| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * SDM845 SoC device tree source |
| * |
| * Copyright (c) 2018, The Linux Foundation. All rights reserved. |
| */ |
| |
| #include <dt-bindings/clock/qcom,camcc-sdm845.h> |
| #include <dt-bindings/clock/qcom,dispcc-sdm845.h> |
| #include <dt-bindings/clock/qcom,gcc-sdm845.h> |
| #include <dt-bindings/clock/qcom,gpucc-sdm845.h> |
| #include <dt-bindings/clock/qcom,lpass-sdm845.h> |
| #include <dt-bindings/clock/qcom,rpmh.h> |
| #include <dt-bindings/clock/qcom,videocc-sdm845.h> |
| #include <dt-bindings/dma/qcom-gpi.h> |
| #include <dt-bindings/firmware/qcom,scm.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interconnect/qcom,osm-l3.h> |
| #include <dt-bindings/interconnect/qcom,sdm845.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/phy/phy-qcom-qmp.h> |
| #include <dt-bindings/phy/phy-qcom-qusb2.h> |
| #include <dt-bindings/power/qcom-rpmpd.h> |
| #include <dt-bindings/reset/qcom,sdm845-aoss.h> |
| #include <dt-bindings/reset/qcom,sdm845-pdc.h> |
| #include <dt-bindings/soc/qcom,apr.h> |
| #include <dt-bindings/soc/qcom,rpmh-rsc.h> |
| #include <dt-bindings/clock/qcom,gcc-sdm845.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| / { |
| interrupt-parent = <&intc>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| aliases { |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| i2c2 = &i2c2; |
| i2c3 = &i2c3; |
| i2c4 = &i2c4; |
| i2c5 = &i2c5; |
| i2c6 = &i2c6; |
| i2c7 = &i2c7; |
| i2c8 = &i2c8; |
| i2c9 = &i2c9; |
| i2c10 = &i2c10; |
| i2c11 = &i2c11; |
| i2c12 = &i2c12; |
| i2c13 = &i2c13; |
| i2c14 = &i2c14; |
| i2c15 = &i2c15; |
| spi0 = &spi0; |
| spi1 = &spi1; |
| spi2 = &spi2; |
| spi3 = &spi3; |
| spi4 = &spi4; |
| spi5 = &spi5; |
| spi6 = &spi6; |
| spi7 = &spi7; |
| spi8 = &spi8; |
| spi9 = &spi9; |
| spi10 = &spi10; |
| spi11 = &spi11; |
| spi12 = &spi12; |
| spi13 = &spi13; |
| spi14 = &spi14; |
| spi15 = &spi15; |
| }; |
| |
| chosen { }; |
| |
| clocks { |
| xo_board: xo-board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <38400000>; |
| clock-output-names = "xo_board"; |
| }; |
| |
| sleep_clk: sleep-clk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32764>; |
| }; |
| }; |
| |
| cpus: cpus { |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| CPU0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo385"; |
| reg = <0x0 0x0>; |
| clocks = <&cpufreq_hw 0>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <611>; |
| dynamic-power-coefficient = <154>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| operating-points-v2 = <&cpu0_opp_table>; |
| interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>, |
| <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; |
| power-domains = <&CPU_PD0>; |
| power-domain-names = "psci"; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_0>; |
| L2_0: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| next-level-cache = <&L3_0>; |
| L3_0: l3-cache { |
| compatible = "cache"; |
| cache-level = <3>; |
| cache-unified; |
| }; |
| }; |
| }; |
| |
| CPU1: cpu@100 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo385"; |
| reg = <0x0 0x100>; |
| clocks = <&cpufreq_hw 0>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <611>; |
| dynamic-power-coefficient = <154>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| operating-points-v2 = <&cpu0_opp_table>; |
| interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>, |
| <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; |
| power-domains = <&CPU_PD1>; |
| power-domain-names = "psci"; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_100>; |
| L2_100: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU2: cpu@200 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo385"; |
| reg = <0x0 0x200>; |
| clocks = <&cpufreq_hw 0>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <611>; |
| dynamic-power-coefficient = <154>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| operating-points-v2 = <&cpu0_opp_table>; |
| interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>, |
| <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; |
| power-domains = <&CPU_PD2>; |
| power-domain-names = "psci"; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_200>; |
| L2_200: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU3: cpu@300 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo385"; |
| reg = <0x0 0x300>; |
| clocks = <&cpufreq_hw 0>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <611>; |
| dynamic-power-coefficient = <154>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| operating-points-v2 = <&cpu0_opp_table>; |
| interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>, |
| <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; |
| #cooling-cells = <2>; |
| power-domains = <&CPU_PD3>; |
| power-domain-names = "psci"; |
| next-level-cache = <&L2_300>; |
| L2_300: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU4: cpu@400 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo385"; |
| reg = <0x0 0x400>; |
| clocks = <&cpufreq_hw 1>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| dynamic-power-coefficient = <442>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| operating-points-v2 = <&cpu4_opp_table>; |
| interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>, |
| <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; |
| power-domains = <&CPU_PD4>; |
| power-domain-names = "psci"; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_400>; |
| L2_400: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU5: cpu@500 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo385"; |
| reg = <0x0 0x500>; |
| clocks = <&cpufreq_hw 1>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| dynamic-power-coefficient = <442>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| operating-points-v2 = <&cpu4_opp_table>; |
| interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>, |
| <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; |
| power-domains = <&CPU_PD5>; |
| power-domain-names = "psci"; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_500>; |
| L2_500: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU6: cpu@600 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo385"; |
| reg = <0x0 0x600>; |
| clocks = <&cpufreq_hw 1>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| dynamic-power-coefficient = <442>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| operating-points-v2 = <&cpu4_opp_table>; |
| interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>, |
| <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; |
| power-domains = <&CPU_PD6>; |
| power-domain-names = "psci"; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_600>; |
| L2_600: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU7: cpu@700 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo385"; |
| reg = <0x0 0x700>; |
| clocks = <&cpufreq_hw 1>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| dynamic-power-coefficient = <442>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| operating-points-v2 = <&cpu4_opp_table>; |
| interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>, |
| <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; |
| power-domains = <&CPU_PD7>; |
| power-domain-names = "psci"; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_700>; |
| L2_700: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| cpu-map { |
| cluster0 { |
| core0 { |
| cpu = <&CPU0>; |
| }; |
| |
| core1 { |
| cpu = <&CPU1>; |
| }; |
| |
| core2 { |
| cpu = <&CPU2>; |
| }; |
| |
| core3 { |
| cpu = <&CPU3>; |
| }; |
| |
| core4 { |
| cpu = <&CPU4>; |
| }; |
| |
| core5 { |
| cpu = <&CPU5>; |
| }; |
| |
| core6 { |
| cpu = <&CPU6>; |
| }; |
| |
| core7 { |
| cpu = <&CPU7>; |
| }; |
| }; |
| }; |
| |
| cpu_idle_states: idle-states { |
| entry-method = "psci"; |
