blob: 45263e6b44ca71c5b38720837ced4d5ad80b2cbd [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2010
* Eastman Kodak Company, <www.kodak.com>
* Michael Zaidman, <michael.zaidman@kodak.com>
*
* The code is based on the cpu/mpc83xx/ecc.c written by
* Dave Liu <daveliu@freescale.com>
*/
#include <common.h>
#include <cpu_func.h>
#include <irq_func.h>
#include <log.h>
#include <mpc83xx.h>
#include <watchdog.h>
#include <asm/io.h>
#include <post.h>
#if CFG_POST & CONFIG_SYS_POST_ECC
/*
* We use the RAW I/O accessors where possible in order to
* achieve performance goal, since the test's execution time
* affects the board start up time.
*/
static inline void ecc_clear(ddr83xx_t *ddr)
{
/* Clear capture registers */
__raw_writel(0, &ddr->capture_address);
__raw_writel(0, &ddr->capture_data_hi);
__raw_writel(0, &ddr->capture_data_lo);
__raw_writel(0, &ddr->capture_ecc);
__raw_writel(0, &ddr->capture_attributes);
/* Clear SBEC and set SBET to 1 */
out_be32(&ddr->err_sbe, 1 << ECC_ERROR_MAN_SBET_SHIFT);
/* Clear Error Detect register */
out_be32(&ddr->err_detect, ECC_ERROR_DETECT_MME |\
ECC_ERROR_DETECT_MBE |\
ECC_ERROR_DETECT_SBE |\
ECC_ERROR_DETECT_MSE);
isync();
}
int ecc_post_test(int flags)
{
int ret = 0;
int int_state;
int errbit;
u32 pattern[2], writeback[2], retval[2];
ddr83xx_t *ddr = &((immap_t *)CONFIG_SYS_IMMR)->ddr;
volatile u64 *addr = (u64 *)CONFIG_SYS_POST_ECC_START_ADDR;
/* The pattern is written into memory to generate error */
pattern[0] = 0xfedcba98UL;
pattern[1] = 0x76543210UL;
/* After injecting error, re-initialize the memory with the value */
writeback[0] = ~pattern[0];
writeback[1] = ~pattern[1];
/* Check if ECC is enabled */
if (__raw_readl(&ddr->err_disable) & ECC_ERROR_ENABLE) {
debug("DDR's ECC is not enabled, skipping the ECC POST.\n");
return 0;
}
int_state = disable_interrupts();
icache_enable();
for (addr = (u64*)CONFIG_SYS_POST_ECC_START_ADDR, errbit=0;
addr < (u64*)CONFIG_SYS_POST_ECC_STOP_ADDR; addr++, errbit++ ) {
schedule();
ecc_clear(ddr);
/* Enable error injection */
setbits_be32(&ddr->ecc_err_inject, ECC_ERR_INJECT_EIEN);
sync();
isync();
/* Set bit to be injected */
if (errbit < 32) {
__raw_writel(1 << errbit, &ddr->data_err_inject_lo);
__raw_writel(0, &ddr->data_err_inject_hi);
} else {
__raw_writel(0, &ddr->data_err_inject_lo);
__raw_writel(1<<(errbit-32), &ddr->data_err_inject_hi);
}
sync();
isync();
/* Write memory location injecting SBE */
ppcDWstore((u32*)addr, pattern);
sync();
/* Disable error injection */
clrbits_be32(&ddr->ecc_err_inject, ECC_ERR_INJECT_EIEN);
sync();
isync();
/* Data read should generate SBE */
ppcDWload((u32*)addr, retval);
sync();
if (!(__raw_readl(&ddr->err_detect) & ECC_ERROR_DETECT_SBE) ||
(__raw_readl(&ddr->data_err_inject_hi) !=
(__raw_readl(&ddr->capture_data_hi) ^ pattern[0])) ||
(__raw_readl(&ddr->data_err_inject_lo) !=
(__raw_readl(&ddr->capture_data_lo) ^ pattern[1]))) {
post_log("ECC failed to detect SBE error at %08x, "
"SBE injection mask %08x-%08x, wrote "
"%08x-%08x, read %08x-%08x\n", addr,
ddr->data_err_inject_hi,
ddr->data_err_inject_lo,
pattern[0], pattern[1],
retval[0], retval[1]);
printf("ERR_DETECT Reg: %08x\n", ddr->err_detect);
printf("ECC CAPTURE_DATA Reg: %08x-%08x\n",
ddr->capture_data_hi, ddr->capture_data_lo);
ret = 1;
break;
}
/* Re-initialize the ECC memory */
ppcDWstore((u32*)addr, writeback);
sync();
isync();
errbit %= 63;
}
ecc_clear(ddr);
icache_disable();
if (int_state)
enable_interrupts();
return ret;
}
#endif