linux 5.7-rc2, including the kernel commits
431c89e6f323 ARM: dts: stm32: use correct vqmmc regu for eMMC on stm32mp1 ED1/EV1 boards
79e965053872 ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
877db62ea516 ARM: dts: stm32: add cd-gpios properties for SD-cards on STM32MP1 boards
7519e95ba5f8 ARM: dts: stm32: Do clean up in stmpic nodes on stm32mp15 boards
f68e2dbc591a ARM: dts: stm32: Rename stmfx joystick pins on stm32mp157c-ev1
d6210da4f8bf ARM: dts: stm32: add cpu clock-frequency property on stm32mp15x
b65b6fc56925 ARM: dts: stm32: add wakeup-source in all I2C nodes of stm32mp157c
1c1cf5996cfb ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp157c-ed1
bef15fc0fad9 ARM: dts: stm32: add i2c2/i2c5 sleep pinctrl on stm32mp157c-ev1
b7fc0a87b9ac ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp15xx-dkx
a5e557655285 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp15 DK boards
8bc631b650a6 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp157c-ed1
fccd6a577bb3 ARM: dts: stm32: Correct stmfx node name on stm32mp157c-ev1 board
cc775a83db65 ARM: dts: stm32: add resets property on all DMA nodes on stm32mp151
c5fae093511b ARM: dts: stm32: enable USB OTG Dual Role on stm32mp157c-ev1
9879e2165758 ARM: dts: stm32: add USB OTG pinctrl to stm32mp15
82ac8a81f985 ARM: dts: stm32: add USB OTG full support on stm32mp151
8714b26e2863 ARM: dts: stm32: remove useless properties in stm32mp157a-avenger96 stmpic node
a7959919709e ARM: dts: stm32: Add UART8 pins A pinmux entry on stm32mp1
4d7c53a684da ARM: dts: stm32: Add USART3 pins A pinmux entry on stm32mp1
80ab128332ee ARM: dts: stm32: Add SAI2A pins B pinmux entry on stm32mp1
ab7f98c0c546 ARM: dts: stm32: Add Ethernet0 RMII pins A pinmux entry on stm32mp1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
diff --git a/arch/arm/dts/stm32mp157c-ed1.dts b/arch/arm/dts/stm32mp157c-ed1.dts
index 05d5326..4fb7110 100644
--- a/arch/arm/dts/stm32mp157c-ed1.dts
+++ b/arch/arm/dts/stm32mp157c-ed1.dts
@@ -135,10 +135,12 @@
};
&i2c4 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c4_pins_a>;
+ pinctrl-1 = <&i2c4_pins_sleep_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
+ clock-frequency = <400000>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
@@ -223,8 +225,6 @@
vdd_usb: ldo4 {
regulator-name = "vdd_usb";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
interrupts = <IT_CURLIM_LDO4 0>;
};
@@ -246,7 +246,6 @@
vref_ddr: vref_ddr {
regulator-name = "vref_ddr";
regulator-always-on;
- regulator-over-current-protection;
};
bst_out: boost {
@@ -318,7 +317,8 @@
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
- broken-cd;
+ cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
st,sig-dir;
st,neg-edge;
st,use-ckin;
@@ -339,7 +339,7 @@
st,neg-edge;
bus-width = <8>;
vmmc-supply = <&v3v3>;
- vqmmc-supply = <&v3v3>;
+ vqmmc-supply = <&vdd>;
mmc-ddr-3_3v;
status = "okay";
};