include/configs/o2dnt-common.h - platform/external/u-boot - Gitiles

 /*
  *  Common configuration options for ifm camera boards
  *
  * (C) Copyright 2005
  * Sebastien Cazaux, ifm electronic gmbh
  *
  * (C) Copyright 2012
  * DENX Software Engineering, Anatolij Gustschin <agust@denx.de>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __O2D_CONFIG_H
 #define __O2D_CONFIG_H

 /*
  * High Level Configuration Options
  */
 #define CONFIG_MPC5200
 #define CONFIG_DISPLAY_BOARDINFO

 #define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* running at 33.000000MHz */

 #define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
 #if defined(CONFIG_CMD_KGDB)
 /* log base 2 of the above value */
 #define CONFIG_SYS_CACHELINE_SHIFT	5
 #endif

 /*
 #define CONFIG_POST	(CONFIG_SYS_POST_MEMORY | \
 			 CONFIG_SYS_POST_I2C)
 */

 #ifdef CONFIG_POST
 /* preserve space for the post_word at end of on-chip SRAM */
 #define MPC5XXX_SRAM_POST_SIZE	(MPC5XXX_SRAM_SIZE - 4)
 #endif

 /*
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE	5	/* console is on PSC5 */
 #define CONFIG_BAUDRATE		115200	/* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE \
 	{ 9600, 19200, 38400, 57600, 115200, 230400 }

 /*
  * PCI Mapping:
  * 0x40000000 - 0x4fffffff - PCI Memory
  * 0x50000000 - 0x50ffffff - PCI IO Space
  */
 #undef CONFIG_PCI
 #define CONFIG_PCI_PNP		1

 #define CONFIG_PCI_MEM_BUS	0x40000000
 #define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
 #define CONFIG_PCI_MEM_SIZE	0x10000000

 #define CONFIG_PCI_IO_BUS	0x50000000
 #define CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
 #define CONFIG_PCI_IO_SIZE	0x01000000

 #define CONFIG_SYS_XLB_PIPELINING	1

 /* Partitions */
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
 #define CONFIG_ISO_PARTITION

 #define CONFIG_TIMESTAMP	/* Print image info with timestamp */

 #define CONFIG_SYS_ALT_MEMTEST	/* Much more complex memory test */

 /*
  * Supported commands
  */
 #define CONFIG_CMD_EEPROM
 #ifdef CONFIG_PCI
 #define CONFIG_CMD_PCI
 #endif
 #ifdef CONFIG_POST
 #define CONFIG_CMD_DIAG
 #endif

 #if (CONFIG_SYS_TEXT_BASE == 0xFC000000) || (CONFIG_SYS_TEXT_BASE == 0xFF000000)
 /* Boot low with 16 or 32 MB Flash */
 #define CONFIG_SYS_LOWBOOT	1
 #elif (CONFIG_SYS_TEXT_BASE != 0x00100000)
 #error "CONFIG_SYS_TEXT_BASE value is invalid"
 #endif

 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */

 #define CONFIG_PREBOOT	"run master"

 #undef	CONFIG_BOOTARGS

 #if !defined(CONFIG_CONSOLE_DEV)
 #define CONFIG_CONSOLE_DEV	"ttyPSC1"
 #endif

 /*
  * Default environment for booting old and new kernel versions
  */
 #define CONFIG_IFM_DEFAULT_ENV_OLD					\
 	"flash_self_old=run ramargs addip addmem;"			\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"flash_nfs_old=run nfsargs addip addmem;"			\
 		"bootm ${kernel_addr}\0"				\
 	"net_nfs_old=tftp ${kernel_addr_r} ${bootfile};"		\
 		"run nfsargs addip addmem;"				\
 		"bootm ${kernel_addr_r}\0"

 #define CONFIG_IFM_DEFAULT_ENV_NEW					\
 	"fdt_addr_r=900000\0"						\
 	"fdt_file="CONFIG_BOARD_NAME"/"CONFIG_BOARD_NAME".dtb\0"	\
 	"flash_self=run ramargs addip addtty addmisc;"			\
 		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
 	"flash_nfs=run nfsargs addip addtty addmisc;"			\
 		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
 	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
 		"tftp ${fdt_addr_r} ${fdt_file}; "			\
 		"run nfsargs addip addtty addmisc;"			\
 		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\