| |
| LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "little-rail-power-collapse"; |
| arm,psci-suspend-param = <0x40000004>; |
| entry-latency-us = <350>; |
| exit-latency-us = <461>; |
| min-residency-us = <1890>; |
| local-timer-stop; |
| }; |
| |
| BIG_CPU_SLEEP_0: cpu-sleep-1-0 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "big-rail-power-collapse"; |
| arm,psci-suspend-param = <0x40000004>; |
| entry-latency-us = <264>; |
| exit-latency-us = <621>; |
| min-residency-us = <952>; |
| local-timer-stop; |
| }; |
| }; |
| |
| domain-idle-states { |
| CLUSTER_SLEEP_0: cluster-sleep-0 { |
| compatible = "domain-idle-state"; |
| arm,psci-suspend-param = <0x4100c244>; |
| entry-latency-us = <3263>; |
| exit-latency-us = <6562>; |
| min-residency-us = <9987>; |
| }; |
| }; |
| }; |
| |
| firmware { |
| scm { |
| compatible = "qcom,scm-sdm845", "qcom,scm"; |
| }; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| /* We expect the bootloader to fill in the size */ |
| reg = <0 0x80000000 0 0>; |
| }; |
| |
| cpu0_opp_table: opp-table-cpu0 { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| |
| cpu0_opp1: opp-300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| opp-peak-kBps = <800000 4800000>; |
| }; |
| |
| cpu0_opp2: opp-403200000 { |
| opp-hz = /bits/ 64 <403200000>; |
| opp-peak-kBps = <800000 4800000>; |
| }; |
| |
| cpu0_opp3: opp-480000000 { |
| opp-hz = /bits/ 64 <480000000>; |
| opp-peak-kBps = <800000 6451200>; |
| }; |
| |
| cpu0_opp4: opp-576000000 { |
| opp-hz = /bits/ 64 <576000000>; |
| opp-peak-kBps = <800000 6451200>; |
| }; |
| |
| cpu0_opp5: opp-652800000 { |
| opp-hz = /bits/ 64 <652800000>; |
| opp-peak-kBps = <800000 7680000>; |
| }; |
| |
| cpu0_opp6: opp-748800000 { |
| opp-hz = /bits/ 64 <748800000>; |
| opp-peak-kBps = <1804000 9216000>; |
| }; |
| |
| cpu0_opp7: opp-825600000 { |
| opp-hz = /bits/ 64 <825600000>; |
| opp-peak-kBps = <1804000 9216000>; |
| }; |
| |
| cpu0_opp8: opp-902400000 { |
| opp-hz = /bits/ 64 <902400000>; |
| opp-peak-kBps = <1804000 10444800>; |
| }; |
| |
| cpu0_opp9: opp-979200000 { |
| opp-hz = /bits/ 64 <979200000>; |
| opp-peak-kBps = <1804000 11980800>; |
| }; |
| |
| cpu0_opp10: opp-1056000000 { |
| opp-hz = /bits/ 64 <1056000000>; |
| opp-peak-kBps = <1804000 11980800>; |
| }; |
| |
| cpu0_opp11: opp-1132800000 { |
| opp-hz = /bits/ 64 <1132800000>; |
| opp-peak-kBps = <2188000 13516800>; |
| }; |
| |
| cpu0_opp12: opp-1228800000 { |
| opp-hz = /bits/ 64 <1228800000>; |
| opp-peak-kBps = <2188000 15052800>; |
| }; |
| |
| cpu0_opp13: opp-1324800000 { |
| opp-hz = /bits/ 64 <1324800000>; |
| opp-peak-kBps = <2188000 16588800>; |
| }; |
| |
| cpu0_opp14: opp-1420800000 { |
| opp-hz = /bits/ 64 <1420800000>; |
| opp-peak-kBps = <3072000 18124800>; |
| }; |
| |
| cpu0_opp15: opp-1516800000 { |
| opp-hz = /bits/ 64 <1516800000>; |
| opp-peak-kBps = <3072000 19353600>; |
| }; |
| |
| cpu0_opp16: opp-1612800000 { |
| opp-hz = /bits/ 64 <1612800000>; |
| opp-peak-kBps = <4068000 19353600>; |
| }; |
| |
| cpu0_opp17: opp-1689600000 { |
| opp-hz = /bits/ 64 <1689600000>; |
| opp-peak-kBps = <4068000 20889600>; |
| }; |
| |
| cpu0_opp18: opp-1766400000 { |
| opp-hz = /bits/ 64 <1766400000>; |
| opp-peak-kBps = <4068000 22425600>; |
| }; |
| }; |
| |
| cpu4_opp_table: opp-table-cpu4 { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| |
| cpu4_opp1: opp-300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| opp-peak-kBps = <800000 4800000>; |
| }; |
| |
| cpu4_opp2: opp-403200000 { |
| opp-hz = /bits/ 64 <403200000>; |
| opp-peak-kBps = <800000 4800000>; |
| }; |
| |
| cpu4_opp3: opp-480000000 { |
| opp-hz = /bits/ 64 <480000000>; |
| opp-peak-kBps = <1804000 4800000>; |
| }; |
| |
| cpu4_opp4: opp-576000000 { |
| opp-hz = /bits/ 64 <576000000>; |
| opp-peak-kBps = <1804000 4800000>; |
| }; |
| |
| cpu4_opp5: opp-652800000 { |
| opp-hz = /bits/ 64 <652800000>; |
| opp-peak-kBps = <1804000 4800000>; |
| }; |
| |
| cpu4_opp6: opp-748800000 { |
| opp-hz = /bits/ 64 <748800000>; |
| opp-peak-kBps = <1804000 4800000>; |
| }; |
| |
| cpu4_opp7: opp-825600000 { |
| opp-hz = /bits/ 64 <825600000>; |
| opp-peak-kBps = <2188000 9216000>; |
| }; |
| |
| cpu4_opp8: opp-902400000 { |
| opp-hz = /bits/ 64 <902400000>; |
| opp-peak-kBps = <2188000 9216000>; |
| }; |
| |
| cpu4_opp9: opp-979200000 { |
| opp-hz = /bits/ 64 <979200000>; |
| opp-peak-kBps = <2188000 9216000>; |
| }; |
| |
| cpu4_opp10: opp-1056000000 { |
| opp-hz = /bits/ 64 <1056000000>; |
| opp-peak-kBps = <3072000 9216000>; |
| }; |
| |
| cpu4_opp11: opp-1132800000 { |
| opp-hz = /bits/ 64 <1132800000>; |
| opp-peak-kBps = <3072000 11980800>; |
| }; |
| |
| cpu4_opp12: opp-1209600000 { |
| opp-hz = /bits/ 64 <1209600000>; |
| opp-peak-kBps = <4068000 11980800>; |
| }; |
| |
| cpu4_opp13: opp-1286400000 { |
| opp-hz = /bits/ 64 <1286400000>; |
| opp-peak-kBps = <4068000 11980800>; |
| }; |
| |
| cpu4_opp14: opp-1363200000 { |
| opp-hz = /bits/ 64 <1363200000>; |
| opp-peak-kBps = <4068000 15052800>; |
| }; |
| |
| cpu4_opp15: opp-1459200000 { |
| opp-hz = /bits/ 64 <1459200000>; |
| opp-peak-kBps = <4068000 15052800>; |
| }; |
| |
| cpu4_opp16: opp-1536000000 { |
| opp-hz = /bits/ 64 <1536000000>; |
| opp-peak-kBps = <5412000 15052800>; |
| }; |
| |
| cpu4_opp17: opp-1612800000 { |
| opp-hz = /bits/ 64 <1612800000>; |
| opp-peak-kBps = <5412000 15052800>; |
| }; |
| |
| cpu4_opp18: opp-1689600000 { |
| opp-hz = /bits/ 64 <1689600000>; |
| opp-peak-kBps = <5412000 19353600>; |
| }; |
| |
| cpu4_opp19: opp-1766400000 { |
| opp-hz = /bits/ 64 <1766400000>; |
| opp-peak-kBps = <6220000 19353600>; |
| }; |
| |
| cpu4_opp20: opp-1843200000 { |
| opp-hz = /bits/ 64 <1843200000>; |
| opp-peak-kBps = <6220000 19353600>; |
| }; |
| |
| cpu4_opp21: opp-1920000000 { |
| opp-hz = /bits/ 64 <1920000000>; |
| opp-peak-kBps = <7216000 19353600>; |
| }; |
| |
| cpu4_opp22: opp-1996800000 { |
| opp-hz = /bits/ 64 <1996800000>; |
| opp-peak-kBps = <7216000 20889600>; |
| }; |
| |
| cpu4_opp23: opp-2092800000 { |
| opp-hz = /bits/ 64 <2092800000>; |
| opp-peak-kBps = <7216000 20889600>; |
| }; |
| |
| cpu4_opp24: opp-2169600000 { |
| opp-hz = /bits/ 64 <2169600000>; |
| opp-peak-kBps = <7216000 20889600>; |
| }; |
| |
| cpu4_opp25: opp-2246400000 { |
| opp-hz = /bits/ 64 <2246400000>; |
| opp-peak-kBps = <7216000 20889600>; |
| }; |
| |
| cpu4_opp26: opp-2323200000 { |
| opp-hz = /bits/ 64 <2323200000>; |
| opp-peak-kBps = <7216000 20889600>; |
| }; |
| |
| cpu4_opp27: opp-2400000000 { |
| opp-hz = /bits/ 64 <2400000000>; |
| opp-peak-kBps = <7216000 22425600>; |
| }; |
| |
| cpu4_opp28: opp-2476800000 { |
| opp-hz = /bits/ 64 <2476800000>; |
| opp-peak-kBps = <7216000 22425600>; |
| }; |
| |
| cpu4_opp29: opp-2553600000 { |
| opp-hz = /bits/ 64 <2553600000>; |
| opp-peak-kBps = <7216000 22425600>; |
| }; |
| |
| cpu4_opp30: opp-2649600000 { |
| opp-hz = /bits/ 64 <2649600000>; |
| opp-peak-kBps = <7216000 22425600>; |
| }; |
| |
| cpu4_opp31: opp-2745600000 { |
| opp-hz = /bits/ 64 <2745600000>; |
| opp-peak-kBps = <7216000 25497600>; |
| }; |
| |
| cpu4_opp32: opp-2803200000 { |
| opp-hz = /bits/ 64 <2803200000>; |
| opp-peak-kBps = <7216000 25497600>; |
| }; |
| }; |
| |
| dsi_opp_table: opp-table-dsi { |
| compatible = "operating-points-v2"; |
| |
| opp-19200000 { |
| opp-hz = /bits/ 64 <19200000>; |
| required-opps = <&rpmhpd_opp_min_svs>; |
| }; |
| |
| opp-180000000 { |
| opp-hz = /bits/ 64 <180000000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-275000000 { |
| opp-hz = /bits/ 64 <275000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| |
| opp-328580000 { |
| opp-hz = /bits/ 64 <328580000>; |
| required-opps = <&rpmhpd_opp_svs_l1>; |
| }; |
| |
| opp-358000000 { |
| opp-hz = /bits/ 64 <358000000>; |
| required-opps = <&rpmhpd_opp_nom>; |
| }; |
| }; |
| |
| qspi_opp_table: opp-table-qspi { |
