blob: 31279fc0cbf974804b87ece5e32dfc8af063cdc9 [file] [log] [blame]
.. SPDX-License-Identifier: GPL-2.0+
.. Copyright 2020, Heinrich Schuchardt <xypron.glpk@gmx.de>
bootefi command
===============
Synopsis
--------
::
bootefi [image_addr] [fdt_addr]
bootefi bootmgr [fdt_addr]
bootefi hello [fdt_addr]
bootefi selftest [fdt_addr]
Description
-----------
The *bootefi* command is used to launch a UEFI binary which can be either of
* UEFI application
* UEFI boot services driver
* UEFI run-time services driver
An operating system requires a hardware description which can either be
presented as ACPI table (CONFIG\_GENERATE\_ACPI\_TABLE=y) or as device-tree.
The load address of the device-tree may be provided as parameter *fdt\_addr*. If
this address is not specified, the bootefi command will try to fall back in
sequence to:
* the device-tree specified by environment variable *fdt\_addr*
* the device-tree specified by environment variable *fdtcontroladdr*
The load address of the binary is specified by parameter *image_address*. A
command sequence to run a UEFI application might look like
::
load mmc 0:2 $fdt_addr_r dtb
load mmc 0:1 $kernel_addr_r /EFI/grub/grubaa64.efi
bootefi $kernel_addr_r $fdt_addr_r
The last file loaded defines the image file path in the loaded image protocol.
Hence the executable should always be loaded last.
The value of the environment variable *bootargs* is converted from UTF-8 to
UTF-16 and passed as load options in the loaded image protocol to the UEFI
binary.
Note
UEFI binaries that are contained in FIT images are launched via the
*bootm* command.
UEFI boot manager
'''''''''''''''''
The UEFI boot manager is invoked by the *bootefi bootmgr* sub-command.
Here boot options are defined by UEFI variables with a name consisting of the
letters *Boot* followed by a four digit hexadecimal number, e.g. *Boot0001* or
*BootA03E*. The boot variable defines a label, the device path of the binary to
execute as well as the load options passed in the loaded image protocol.
If the UEFI variable *BootNext* is defined, it specifies the number of the boot
option to execute next. If no binary can be loaded via *BootNext* the variable
*BootOrder* specifies in which sequence boot options shalled be tried.
The values of these variables can be managed using the U-Boot command
*efidebug*.
UEFI hello world application
''''''''''''''''''''''''''''
U-Boot can be compiled with a hello world application that can be launched using
the *bootefi hello* sub-command. A session might look like
::
=> setenv bootargs 'Greetings to the world'
=> bootefi hello
Booting /MemoryMapped(0x0,0x10001000,0x1000)
Hello, world!
Running on UEFI 2.8
Have SMBIOS table
Have device tree
Load options: Greetings to the world
UEFI selftest
'''''''''''''
U-Boot can be compiled with UEFI unit tests. These unit tests are invoked using
the *bootefi selftest* sub-command.
Which unit test is executed is controlled by the environment variable
*efi\_selftest*. If this variable is not set, all unit tests that are not marked
as 'on request' are executed.
To show a list of the available unit tests the value *list* can be used
::
=> setenv efi_selftest list
=> bootefi selftest
Available tests:
'block image transfer' - on request
'block device'
'configuration tables'
...
A single test is selected for execution by setting the *efi\_selftest*
environment variable to match one of the listed identifiers
::
=> setenv efi_selftest 'block image transfer'
=> bootefi selftest
Some of the tests execute the ExitBootServices() UEFI boot service and will not
return to the command line but require a board reset.
Configuration
-------------
To use the *bootefi* command you must specify CONFIG\_CMD\_BOOTEFI=y.
The *bootefi bootmgr* sub-command requries CMD\_BOOTEFI\_BOOTMGR=y.
The *bootefi hello* sub-command requries CMD\_BOOTEFI\_HELLO=y.
The *bootefi selftest* sub-command depends on CMD\_BOOTEFI\_SELFTEST=y.
See also
--------
* *bootm* for launching UEFI binaries packed in FIT images
* :doc:`booti<booti>`, *bootm*, *bootz* for launching a Linux kernel without
using the UEFI sub-system
* *efidebug* for setting UEFI boot variables and boot options