 #define	CONFIG_IFM_DEFAULT_ENV_SETTINGS					\
 	"IOpin=0x64\0"							\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addmem=setenv bootargs ${bootargs} ${memlimit}\0"		\
 	"addmisc=sete bootargs ${bootargs} ${miscargs}\0"		\
 	"addtty=sete bootargs ${bootargs} console="			\
 		CONFIG_CONSOLE_DEV ",${baudrate}\0"			\
 	"bootfile="CONFIG_BOARD_NAME"/uImage_"CONFIG_BOARD_NAME"_act\0"	\
 	"kernel_addr_r=600000\0"					\
 	"initrd_high=0x03e00000\0"					\
 	"memlimit=mem="CONFIG_BOARD_MEM_LIMIT"M\0"			\
 	"memtest=mtest 0x00100000 "__stringify(CONFIG_SYS_MEMTEST_END)" 0 1\0" \
 	"netdev=eth0\0"							\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"linuxname="CONFIG_BOARD_NAME"/uImage_"CONFIG_BOARD_NAME"_act\0"\
 	"progLinux=tftp 200000 ${linuxname};erase ${linbot} ${lintop};" \
 		"cp.b ${fileaddr} ${linbot} ${filesize}\0"		\
 	"ramname="CONFIG_BOARD_NAME"/uRamdisk_"CONFIG_BOARD_NAME"_act\0"\
 	"progRam=tftp 200000 ${ramname};erase ${rambot} ${ramtop};"	\
 		"cp.b ${fileaddr} ${rambot} ${filesize}\0"		\
 	"jffname="CONFIG_BOARD_NAME"/uJFFS2_"CONFIG_BOARD_NAME"_act\0"	\
 	"progJff=tftp 200000 ${jffname};erase ${jffbot} ${jfftop};"	\
 		"cp.b ${fileaddr} ${jffbot} ${filesize}\0"		\
 	"rootpath=/opt/eldk/ppc_6xx\0"					\
 	"uboname=" CONFIG_BOARD_NAME					\
 		"/u-boot.bin_" CONFIG_BOARD_NAME "_act\0"		\
 	"progubo=tftp 200000 ${uboname};"				\
 		"protect off ${ubobot} ${ubotop};"			\
 		"erase ${ubobot} ${ubotop};"				\
 		"cp.b ${fileaddr} ${ubobot} ${filesize}\0"		\
 	"unlock=yes\0"							\
 	"post=echo !!! "CONFIG_BOARD_NAME" POWER ON SELF TEST !!!;"	\
 		"setenv bootdelay 1;"					\
 		"crc32 "__stringify(CONFIG_SYS_TEXT_BASE)" "		\
 			BOARD_POST_CRC32_END";"				\
 		"setenv bootcmd "CONFIG_BOARD_BOOTCMD";saveenv;reset\0"

 #define CONFIG_BOOTCOMMAND	"run post"

 /*
  * IPB Bus clocking configuration.
  */
 #define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */

 #if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
 /*
  * PCI Bus clocking configuration
  *
  * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
  * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
  * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
  */
 #define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2	/* define for 66MHz speed */
 #endif

 /*
  * I2C configuration
  */
 #define CONFIG_HARD_I2C			1	/* I2C with hardware support */
 #define CONFIG_SYS_I2C_MODULE		1	/* Select I2C module #1 or #2 */
 #define CONFIG_SYS_I2C_SPEED		100000	/* 100 kHz */
 #define CONFIG_SYS_I2C_SLAVE		0x7F

 /*
  * EEPROM configuration:
  *
  * O2DNT board is equiped with Ramtron FRAM device FM24CL16
  * 16 Kib Ferroelectric Nonvolatile serial RAM memory
  * organized as 2048 x 8 bits and addressable as eight I2C devices
  * 0x50 ... 0x57 each 256 bytes in size
  *
  */
 #define CONFIG_SYS_I2C_FRAM
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 /*
  * There is no write delay with FRAM, write operations are performed at bus
  * speed. Thus, no status polling or write delay is needed.
  */

 /*
  * Flash configuration
  */
 #define CONFIG_SYS_FLASH_CFI		1
 #define CONFIG_FLASH_CFI_DRIVER		1
 #define CONFIG_FLASH_16BIT
 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
 #define CONFIG_SYS_FLASH_CFI_AMD_RESET
 #define CONFIG_SYS_FLASH_EMPTY_INFO

 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks */
 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
 #define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Erase Timeout (in ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Write Timeout (in ms) */
 /* Timeout for Flash Clear Lock Bits (in ms) */
 #define CONFIG_SYS_FLASH_UNLOCK_TOUT	10000
 /* "Real" (hardware) sectors protection */
 #define CONFIG_SYS_FLASH_PROTECTION