| compatible = "operating-points-v2"; |
| |
| opp-19200000 { |
| opp-hz = /bits/ 64 <19200000>; |
| required-opps = <&rpmhpd_opp_min_svs>; |
| }; |
| |
| opp-100000000 { |
| opp-hz = /bits/ 64 <100000000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-150000000 { |
| opp-hz = /bits/ 64 <150000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| |
| opp-300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| required-opps = <&rpmhpd_opp_nom>; |
| }; |
| }; |
| |
| qup_opp_table: opp-table-qup { |
| compatible = "operating-points-v2"; |
| |
| opp-50000000 { |
| opp-hz = /bits/ 64 <50000000>; |
| required-opps = <&rpmhpd_opp_min_svs>; |
| }; |
| |
| opp-75000000 { |
| opp-hz = /bits/ 64 <75000000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-100000000 { |
| opp-hz = /bits/ 64 <100000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| |
| opp-128000000 { |
| opp-hz = /bits/ 64 <128000000>; |
| required-opps = <&rpmhpd_opp_nom>; |
| }; |
| }; |
| |
| pmu { |
| compatible = "arm,armv8-pmuv3"; |
| interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| psci: psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| |
| CPU_PD0: power-domain-cpu0 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD>; |
| domain-idle-states = <&LITTLE_CPU_SLEEP_0>; |
| }; |
| |
| CPU_PD1: power-domain-cpu1 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD>; |
| domain-idle-states = <&LITTLE_CPU_SLEEP_0>; |
| }; |
| |
| CPU_PD2: power-domain-cpu2 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD>; |
| domain-idle-states = <&LITTLE_CPU_SLEEP_0>; |
| }; |
| |
| CPU_PD3: power-domain-cpu3 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD>; |
| domain-idle-states = <&LITTLE_CPU_SLEEP_0>; |
| }; |
| |
| CPU_PD4: power-domain-cpu4 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD>; |
| domain-idle-states = <&BIG_CPU_SLEEP_0>; |
| }; |
| |
| CPU_PD5: power-domain-cpu5 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD>; |
| domain-idle-states = <&BIG_CPU_SLEEP_0>; |
| }; |
| |
| CPU_PD6: power-domain-cpu6 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD>; |
| domain-idle-states = <&BIG_CPU_SLEEP_0>; |
| }; |
| |
| CPU_PD7: power-domain-cpu7 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD>; |
| domain-idle-states = <&BIG_CPU_SLEEP_0>; |
| }; |
| |
| CLUSTER_PD: power-domain-cluster { |
| #power-domain-cells = <0>; |
| domain-idle-states = <&CLUSTER_SLEEP_0>; |
| }; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| hyp_mem: hyp-mem@85700000 { |
| reg = <0 0x85700000 0 0x600000>; |
| no-map; |
| }; |
| |
| xbl_mem: xbl-mem@85e00000 { |
| reg = <0 0x85e00000 0 0x100000>; |
| no-map; |
| }; |
| |
| aop_mem: aop-mem@85fc0000 { |
| reg = <0 0x85fc0000 0 0x20000>; |
| no-map; |
| }; |
| |
| aop_cmd_db_mem: aop-cmd-db-mem@85fe0000 { |
| compatible = "qcom,cmd-db"; |
| reg = <0x0 0x85fe0000 0 0x20000>; |
| no-map; |
| }; |
| |
| smem@86000000 { |
| compatible = "qcom,smem"; |
| reg = <0x0 0x86000000 0 0x200000>; |
| no-map; |
| hwlocks = <&tcsr_mutex 3>; |
| }; |
| |
| tz_mem: tz@86200000 { |
| reg = <0 0x86200000 0 0x2d00000>; |
| no-map; |
| }; |
| |
| rmtfs_mem: rmtfs@88f00000 { |
| compatible = "qcom,rmtfs-mem"; |
| reg = <0 0x88f00000 0 0x200000>; |
| no-map; |
| |
| qcom,client-id = <1>; |
| qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>; |
| }; |
| |
| qseecom_mem: qseecom@8ab00000 { |
| reg = <0 0x8ab00000 0 0x1400000>; |
| no-map; |
| }; |
| |
| camera_mem: camera-mem@8bf00000 { |
| reg = <0 0x8bf00000 0 0x500000>; |
| no-map; |
| }; |
| |
| ipa_fw_mem: ipa-fw@8c400000 { |
| reg = <0 0x8c400000 0 0x10000>; |
| no-map; |
| }; |
| |
| ipa_gsi_mem: ipa-gsi@8c410000 { |
| reg = <0 0x8c410000 0 0x5000>; |
| no-map; |
| }; |
| |
| gpu_mem: gpu@8c415000 { |
| reg = <0 0x8c415000 0 0x2000>; |
| no-map; |
| }; |
| |
| adsp_mem: adsp@8c500000 { |
| reg = <0 0x8c500000 0 0x1a00000>; |
| no-map; |
| }; |
| |
| wlan_msa_mem: wlan-msa@8df00000 { |
| reg = <0 0x8df00000 0 0x100000>; |
| no-map; |
| }; |
| |
| mpss_region: mpss@8e000000 { |
| reg = <0 0x8e000000 0 0x7800000>; |
| no-map; |
| }; |
| |
| venus_mem: venus@95800000 { |
| reg = <0 0x95800000 0 0x500000>; |
| no-map; |
| }; |
| |
| cdsp_mem: cdsp@95d00000 { |
| reg = <0 0x95d00000 0 0x800000>; |
| no-map; |
| }; |
| |
| mba_region: mba@96500000 { |
| reg = <0 0x96500000 0 0x200000>; |
| no-map; |
| }; |
| |
| slpi_mem: slpi@96700000 { |
| reg = <0 0x96700000 0 0x1400000>; |
| no-map; |
| }; |
| |
| spss_mem: spss@97b00000 { |
| reg = <0 0x97b00000 0 0x100000>; |
| no-map; |
| }; |
| |
| mdata_mem: mpss-metadata { |
| alloc-ranges = <0 0xa0000000 0 0x20000000>; |
| size = <0 0x4000>; |
| no-map; |
| }; |
| |
| fastrpc_mem: fastrpc { |
| compatible = "shared-dma-pool"; |
| alloc-ranges = <0x0 0x00000000 0x0 0xffffffff>; |
| alignment = <0x0 0x400000>; |
| size = <0x0 0x1000000>; |
| reusable; |
| }; |
| }; |
| |
| adsp_pas: remoteproc-adsp { |
| compatible = "qcom,sdm845-adsp-pas"; |
| |
| interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| memory-region = <&adsp_mem>; |
| |
| qcom,qmp = <&aoss_qmp>; |
| |
| qcom,smem-states = <&adsp_smp2p_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>; |
| label = "lpass"; |
| qcom,remote-pid = <2>; |
| mboxes = <&apss_shared 8>; |
| |
| apr { |
| compatible = "qcom,apr-v2"; |
| qcom,glink-channels = "apr_audio_svc"; |
| qcom,domain = <APR_DOMAIN_ADSP>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| qcom,intents = <512 20>; |
| |
| service@3 { |
| reg = <APR_SVC_ADSP_CORE>; |
| compatible = "qcom,q6core"; |
| qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; |
| }; |
| |
| q6afe: service@4 { |
| compatible = "qcom,q6afe"; |
| reg = <APR_SVC_AFE>; |
| qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; |
| q6afedai: dais { |
| compatible = "qcom,q6afe-dais"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #sound-dai-cells = <1>; |
| }; |
| }; |
| |
| q6asm: service@7 { |
| compatible = "qcom,q6asm"; |
| reg = <APR_SVC_ASM>; |
| qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; |
| q6asmdai: dais { |
| compatible = "qcom,q6asm-dais"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #sound-dai-cells = <1>; |
| iommus = <&apps_smmu 0x1821 0x0>; |
| }; |
| }; |
| |
| q6adm: service@8 { |
| compatible = "qcom,q6adm"; |
| reg = <APR_SVC_ADM>; |
| qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; |
| q6routing: routing { |
| compatible = "qcom,q6adm-routing"; |
| #sound-dai-cells = <0>; |
| }; |
| }; |
| }; |
| |
| fastrpc { |
| compatible = "qcom,fastrpc"; |
| qcom,glink-channels = "fastrpcglink-apps-dsp"; |
| label = "adsp"; |
| qcom,non-secure-domain; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| compute-cb@3 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <3>; |
| iommus = <&apps_smmu 0x1823 0x0>; |
| }; |
| |
| compute-cb@4 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <4>; |
| iommus = <&apps_smmu 0x1824 0x0>; |
| }; |
| }; |
| }; |
| }; |
| |
| cdsp_pas: remoteproc-cdsp { |
| compatible = "qcom,sdm845-cdsp-pas"; |
| |
| interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>, |
| <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| memory-region = <&cdsp_mem>; |
| |
| qcom,qmp = <&aoss_qmp>; |
| |
| qcom,smem-states = <&cdsp_smp2p_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts = <GIC_SPI 574 IRQ_TYPE_EDGE_RISING>; |
| label = "turing"; |
| qcom,remote-pid = <5>; |
| mboxes = <&apss_shared 4>; |
| fastrpc { |
| compatible = "qcom,fastrpc"; |
| qcom,glink-channels = "fastrpcglink-apps-dsp"; |
| label = "cdsp"; |
| qcom,non-secure-domain; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| compute-cb@1 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <1>; |
| iommus = <&apps_smmu 0x1401 0x30>; |
| }; |
| |
| compute-cb@2 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <2>; |
| iommus = <&apps_smmu 0x1402 0x30>; |
