| # SPDX-License-Identifier: GPL-2.0+ |
| # |
| # Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com> |
| |
| config INTEL_QUARK |
| bool |
| select HAVE_RMU |
| select ARCH_EARLY_INIT_R |
| select ARCH_MISC_INIT |
| imply ENABLE_MRC_CACHE |
| imply ETH_DESIGNWARE |
| imply ICH_SPI |
| imply INTEL_ICH6_GPIO |
| imply MMC |
| imply MMC_PCI |
| imply MMC_SDHCI |
| imply MMC_SDHCI_SDMA |
| imply SPI_FLASH |
| imply SYS_NS16550 |
| imply USB |
| imply USB_EHCI_HCD |
| |
| if INTEL_QUARK |
| |
| config HAVE_RMU |
| bool "Add a Remote Management Unit (RMU) binary" |
| help |
| Select this option to add a Remote Management Unit (RMU) binary |
| to the resulting U-Boot image. It is a data block (up to 64K) of |
| machine-specific code which must be put in the flash for the RMU |
| within the Quark SoC processor to access when powered up before |
| system BIOS is executed. |
| |
| config RMU_FILE |
| string "Remote Management Unit (RMU) binary filename" |
| depends on HAVE_RMU |
| default "rmu.bin" |
| help |
| The filename of the file to use as Remote Management Unit (RMU) |
| binary in the board directory. |
| |
| config RMU_ADDR |
| hex "Remote Management Unit (RMU) binary location" |
| depends on HAVE_RMU |
| default 0xfff00000 |
| help |
| The location of the RMU binary is determined by a strap. It must be |
| put in flash at a location matching the strap-determined base address. |
| |
| The default base address of 0xfff00000 indicates that the binary must |
| be located at offset 0 from the beginning of a 1MB flash device. |
| |
| config HAVE_CMC |
| bool |
| default HAVE_RMU |
| |
| config CMC_FILE |
| string |
| depends on HAVE_CMC |
| default RMU_FILE |
| |
| config CMC_ADDR |
| hex |
| depends on HAVE_CMC |
| default RMU_ADDR |
| |
| config ESRAM_BASE |
| hex |
| default 0x80000000 |
| help |
| Embedded SRAM (eSRAM) memory-mapped base address. |
| |
| config PCIE_ECAM_BASE |
| hex |
| default 0xe0000000 |
| |
| config RCBA_BASE |
| hex |
| default 0xfed1c000 |
| help |
| Root Complex register block memory-mapped base address. |
| |
| config ACPI_PM1_BASE |
| hex |
| default 0x1000 |
| help |
| ACPI Power Managment 1 (PM1) i/o-mapped base address. |
| This device is defined in ACPI specification, with 16 bytes in size. |
| |
| config ACPI_PBLK_BASE |
| hex |
| default 0x1010 |
| help |
| ACPI Processor Block (PBLK) i/o-mapped base address. |
| This device is defined in ACPI specification, with 16 bytes in size. |
| |
| config SPI_DMA_BASE |
| hex |
| default 0x1020 |
| help |
| SPI DMA i/o-mapped base address. |
| |
| config GPIO_BASE |
| hex |
| default 0x1080 |
| help |
| GPIO i/o-mapped base address. |
| |
| config ACPI_GPE0_BASE |
| hex |
| default 0x1100 |
| help |
| ACPI General Purpose Event 0 (GPE0) i/o-mapped base address. |
| This device is defined in ACPI specification, with 64 bytes in size. |
| |
| config WDT_BASE |
| hex |
| default 0x1140 |
| help |
| Watchdog timer i/o-mapped base address. |
| |
| config SYS_CAR_ADDR |
| hex |
| default ESRAM_BASE |
| |
| config SYS_CAR_SIZE |
| hex |
| default 0x8000 |
| help |
| Space in bytes in eSRAM used as Cache-As-ARM (CAR). |
| Note this size must not exceed eSRAM's total size. |
| |
| config X86_TSC_TIMER_EARLY_FREQ |
| int |
| default 400 |
| |
| endif |