 /*
  * Environment settings
  */
 #define CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_SIZE		0x20000
 #define CONFIG_ENV_SECT_SIZE	0x20000
 #define CONFIG_ENV_OVERWRITE	1
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00040000)

 /*
  * Memory map
  */
 #define CONFIG_SYS_MBAR		0xF0000000
 #define CONFIG_SYS_SDRAM_BASE	0x00000000
 #define CONFIG_SYS_DEFAULT_MBAR	0x80000000

 /* Use SRAM until RAM will be available */
 #define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
 #ifdef CONFIG_POST
 /* preserve space for the post_word at end of on-chip SRAM */
 #define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_POST_SIZE
 #else
 /* End of used area in DPRAM */
 #define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE
 #endif

 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
 					 GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_MONITOR_LEN		(192 << 10) /* 192 kB for Monitor */
 #define CONFIG_SYS_MALLOC_LEN		(128 << 10) /* 128 kB for malloc() */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)   /* Initial map for Linux */

 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT		1
 #endif

 /*
  * Ethernet configuration
  */
 #define CONFIG_MPC5xxx_FEC
 #define CONFIG_MPC5xxx_FEC_MII100
 #define CONFIG_PHY_ADDR			0x00
 #define CONFIG_RESET_PHY_R

 /*
  * GPIO configuration
  */
 #define CONFIG_SYS_GPIO_DATADIR		0x00000064 /* PSC1_2, PSC2_1,2 output */
 #define CONFIG_SYS_GPIO_OPENDRAIN	0x00000000 /* No open drain */
 #define CONFIG_SYS_GPIO_DATAVALUE	0x00000000 /* PSC1_1 to 1, rest to 0 */
 #define CONFIG_SYS_GPIO_ENABLE		0x00000064 /* PSC1_2, PSC2_1,2 enable */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
 #define CONFIG_CMDLINE_EDITING

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
 #endif
 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					 sizeof(CONFIG_SYS_PROMPT) + 16)
 /* max number of command args */
 #define CONFIG_SYS_MAXARGS		16
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE

 /* default load address */
 #define CONFIG_SYS_LOAD_ADDR		0x100000

 /* decrementer freq: 1 ms ticks */

 /*
  * Various low-level settings
  */
 #define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL		HID0_ICE

 #define CONFIG_SYS_BOOTCS_START		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
 #define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE

 #define CONFIG_BOARD_EARLY_INIT_R

 #define CONFIG_SYS_CS_BURST		0x00000000
 #define CONFIG_SYS_CS_DEADCYCLE		0x33333333

 /*
  * DT support
  */
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)

 #endif /* __O2D_CONFIG_H */
	/*
	* Common configuration options for ifm camera boards
	*
	* (C) Copyright 2005
	* Sebastien Cazaux, ifm electronic gmbh
	*
	* (C) Copyright 2012
	* DENX Software Engineering, Anatolij Gustschin <agust@denx.de>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __O2D_CONFIG_H
	#define __O2D_CONFIG_H

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_MPC5200
	#define CONFIG_DISPLAY_BOARDINFO

	#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* running at 33.000000MHz */

	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
	#if defined(CONFIG_CMD_KGDB)
	/* log base 2 of the above value */
	#define CONFIG_SYS_CACHELINE_SHIFT 5
	#endif

	/*
	#define CONFIG_POST (CONFIG_SYS_POST_MEMORY \| \
	CONFIG_SYS_POST_I2C)
	*/

	#ifdef CONFIG_POST
	/* preserve space for the post_word at end of on-chip SRAM */
	#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4)
	#endif

	/*
	* Serial console configuration
	*/
	#define CONFIG_PSC_CONSOLE 5 /* console is on PSC5 */
	#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
	#define CONFIG_SYS_BAUDRATE_TABLE \
	{ 9600, 19200, 38400, 57600, 115200, 230400 }

	/*
	* PCI Mapping:
	* 0x40000000 - 0x4fffffff - PCI Memory
	* 0x50000000 - 0x50ffffff - PCI IO Space
	*/
	#undef CONFIG_PCI
	#define CONFIG_PCI_PNP 1

	#define CONFIG_PCI_MEM_BUS 0x40000000
	#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
	#define CONFIG_PCI_MEM_SIZE 0x10000000

	#define CONFIG_PCI_IO_BUS 0x50000000
	#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
	#define CONFIG_PCI_IO_SIZE 0x01000000