| }; |
| |
| compute-cb@3 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <3>; |
| iommus = <&apps_smmu 0x1403 0x30>; |
| }; |
| |
| compute-cb@4 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <4>; |
| iommus = <&apps_smmu 0x1404 0x30>; |
| }; |
| |
| compute-cb@5 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <5>; |
| iommus = <&apps_smmu 0x1405 0x30>; |
| }; |
| |
| compute-cb@6 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <6>; |
| iommus = <&apps_smmu 0x1406 0x30>; |
| }; |
| |
| compute-cb@7 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <7>; |
| iommus = <&apps_smmu 0x1407 0x30>; |
| }; |
| |
| compute-cb@8 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <8>; |
| iommus = <&apps_smmu 0x1408 0x30>; |
| }; |
| }; |
| }; |
| }; |
| |
| smp2p-cdsp { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <94>, <432>; |
| |
| interrupts = <GIC_SPI 576 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apss_shared 6>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <5>; |
| |
| cdsp_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| cdsp_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-lpass { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <443>, <429>; |
| |
| interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apss_shared 10>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <2>; |
| |
| adsp_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| adsp_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-mpss { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <435>, <428>; |
| interrupts = <GIC_SPI 451 IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&apss_shared 14>; |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <1>; |
| |
| modem_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| modem_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| ipa_smp2p_out: ipa-ap-to-modem { |
| qcom,entry-name = "ipa"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| ipa_smp2p_in: ipa-modem-to-ap { |
| qcom,entry-name = "ipa"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-slpi { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <481>, <430>; |
| interrupts = <GIC_SPI 172 IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&apss_shared 26>; |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <3>; |
| |
| slpi_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| slpi_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| soc: soc@0 { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0 0 0 0 0x10 0>; |
| dma-ranges = <0 0 0 0 0x10 0>; |
| compatible = "simple-bus"; |
| |
| gcc: clock-controller@100000 { |
| compatible = "qcom,gcc-sdm845"; |
| reg = <0 0x00100000 0 0x1f0000>; |
| clocks = <&rpmhcc RPMH_CXO_CLK>, |
| <&rpmhcc RPMH_CXO_CLK_A>, |
| <&sleep_clk>, |
| <&pcie0_phy>, |
| <&pcie1_phy>; |
| clock-names = "bi_tcxo", |
| "bi_tcxo_ao", |
| "sleep_clk", |
| "pcie_0_pipe_clk", |
| "pcie_1_pipe_clk"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| }; |
| |
| qfprom@784000 { |
| compatible = "qcom,sdm845-qfprom", "qcom,qfprom"; |
| reg = <0 0x00784000 0 0x8ff>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| qusb2p_hstx_trim: hstx-trim-primary@1eb { |
| reg = <0x1eb 0x1>; |
| bits = <1 4>; |
| }; |
| |
| qusb2s_hstx_trim: hstx-trim-secondary@1eb { |
| reg = <0x1eb 0x2>; |
| bits = <6 4>; |
| }; |
| }; |
| |
| rng: rng@793000 { |
| compatible = "qcom,prng-ee"; |
| reg = <0 0x00793000 0 0x1000>; |
| clocks = <&gcc GCC_PRNG_AHB_CLK>; |
| clock-names = "core"; |
| }; |
| |
| gpi_dma0: dma-controller@800000 { |
| #dma-cells = <3>; |
| compatible = "qcom,sdm845-gpi-dma"; |
| reg = <0 0x00800000 0 0x60000>; |
| interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>; |
| dma-channels = <13>; |
| dma-channel-mask = <0xfa>; |
| iommus = <&apps_smmu 0x0016 0x0>; |
| status = "disabled"; |
| }; |
| |
| qupv3_id_0: geniqup@8c0000 { |
| compatible = "qcom,geni-se-qup"; |
| reg = <0 0x008c0000 0 0x6000>; |
| clock-names = "m-ahb", "s-ahb"; |
| clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, |
| <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; |
| iommus = <&apps_smmu 0x3 0x0>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core"; |
| status = "disabled"; |
| |
| i2c0: i2c@880000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00880000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c0_default>; |
| interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>, |
| <&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 0 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi0: spi@880000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00880000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi0_default>; |
| interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 0 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart0: serial@880000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00880000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart0_default>; |
| interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@884000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00884000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c1_default>; |
| interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>, |
| <&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 1 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi1: spi@884000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00884000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi1_default>; |
| interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 1 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@884000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00884000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart1_default>; |
| interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@888000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00888000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c2_default>; |
| interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>, |
| <&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 2 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi2: spi@888000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00888000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi2_default>; |
| interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 2 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@888000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00888000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart2_default>; |
| interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@88c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x0088c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c3_default>; |
| interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>, |
| <&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 3 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi3: spi@88c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x0088c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi3_default>; |
| interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 3 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@88c000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x0088c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart3_default>; |
| interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@890000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00890000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c4_default>; |
| interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>, |
| <&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 4 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi4: spi@890000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00890000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi4_default>; |
| interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 4 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@890000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00890000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart4_default>; |
| interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c@894000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00894000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c5_default>; |
| interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>, |
| <&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 5 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi5: spi@894000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00894000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi5_default>; |
| interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 5 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@894000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00894000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart5_default>; |
| interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c6: i2c@898000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00898000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c6_default>; |
| interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>, |
| <&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 6 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi6: spi@898000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00898000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi6_default>; |
| interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 6 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart6: serial@898000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00898000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart6_default>; |
| interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c7: i2c@89c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x0089c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c7_default>; |
| interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| spi7: spi@89c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x0089c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi7_default>; |
| interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 7 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart7: serial@89c000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x0089c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart7_default>; |
| interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| }; |
| |
| gpi_dma1: dma-controller@a00000 { |
| #dma-cells = <3>; |
| compatible = "qcom,sdm845-gpi-dma"; |
| reg = <0 0x00a00000 0 0x60000>; |
| interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>; |
| dma-channels = <13>; |
| dma-channel-mask = <0xfa>; |
| iommus = <&apps_smmu 0x06d6 0x0>; |
| status = "disabled"; |
| }; |
| |
| qupv3_id_1: geniqup@ac0000 { |
| compatible = "qcom,geni-se-qup"; |
| reg = <0 0x00ac0000 0 0x6000>; |
| clock-names = "m-ahb", "s-ahb"; |
| clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>, |
| <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>; |
| iommus = <&apps_smmu 0x6c3 0x0>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core"; |
| status = "disabled"; |
| |
| i2c8: i2c@a80000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a80000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c8_default>; |
| interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>, |
| <&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 0 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi8: spi@a80000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a80000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi8_default>; |
| interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 0 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart8: serial@a80000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00a80000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart8_default>; |
| interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c9: i2c@a84000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a84000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c9_default>; |
| interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>, |
| <&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 1 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi9: spi@a84000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a84000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi9_default>; |
| interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 1 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart9: serial@a84000 { |
| compatible = "qcom,geni-debug-uart"; |
| reg = <0 0x00a84000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart9_default>; |
| interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c10: i2c@a88000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a88000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c10_default>; |
| interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>, |
| <&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 2 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi10: spi@a88000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a88000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi10_default>; |
| interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 2 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart10: serial@a88000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00a88000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart10_default>; |
| interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c11: i2c@a8c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a8c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c11_default>; |
| interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>, |
| <&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 3 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi11: spi@a8c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a8c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi11_default>; |
| interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 3 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart11: serial@a8c000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00a8c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart11_default>; |
| interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c12: i2c@a90000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a90000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c12_default>; |
| interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>, |
| <&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 4 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi12: spi@a90000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a90000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi12_default>; |
| interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 4 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart12: serial@a90000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00a90000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart12_default>; |
| interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c13: i2c@a94000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a94000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c13_default>; |
| interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>, |
| <&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 5 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi13: spi@a94000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a94000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi13_default>; |
| interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 5 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart13: serial@a94000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00a94000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart13_default>; |
| interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c14: i2c@a98000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a98000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c14_default>; |
| interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>, |
| <&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 6 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| spi14: spi@a98000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a98000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi14_default>; |
| interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 6 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart14: serial@a98000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00a98000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart14_default>; |
| interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| |
| i2c15: i2c@a9c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a9c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c15_default>; |
| interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>, |
| <&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "qup-core", "qup-config", "qup-memory"; |
| dmas = <&gpi_dma1 0 7 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 7 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| spi15: spi@a9c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a9c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi15_default>; |
| interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| dmas = <&gpi_dma1 0 7 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 7 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| uart15: serial@a9c000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00a9c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart15_default>; |
| interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>; |
| interconnect-names = "qup-core", "qup-config"; |
| status = "disabled"; |
| }; |
| }; |
| |
| llcc: system-cache-controller@1100000 { |
| compatible = "qcom,sdm845-llcc"; |
| reg = <0 0x01100000 0 0x45000>, <0 0x01180000 0 0x50000>, |
| <0 0x01200000 0 0x50000>, <0 0x01280000 0 0x50000>, |
| <0 0x01300000 0 0x50000>; |
| reg-names = "llcc0_base", "llcc1_base", "llcc2_base", |
| "llcc3_base", "llcc_broadcast_base"; |
| interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| dma@10a2000 { |
| compatible = "qcom,sdm845-dcc", "qcom,dcc"; |
| reg = <0x0 0x010a2000 0x0 0x1000>, |
| <0x0 0x010ae000 0x0 0x2000>; |
| }; |
| |
| pmu@114a000 { |
| compatible = "qcom,sdm845-llcc-bwmon"; |
| reg = <0 0x0114a000 0 0x1000>; |
| interrupts = <GIC_SPI 580 IRQ_TYPE_LEVEL_HIGH>; |
| interconnects = <&mem_noc MASTER_LLCC 3 &mem_noc SLAVE_EBI1 3>; |
| |
| operating-points-v2 = <&llcc_bwmon_opp_table>; |
| |
| llcc_bwmon_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| /* |
| * The interconnect path bandwidth taken from |
| * cpu4_opp_table bandwidth for gladiator_noc-mem_noc |
| * interconnect. This also matches the |
| * bandwidth table of qcom,llccbw (qcom,bw-tbl, |
| * bus width: 4 bytes) from msm-4.9 downstream |
| * kernel. |
| */ |
| opp-0 { |
| opp-peak-kBps = <800000>; |
| }; |
| opp-1 { |
| opp-peak-kBps = <1804000>; |
| }; |
| opp-2 { |
| opp-peak-kBps = <3072000>; |
| }; |
| opp-3 { |
| opp-peak-kBps = <5412000>; |
| }; |
| opp-4 { |
| opp-peak-kBps = <7216000>; |
| }; |
| }; |
| }; |
| |
| pmu@1436400 { |
| compatible = "qcom,sdm845-cpu-bwmon", "qcom,sdm845-bwmon"; |
| reg = <0 0x01436400 0 0x600>; |
| interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>; |
| interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_LLCC 3>; |
| |
| operating-points-v2 = <&cpu_bwmon_opp_table>; |
| |
| cpu_bwmon_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| /* |
| * The interconnect path bandwidth taken from |
| * cpu4_opp_table bandwidth for OSM L3 |
| * interconnect. This also matches the OSM L3 |
| * from bandwidth table of qcom,cpu4-l3lat-mon |
| * (qcom,core-dev-table, bus width: 16 bytes) |
| * from msm-4.9 downstream kernel. |
| */ |
| opp-0 { |
| opp-peak-kBps = <4800000>; |
| }; |
| opp-1 { |
| opp-peak-kBps = <9216000>; |
| }; |
| opp-2 { |
| opp-peak-kBps = <15052800>; |
| }; |
| opp-3 { |
| opp-peak-kBps = <20889600>; |
| }; |
| opp-4 { |
| opp-peak-kBps = <25497600>; |
| }; |
| }; |
| }; |
| |
| pcie0: pci@1c00000 { |
| compatible = "qcom,pcie-sdm845"; |
| reg = <0 0x01c00000 0 0x2000>, |
| <0 0x60000000 0 0xf1d>, |
| <0 0x60000f20 0 0xa8>, |
| <0 0x60100000 0 0x100000>, |
| <0 0x01c07000 0 0x1000>; |
| reg-names = "parf", "dbi", "elbi", "config", "mhi"; |
| device_type = "pci"; |
| linux,pci-domain = <0>; |
| bus-range = <0x00 0xff>; |
| num-lanes = <1>; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>, |
| <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0xd00000>; |
| |
| interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ |
| <0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ |
| <0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ |
| <0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ |
| |
| clocks = <&gcc GCC_PCIE_0_PIPE_CLK>, |
| <&gcc GCC_PCIE_0_AUX_CLK>, |
| <&gcc GCC_PCIE_0_CFG_AHB_CLK>, |
| <&gcc GCC_PCIE_0_MSTR_AXI_CLK>, |
| <&gcc GCC_PCIE_0_SLV_AXI_CLK>, |
| <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>, |
| <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>; |
| clock-names = "pipe", |
| "aux", |
| "cfg", |
| "bus_master", |
| "bus_slave", |
| "slave_q2a", |
| "tbu"; |
| |
| iommu-map = <0x0 &apps_smmu 0x1c10 0x1>, |
| <0x100 &apps_smmu 0x1c11 0x1>, |
| <0x200 &apps_smmu 0x1c12 0x1>, |
| <0x300 &apps_smmu 0x1c13 0x1>, |
| <0x400 &apps_smmu 0x1c14 0x1>, |
| <0x500 &apps_smmu 0x1c15 0x1>, |
| <0x600 &apps_smmu 0x1c16 0x1>, |
| <0x700 &apps_smmu 0x1c17 0x1>, |
| <0x800 &apps_smmu 0x1c18 0x1>, |
| <0x900 &apps_smmu 0x1c19 0x1>, |
| <0xa00 &apps_smmu 0x1c1a 0x1>, |
| <0xb00 &apps_smmu 0x1c1b 0x1>, |
| <0xc00 &apps_smmu 0x1c1c 0x1>, |
| <0xd00 &apps_smmu 0x1c1d 0x1>, |
| <0xe00 &apps_smmu 0x1c1e 0x1>, |
| <0xf00 &apps_smmu 0x1c1f 0x1>; |
| |
| resets = <&gcc GCC_PCIE_0_BCR>; |
| reset-names = "pci"; |
| |
| power-domains = <&gcc PCIE_0_GDSC>; |
| |
| phys = <&pcie0_phy>; |
| phy-names = "pciephy"; |
| |
| status = "disabled"; |
| }; |
| |
| pcie0_phy: phy@1c06000 { |
| compatible = "qcom,sdm845-qmp-pcie-phy"; |
| reg = <0 0x01c06000 0 0x1000>; |
| clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, |
| <&gcc GCC_PCIE_0_CFG_AHB_CLK>, |
| <&gcc GCC_PCIE_0_CLKREF_CLK>, |
| <&gcc GCC_PCIE_PHY_REFGEN_CLK>, |
| <&gcc GCC_PCIE_0_PIPE_CLK>; |
| clock-names = "aux", |
| "cfg_ahb", |
| "ref", |
| "refgen", |
| "pipe"; |
| |
| clock-output-names = "pcie_0_pipe_clk"; |
| #clock-cells = <0>; |
| |
| #phy-cells = <0>; |
| |
| resets = <&gcc GCC_PCIE_0_PHY_BCR>; |
| reset-names = "phy"; |
| |
| assigned-clocks = <&gcc GCC_PCIE_PHY_REFGEN_CLK>; |
| assigned-clock-rates = <100000000>; |
| |
| status = "disabled"; |
| }; |
| |
| pcie1: pci@1c08000 { |
| compatible = "qcom,pcie-sdm845"; |
| reg = <0 0x01c08000 0 0x2000>, |
| <0 0x40000000 0 0xf1d>, |
| <0 0x40000f20 0 0xa8>, |
| <0 0x40100000 0 0x100000>, |
| <0 0x01c0c000 0 0x1000>; |
| reg-names = "parf", "dbi", "elbi", "config", "mhi"; |
| device_type = "pci"; |
| linux,pci-domain = <1>; |
| bus-range = <0x00 0xff>; |
| num-lanes = <1>; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>, |
| <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>; |
| |
| interrupts = <GIC_SPI 307 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ |
| <0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ |
| <0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ |
| <0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ |
| |
| clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, |
| <&gcc GCC_PCIE_1_AUX_CLK>, |
| <&gcc GCC_PCIE_1_CFG_AHB_CLK>, |
