blob: 9f648342ea33a4bfd6b9b55e5ef6f2e482e2c922 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/* Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
* Hayden Fraser (Hayden.Fraser@freescale.com)
*/
#ifndef _M5253DEMO_H
#define _M5253DEMO_H
#include <linux/stringify.h>
#define CONFIG_SYS_UART_PORT (0)
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
#define LDS_BOARD_TEXT \
. = DEFINED(env_offset) ? env_offset : .; \
env/embedded.o(.text*);
#ifdef CONFIG_DRIVER_DM9000
# define CONFIG_DM9000_BASE (CONFIG_SYS_CS1_BASE | 0x300)
# define DM9000_IO CONFIG_DM9000_BASE
# define DM9000_DATA (CONFIG_DM9000_BASE + 4)
# undef CONFIG_DM9000_DEBUG
# define CONFIG_DM9000_BYTE_SWAPPED
# define CONFIG_OVERWRITE_ETHADDR_ONCE
# define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
"loadaddr=10000\0" \
"u-boot=u-boot.bin\0" \
"load=tftp ${loadaddr) ${u-boot}\0" \
"upd=run load; run prog\0" \
"prog=prot off 0xff800000 0xff82ffff;" \
"era 0xff800000 0xff82ffff;" \
"cp.b ${loadaddr} 0xff800000 ${filesize};" \
"save\0" \
""
#endif
#define CONFIG_HOSTNAME "M5253DEMO"
/* I2C */
#define CONFIG_SYS_I2C_PINMUX_REG (*(u32 *) (CONFIG_SYS_MBAR+0x19C))
#define CONFIG_SYS_I2C_PINMUX_CLR (0xFFFFE7FF)
#define CONFIG_SYS_I2C_PINMUX_SET (0)
#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */
#define CONFIG_SYS_FAST_CLK
#ifdef CONFIG_SYS_FAST_CLK
# define CONFIG_SYS_PLLCR 0x1243E054
# define CONFIG_SYS_CLK 140000000
#else
# define CONFIG_SYS_PLLCR 0x135a4140
# define CONFIG_SYS_CLK 70000000
#endif
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */
#define CONFIG_SYS_MBAR2 0x80000000 /* Module Base Addrs 2 */
/*
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
/*
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
#define CONFIG_SYS_MONITOR_LEN 0x40000
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
/* FLASH organization */
#define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE)
#define FLASH_SST6401B 0x200
#define SST_ID_xF6401B 0x236D236D
#ifdef CONFIG_SYS_FLASH_CFI
/*
* Unable to use CFI driver, due to incompatible sector erase command by SST.
* Amd/Atmel use 0x30 for sector erase, SST use 0x50.
* 0x30 is block erase in SST
*/
# define CONFIG_SYS_FLASH_SIZE 0x800000
#else
# define CONFIG_SYS_SST_SECT 2048
# define CONFIG_SYS_SST_SECTSZ 0x1000
#endif
/* Cache Configuration */
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 4)
#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM)
#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \
CF_ADDRMASK(8) | \
CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \
CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \
CF_CACR_DBWE)
/* Port configuration */
#define CONFIG_SYS_FECI2C 0xF0
#define CONFIG_SYS_CS0_BASE 0xFF800000
#define CONFIG_SYS_CS0_MASK 0x007F0021
#define CONFIG_SYS_CS0_CTRL 0x00001D80
#define CONFIG_SYS_CS1_BASE 0xE0000000
#define CONFIG_SYS_CS1_MASK 0x00000001
#define CONFIG_SYS_CS1_CTRL 0x00003DD8
/*-----------------------------------------------------------------------
* Port configuration
*/
#define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */
#define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */
#define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */
#define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */
#define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */
#define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */
#define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */
#endif /* _M5253DEMO_H */