	#define CONFIG_SYS_XLB_PIPELINING 1

	/* Partitions */
	#define CONFIG_MAC_PARTITION
	#define CONFIG_DOS_PARTITION
	#define CONFIG_ISO_PARTITION

	#define CONFIG_TIMESTAMP /* Print image info with timestamp */

	#define CONFIG_SYS_ALT_MEMTEST /* Much more complex memory test */

	/*
	* Supported commands
	*/
	#define CONFIG_CMD_EEPROM
	#ifdef CONFIG_PCI
	#define CONFIG_CMD_PCI
	#endif
	#ifdef CONFIG_POST
	#define CONFIG_CMD_DIAG
	#endif

	#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) \|\| (CONFIG_SYS_TEXT_BASE == 0xFF000000)
	/* Boot low with 16 or 32 MB Flash */
	#define CONFIG_SYS_LOWBOOT 1
	#elif (CONFIG_SYS_TEXT_BASE != 0x00100000)
	#error "CONFIG_SYS_TEXT_BASE value is invalid"
	#endif

	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */

	#define CONFIG_PREBOOT "run master"

	#undef CONFIG_BOOTARGS

	#if !defined(CONFIG_CONSOLE_DEV)
	#define CONFIG_CONSOLE_DEV "ttyPSC1"
	#endif

	/*
	* Default environment for booting old and new kernel versions
	*/
	#define CONFIG_IFM_DEFAULT_ENV_OLD \
	"flash_self_old=run ramargs addip addmem;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"flash_nfs_old=run nfsargs addip addmem;" \
	"bootm ${kernel_addr}\0" \
	"net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
	"run nfsargs addip addmem;" \
	"bootm ${kernel_addr_r}\0"

	#define CONFIG_IFM_DEFAULT_ENV_NEW \
	"fdt_addr_r=900000\0" \
	"fdt_file="CONFIG_BOARD_NAME"/"CONFIG_BOARD_NAME".dtb\0" \
	"flash_self=run ramargs addip addtty addmisc;" \
	"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
	"flash_nfs=run nfsargs addip addtty addmisc;" \
	"bootm ${kernel_addr} - ${fdt_addr}\0" \
	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
	"tftp ${fdt_addr_r} ${fdt_file}; " \
	"run nfsargs addip addtty addmisc;" \
	"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \

	#define CONFIG_IFM_DEFAULT_ENV_SETTINGS \
	"IOpin=0x64\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"addmem=setenv bootargs ${bootargs} ${memlimit}\0" \
	"addmisc=sete bootargs ${bootargs} ${miscargs}\0" \
	"addtty=sete bootargs ${bootargs} console=" \
	CONFIG_CONSOLE_DEV ",${baudrate}\0" \
	"bootfile="CONFIG_BOARD_NAME"/uImage_"CONFIG_BOARD_NAME"_act\0" \
	"kernel_addr_r=600000\0" \
	"initrd_high=0x03e00000\0" \
	"memlimit=mem="CONFIG_BOARD_MEM_LIMIT"M\0" \
	"memtest=mtest 0x00100000 "__stringify(CONFIG_SYS_MEMTEST_END)" 0 1\0" \
	"netdev=eth0\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"linuxname="CONFIG_BOARD_NAME"/uImage_"CONFIG_BOARD_NAME"_act\0"\
	"progLinux=tftp 200000 ${linuxname};erase ${linbot} ${lintop};" \
	"cp.b ${fileaddr} ${linbot} ${filesize}\0" \
	"ramname="CONFIG_BOARD_NAME"/uRamdisk_"CONFIG_BOARD_NAME"_act\0"\
	"progRam=tftp 200000 ${ramname};erase ${rambot} ${ramtop};" \
	"cp.b ${fileaddr} ${rambot} ${filesize}\0" \
	"jffname="CONFIG_BOARD_NAME"/uJFFS2_"CONFIG_BOARD_NAME"_act\0" \
	"progJff=tftp 200000 ${jffname};erase ${jffbot} ${jfftop};" \
	"cp.b ${fileaddr} ${jffbot} ${filesize}\0" \
	"rootpath=/opt/eldk/ppc_6xx\0" \
	"uboname=" CONFIG_BOARD_NAME \
	"/u-boot.bin_" CONFIG_BOARD_NAME "_act\0" \
	"progubo=tftp 200000 ${uboname};" \
	"protect off ${ubobot} ${ubotop};" \
	"erase ${ubobot} ${ubotop};" \
	"cp.b ${fileaddr} ${ubobot} ${filesize}\0" \
	"unlock=yes\0" \
	"post=echo !!! "CONFIG_BOARD_NAME" POWER ON SELF TEST !!!;" \
	"setenv bootdelay 1;" \
	"crc32 "__stringify(CONFIG_SYS_TEXT_BASE)" " \
	BOARD_POST_CRC32_END";" \
	"setenv bootcmd "CONFIG_BOARD_BOOTCMD";saveenv;reset\0"