| <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, |
| <&gcc GCC_PCIE_1_SLV_AXI_CLK>, |
| <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>, |
| <&gcc GCC_PCIE_1_CLKREF_CLK>, |
| <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>; |
| clock-names = "pipe", |
| "aux", |
| "cfg", |
| "bus_master", |
| "bus_slave", |
| "slave_q2a", |
| "ref", |
| "tbu"; |
| |
| assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>; |
| assigned-clock-rates = <19200000>; |
| |
| iommu-map = <0x0 &apps_smmu 0x1c00 0x1>, |
| <0x100 &apps_smmu 0x1c01 0x1>, |
| <0x200 &apps_smmu 0x1c02 0x1>, |
| <0x300 &apps_smmu 0x1c03 0x1>, |
| <0x400 &apps_smmu 0x1c04 0x1>, |
| <0x500 &apps_smmu 0x1c05 0x1>, |
| <0x600 &apps_smmu 0x1c06 0x1>, |
| <0x700 &apps_smmu 0x1c07 0x1>, |
| <0x800 &apps_smmu 0x1c08 0x1>, |
| <0x900 &apps_smmu 0x1c09 0x1>, |
| <0xa00 &apps_smmu 0x1c0a 0x1>, |
| <0xb00 &apps_smmu 0x1c0b 0x1>, |
| <0xc00 &apps_smmu 0x1c0c 0x1>, |
| <0xd00 &apps_smmu 0x1c0d 0x1>, |
| <0xe00 &apps_smmu 0x1c0e 0x1>, |
| <0xf00 &apps_smmu 0x1c0f 0x1>; |
| |
| resets = <&gcc GCC_PCIE_1_BCR>; |
| reset-names = "pci"; |
| |
| power-domains = <&gcc PCIE_1_GDSC>; |
| |
| phys = <&pcie1_phy>; |
| phy-names = "pciephy"; |
| |
| status = "disabled"; |
| }; |
| |
| pcie1_phy: phy@1c0a000 { |
| compatible = "qcom,sdm845-qhp-pcie-phy"; |
| reg = <0 0x01c0a000 0 0x2000>; |
| clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, |
| <&gcc GCC_PCIE_1_CFG_AHB_CLK>, |
| <&gcc GCC_PCIE_1_CLKREF_CLK>, |
| <&gcc GCC_PCIE_PHY_REFGEN_CLK>, |
| <&gcc GCC_PCIE_1_PIPE_CLK>; |
| clock-names = "aux", |
| "cfg_ahb", |
| "ref", |
| "refgen", |
| "pipe"; |
| |
| clock-output-names = "pcie_1_pipe_clk"; |
| #clock-cells = <0>; |
| |
| #phy-cells = <0>; |
| |
| resets = <&gcc GCC_PCIE_1_PHY_BCR>; |
| reset-names = "phy"; |
| |
| assigned-clocks = <&gcc GCC_PCIE_PHY_REFGEN_CLK>; |
| assigned-clock-rates = <100000000>; |
| |
| status = "disabled"; |
| }; |
| |
| mem_noc: interconnect@1380000 { |
| compatible = "qcom,sdm845-mem-noc"; |
| reg = <0 0x01380000 0 0x27200>; |
| #interconnect-cells = <2>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| dc_noc: interconnect@14e0000 { |
| compatible = "qcom,sdm845-dc-noc"; |
| reg = <0 0x014e0000 0 0x400>; |
| #interconnect-cells = <2>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| config_noc: interconnect@1500000 { |
| compatible = "qcom,sdm845-config-noc"; |
| reg = <0 0x01500000 0 0x5080>; |
| #interconnect-cells = <2>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| system_noc: interconnect@1620000 { |
| compatible = "qcom,sdm845-system-noc"; |
| reg = <0 0x01620000 0 0x18080>; |
| #interconnect-cells = <2>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| aggre1_noc: interconnect@16e0000 { |
| compatible = "qcom,sdm845-aggre1-noc"; |
| reg = <0 0x016e0000 0 0x15080>; |
| #interconnect-cells = <2>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| aggre2_noc: interconnect@1700000 { |
| compatible = "qcom,sdm845-aggre2-noc"; |
| reg = <0 0x01700000 0 0x1f300>; |
| #interconnect-cells = <2>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| mmss_noc: interconnect@1740000 { |
| compatible = "qcom,sdm845-mmss-noc"; |
| reg = <0 0x01740000 0 0x1c100>; |
| #interconnect-cells = <2>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| ufs_mem_hc: ufshc@1d84000 { |
| compatible = "qcom,sdm845-ufshc", "qcom,ufshc", |
| "jedec,ufs-2.0"; |
| reg = <0 0x01d84000 0 0x2500>, |
| <0 0x01d90000 0 0x8000>; |
| reg-names = "std", "ice"; |
| interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&ufs_mem_phy_lanes>; |
| phy-names = "ufsphy"; |
| lanes-per-direction = <2>; |
| power-domains = <&gcc UFS_PHY_GDSC>; |
| #reset-cells = <1>; |
| resets = <&gcc GCC_UFS_PHY_BCR>; |
| reset-names = "rst"; |
| |
| iommus = <&apps_smmu 0x100 0xf>; |
| |
| clock-names = |
| "core_clk", |
| "bus_aggr_clk", |
| "iface_clk", |
| "core_clk_unipro", |
| "ref_clk", |
| "tx_lane0_sync_clk", |
| "rx_lane0_sync_clk", |
| "rx_lane1_sync_clk", |
| "ice_core_clk"; |
| clocks = |
| <&gcc GCC_UFS_PHY_AXI_CLK>, |
| <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, |
| <&gcc GCC_UFS_PHY_AHB_CLK>, |
| <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, |
| <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, |
| <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>, |
| <&gcc GCC_UFS_PHY_ICE_CORE_CLK>; |
| freq-table-hz = |
| <50000000 200000000>, |
| <0 0>, |
| <0 0>, |
| <37500000 150000000>, |
| <0 0>, |
| <0 0>, |
| <0 0>, |
| <0 0>, |
| <75000000 300000000>; |
| |
| interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mem_noc SLAVE_EBI1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>; |
| interconnect-names = "ufs-ddr", "cpu-ufs"; |
| |
| status = "disabled"; |
| }; |
| |
| ufs_mem_phy: phy@1d87000 { |
| compatible = "qcom,sdm845-qmp-ufs-phy"; |
| reg = <0 0x01d87000 0 0x18c>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| clock-names = "ref", |
| "ref_aux"; |
| clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>, |
| <&gcc GCC_UFS_PHY_PHY_AUX_CLK>; |
| |
| resets = <&ufs_mem_hc 0>; |
| reset-names = "ufsphy"; |
| status = "disabled"; |
| |
| ufs_mem_phy_lanes: phy@1d87400 { |
| reg = <0 0x01d87400 0 0x108>, |
| <0 0x01d87600 0 0x1e0>, |
| <0 0x01d87c00 0 0x1dc>, |
| <0 0x01d87800 0 0x108>, |
| <0 0x01d87a00 0 0x1e0>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| cryptobam: dma-controller@1dc4000 { |
| compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0"; |
| reg = <0 0x01dc4000 0 0x24000>; |
| interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rpmhcc RPMH_CE_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| qcom,controlled-remotely; |
| iommus = <&apps_smmu 0x704 0x1>, |
| <&apps_smmu 0x706 0x1>, |
| <&apps_smmu 0x714 0x1>, |
| <&apps_smmu 0x716 0x1>; |
| }; |
| |
| crypto: crypto@1dfa000 { |
| compatible = "qcom,crypto-v5.4"; |
| reg = <0 0x01dfa000 0 0x6000>; |
| clocks = <&gcc GCC_CE1_AHB_CLK>, |
| <&gcc GCC_CE1_AXI_CLK>, |
| <&rpmhcc RPMH_CE_CLK>; |
| clock-names = "iface", "bus", "core"; |
| dmas = <&cryptobam 6>, <&cryptobam 7>; |
| dma-names = "rx", "tx"; |
| iommus = <&apps_smmu 0x704 0x1>, |
| <&apps_smmu 0x706 0x1>, |
| <&apps_smmu 0x714 0x1>, |
| <&apps_smmu 0x716 0x1>; |
| }; |
| |
| ipa: ipa@1e40000 { |
| compatible = "qcom,sdm845-ipa"; |
| |
| iommus = <&apps_smmu 0x720 0x0>, |
| <&apps_smmu 0x722 0x0>; |
| reg = <0 0x01e40000 0 0x7000>, |
| <0 0x01e47000 0 0x2000>, |
| <0 0x01e04000 0 0x2c000>; |
| reg-names = "ipa-reg", |
| "ipa-shared", |
| "gsi"; |
| |
| interrupts-extended = <&intc GIC_SPI 311 IRQ_TYPE_EDGE_RISING>, |
| <&intc GIC_SPI 432 IRQ_TYPE_LEVEL_HIGH>, |
| <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "ipa", |
| "gsi", |
| "ipa-clock-query", |
| "ipa-setup-ready"; |
| |
| clocks = <&rpmhcc RPMH_IPA_CLK>; |
| clock-names = "core"; |
| |
| interconnects = <&aggre2_noc MASTER_IPA 0 &mem_noc SLAVE_EBI1 0>, |
| <&aggre2_noc MASTER_IPA 0 &system_noc SLAVE_IMEM 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_IPA_CFG 0>; |
| interconnect-names = "memory", |
| "imem", |
| "config"; |
| |
| qcom,smem-states = <&ipa_smp2p_out 0>, |
| <&ipa_smp2p_out 1>; |
| qcom,smem-state-names = "ipa-clock-enabled-valid", |
| "ipa-clock-enabled"; |
| |
| status = "disabled"; |
| }; |
| |
| tcsr_mutex: hwlock@1f40000 { |
| compatible = "qcom,tcsr-mutex"; |
| reg = <0 0x01f40000 0 0x20000>; |
| #hwlock-cells = <1>; |
| }; |
| |
| tcsr_regs_1: syscon@1f60000 { |
| compatible = "qcom,sdm845-tcsr", "syscon"; |
| reg = <0 0x01f60000 0 0x20000>; |
| }; |
| |
| tlmm: pinctrl@3400000 { |
| compatible = "qcom,sdm845-pinctrl"; |
| reg = <0 0x03400000 0 0xc00000>; |
| interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&tlmm 0 0 151>; |
| wakeup-parent = <&pdc_intc>; |
| |
| cci0_default: cci0-default-state { |
| /* SDA, SCL */ |
| pins = "gpio17", "gpio18"; |
| function = "cci_i2c"; |