	#define CONFIG_BOOTCOMMAND "run post"

	/*
	* IPB Bus clocking configuration.
	*/
	#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */

	#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
	/*
	* PCI Bus clocking configuration
	*
	* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
	* CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
	* of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
	*/
	#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
	#endif

	/*
	* I2C configuration
	*/
	#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
	#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */
	#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
	#define CONFIG_SYS_I2C_SLAVE 0x7F

	/*
	* EEPROM configuration:
	*
	* O2DNT board is equiped with Ramtron FRAM device FM24CL16
	* 16 Kib Ferroelectric Nonvolatile serial RAM memory
	* organized as 2048 x 8 bits and addressable as eight I2C devices
	* 0x50 ... 0x57 each 256 bytes in size
	*
	*/
	#define CONFIG_SYS_I2C_FRAM
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	/*
	* There is no write delay with FRAM, write operations are performed at bus
	* speed. Thus, no status polling or write delay is needed.
	*/

	/*
	* Flash configuration
	*/
	#define CONFIG_SYS_FLASH_CFI 1
	#define CONFIG_FLASH_CFI_DRIVER 1
	#define CONFIG_FLASH_16BIT
	#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
	#define CONFIG_SYS_FLASH_CFI_AMD_RESET
	#define CONFIG_SYS_FLASH_EMPTY_INFO

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
	#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Erase Timeout (in ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Write Timeout (in ms) */
	/* Timeout for Flash Clear Lock Bits (in ms) */
	#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000
	/* "Real" (hardware) sectors protection */
	#define CONFIG_SYS_FLASH_PROTECTION

	/*
	* Environment settings
	*/
	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_SIZE 0x20000
	#define CONFIG_ENV_SECT_SIZE 0x20000
	#define CONFIG_ENV_OVERWRITE 1
	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000)

	/*
	* Memory map
	*/
	#define CONFIG_SYS_MBAR 0xF0000000
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_DEFAULT_MBAR 0x80000000

	/* Use SRAM until RAM will be available */
	#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
	#ifdef CONFIG_POST
	/* preserve space for the post_word at end of on-chip SRAM */
	#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
	#else
	/* End of used area in DPRAM */
	#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
	#endif

	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
	GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* 192 kB for Monitor */
	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* 128 kB for malloc() */
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial map for Linux */

	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	#define CONFIG_SYS_RAMBOOT 1
	#endif

	/*
	* Ethernet configuration
	*/
	#define CONFIG_MPC5xxx_FEC
	#define CONFIG_MPC5xxx_FEC_MII100
	#define CONFIG_PHY_ADDR 0x00
	#define CONFIG_RESET_PHY_R

	/*
	* GPIO configuration
	*/
	#define CONFIG_SYS_GPIO_DATADIR 0x00000064 /* PSC1_2, PSC2_1,2 output */
	#define CONFIG_SYS_GPIO_OPENDRAIN 0x00000000 /* No open drain */
	#define CONFIG_SYS_GPIO_DATAVALUE 0x00000000 /* PSC1_1 to 1, rest to 0 */
	#define CONFIG_SYS_GPIO_ENABLE 0x00000064 /* PSC1_2, PSC2_1,2 enable */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_CMDLINE_EDITING

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)
	/* max number of command args */
	#define CONFIG_SYS_MAXARGS 16
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

	/* default load address */
	#define CONFIG_SYS_LOAD_ADDR 0x100000

	/* decrementer freq: 1 ms ticks */

	/*
	* Various low-level settings
	*/
	#define CONFIG_SYS_HID0_INIT HID0_ICE \| HID0_ICFI
	#define CONFIG_SYS_HID0_FINAL HID0_ICE

	#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
	#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE

	#define CONFIG_BOARD_EARLY_INIT_R

	#define CONFIG_SYS_CS_BURST 0x00000000
	#define CONFIG_SYS_CS_DEADCYCLE 0x33333333

	/*
	* DT support
	*/
	#define OF_CPU "PowerPC,5200@0"
	#define OF_SOC "soc5200@f0000000"
	#define OF_TBCLK (bd->bi_busfreq / 4)

	#endif /* __O2D_CONFIG_H */