| |
| bias-pull-up; |
| drive-strength = <2>; /* 2 mA */ |
| }; |
| |
| cci0_sleep: cci0-sleep-state { |
| /* SDA, SCL */ |
| pins = "gpio17", "gpio18"; |
| function = "cci_i2c"; |
| |
| drive-strength = <2>; /* 2 mA */ |
| bias-pull-down; |
| }; |
| |
| cci1_default: cci1-default-state { |
| /* SDA, SCL */ |
| pins = "gpio19", "gpio20"; |
| function = "cci_i2c"; |
| |
| bias-pull-up; |
| drive-strength = <2>; /* 2 mA */ |
| }; |
| |
| cci1_sleep: cci1-sleep-state { |
| /* SDA, SCL */ |
| pins = "gpio19", "gpio20"; |
| function = "cci_i2c"; |
| |
| drive-strength = <2>; /* 2 mA */ |
| bias-pull-down; |
| }; |
| |
| qspi_clk: qspi-clk-state { |
| pins = "gpio95"; |
| function = "qspi_clk"; |
| }; |
| |
| qspi_cs0: qspi-cs0-state { |
| pins = "gpio90"; |
| function = "qspi_cs"; |
| }; |
| |
| qspi_cs1: qspi-cs1-state { |
| pins = "gpio89"; |
| function = "qspi_cs"; |
| }; |
| |
| qspi_data0: qspi-data0-state { |
| pins = "gpio91"; |
| function = "qspi_data"; |
| }; |
| |
| qspi_data1: qspi-data1-state { |
| pins = "gpio92"; |
| function = "qspi_data"; |
| }; |
| |
| qspi_data23: qspi-data23-state { |
| pins = "gpio93", "gpio94"; |
| function = "qspi_data"; |
| }; |
| |
| qup_i2c0_default: qup-i2c0-default-state { |
| pins = "gpio0", "gpio1"; |
| function = "qup0"; |
| }; |
| |
| qup_i2c1_default: qup-i2c1-default-state { |
| pins = "gpio17", "gpio18"; |
| function = "qup1"; |
| }; |
| |
| qup_i2c2_default: qup-i2c2-default-state { |
| pins = "gpio27", "gpio28"; |
| function = "qup2"; |
| }; |
| |
| qup_i2c3_default: qup-i2c3-default-state { |
| pins = "gpio41", "gpio42"; |
| function = "qup3"; |
| }; |
| |
| qup_i2c4_default: qup-i2c4-default-state { |
| pins = "gpio89", "gpio90"; |
| function = "qup4"; |
| }; |
| |
| qup_i2c5_default: qup-i2c5-default-state { |
| pins = "gpio85", "gpio86"; |
| function = "qup5"; |
| }; |
| |
| qup_i2c6_default: qup-i2c6-default-state { |
| pins = "gpio45", "gpio46"; |
| function = "qup6"; |
| }; |
| |
| qup_i2c7_default: qup-i2c7-default-state { |
| pins = "gpio93", "gpio94"; |
| function = "qup7"; |
| }; |
| |
| qup_i2c8_default: qup-i2c8-default-state { |
| pins = "gpio65", "gpio66"; |
| function = "qup8"; |
| }; |
| |
| qup_i2c9_default: qup-i2c9-default-state { |
| pins = "gpio6", "gpio7"; |
| function = "qup9"; |
| }; |
| |
| qup_i2c10_default: qup-i2c10-default-state { |
| pins = "gpio55", "gpio56"; |
| function = "qup10"; |
| }; |
| |
| qup_i2c11_default: qup-i2c11-default-state { |
| pins = "gpio31", "gpio32"; |
| function = "qup11"; |
| }; |
| |
| qup_i2c12_default: qup-i2c12-default-state { |
| pins = "gpio49", "gpio50"; |
| function = "qup12"; |
| }; |
| |
| qup_i2c13_default: qup-i2c13-default-state { |
| pins = "gpio105", "gpio106"; |
| function = "qup13"; |
| }; |
| |
| qup_i2c14_default: qup-i2c14-default-state { |
| pins = "gpio33", "gpio34"; |
| function = "qup14"; |
| }; |
| |
| qup_i2c15_default: qup-i2c15-default-state { |
| pins = "gpio81", "gpio82"; |
| function = "qup15"; |
| }; |
| |
| qup_spi0_default: qup-spi0-default-state { |
| pins = "gpio0", "gpio1", "gpio2", "gpio3"; |
| function = "qup0"; |
| }; |
| |
| qup_spi1_default: qup-spi1-default-state { |
| pins = "gpio17", "gpio18", "gpio19", "gpio20"; |
| function = "qup1"; |
| }; |
| |
| qup_spi2_default: qup-spi2-default-state { |
| pins = "gpio27", "gpio28", "gpio29", "gpio30"; |
| function = "qup2"; |
| }; |
| |
| qup_spi3_default: qup-spi3-default-state { |
| pins = "gpio41", "gpio42", "gpio43", "gpio44"; |
| function = "qup3"; |
| }; |
| |
| qup_spi4_default: qup-spi4-default-state { |
| pins = "gpio89", "gpio90", "gpio91", "gpio92"; |
| function = "qup4"; |
| }; |
| |
| qup_spi5_default: qup-spi5-default-state { |
| pins = "gpio85", "gpio86", "gpio87", "gpio88"; |
| function = "qup5"; |
| }; |
| |
| qup_spi6_default: qup-spi6-default-state { |
| pins = "gpio45", "gpio46", "gpio47", "gpio48"; |
| function = "qup6"; |
| }; |
| |
| qup_spi7_default: qup-spi7-default-state { |
| pins = "gpio93", "gpio94", "gpio95", "gpio96"; |
| function = "qup7"; |
| }; |
| |
| qup_spi8_default: qup-spi8-default-state { |
| pins = "gpio65", "gpio66", "gpio67", "gpio68"; |
| function = "qup8"; |
| }; |
| |
| qup_spi9_default: qup-spi9-default-state { |
| pins = "gpio6", "gpio7", "gpio4", "gpio5"; |
| function = "qup9"; |
| }; |
| |
| qup_spi10_default: qup-spi10-default-state { |
| pins = "gpio55", "gpio56", "gpio53", "gpio54"; |
| function = "qup10"; |
| }; |
| |
| qup_spi11_default: qup-spi11-default-state { |
| pins = "gpio31", "gpio32", "gpio33", "gpio34"; |
| function = "qup11"; |
| }; |
| |
| qup_spi12_default: qup-spi12-default-state { |
| pins = "gpio49", "gpio50", "gpio51", "gpio52"; |
| function = "qup12"; |
| }; |
| |
| qup_spi13_default: qup-spi13-default-state { |
| pins = "gpio105", "gpio106", "gpio107", "gpio108"; |
| function = "qup13"; |
| }; |
| |
| qup_spi14_default: qup-spi14-default-state { |
| pins = "gpio33", "gpio34", "gpio31", "gpio32"; |
| function = "qup14"; |
| }; |
| |
| qup_spi15_default: qup-spi15-default-state { |
| pins = "gpio81", "gpio82", "gpio83", "gpio84"; |
| function = "qup15"; |
| }; |
| |
| qup_uart0_default: qup-uart0-default-state { |
| qup_uart0_tx: tx-pins { |
| pins = "gpio2"; |
| function = "qup0"; |
| }; |
| |
| qup_uart0_rx: rx-pins { |
| pins = "gpio3"; |
| function = "qup0"; |
| }; |
| }; |
| |
| qup_uart1_default: qup-uart1-default-state { |
| qup_uart1_tx: tx-pins { |
| pins = "gpio19"; |
| function = "qup1"; |
| }; |
| |
| qup_uart1_rx: rx-pins { |
| pins = "gpio20"; |
| function = "qup1"; |
| }; |
| }; |
| |
| qup_uart2_default: qup-uart2-default-state { |
| qup_uart2_tx: tx-pins { |
| pins = "gpio29"; |
| function = "qup2"; |
| }; |
| |
| qup_uart2_rx: rx-pins { |
| pins = "gpio30"; |
| function = "qup2"; |
| }; |
| }; |
| |
| qup_uart3_default: qup-uart3-default-state { |
| qup_uart3_tx: tx-pins { |
| pins = "gpio43"; |
| function = "qup3"; |
| }; |
| |
| qup_uart3_rx: rx-pins { |
| pins = "gpio44"; |
| function = "qup3"; |
| }; |
| }; |
| |
| qup_uart3_4pin: qup-uart3-4pin-state { |
| qup_uart3_4pin_cts: cts-pins { |
| pins = "gpio41"; |
| function = "qup3"; |
| }; |
| |
| qup_uart3_4pin_rts_tx: rts-tx-pins { |
| pins = "gpio42", "gpio43"; |
| function = "qup3"; |
| }; |
| |
| qup_uart3_4pin_rx: rx-pins { |
| pins = "gpio44"; |
| function = "qup3"; |
| }; |
| }; |
| |
| qup_uart4_default: qup-uart4-default-state { |
| qup_uart4_tx: tx-pins { |
| pins = "gpio91"; |
| function = "qup4"; |
| }; |
| |
| qup_uart4_rx: rx-pins { |
| pins = "gpio92"; |
| function = "qup4"; |
| }; |
| }; |
| |
| qup_uart5_default: qup-uart5-default-state { |
| qup_uart5_tx: tx-pins { |
| pins = "gpio87"; |
| function = "qup5"; |
| }; |
| |
| qup_uart5_rx: rx-pins { |
| pins = "gpio88"; |
| function = "qup5"; |
| }; |
| }; |
| |
| qup_uart6_default: qup-uart6-default-state { |
| qup_uart6_tx: tx-pins { |
| pins = "gpio47"; |
| function = "qup6"; |
| }; |
| |
| qup_uart6_rx: rx-pins { |
| pins = "gpio48"; |
| function = "qup6"; |
| }; |
| }; |
| |
| qup_uart6_4pin: qup-uart6-4pin-state { |
| qup_uart6_4pin_cts: cts-pins { |
| pins = "gpio45"; |
| function = "qup6"; |
| bias-pull-down; |
| }; |
| |
| qup_uart6_4pin_rts_tx: rts-tx-pins { |
| pins = "gpio46", "gpio47"; |
| function = "qup6"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| qup_uart6_4pin_rx: rx-pins { |
| pins = "gpio48"; |
| function = "qup6"; |
| bias-pull-up; |
| }; |
| }; |
| |
| qup_uart7_default: qup-uart7-default-state { |
| qup_uart7_tx: tx-pins { |
| pins = "gpio95"; |
| function = "qup7"; |
| }; |
| |
| qup_uart7_rx: rx-pins { |
| pins = "gpio96"; |
| function = "qup7"; |
| }; |
| }; |
| |
| qup_uart8_default: qup-uart8-default-state { |
| qup_uart8_tx: tx-pins { |
| pins = "gpio67"; |
| function = "qup8"; |
| }; |
| |
| qup_uart8_rx: rx-pins { |
| pins = "gpio68"; |
| function = "qup8"; |
| }; |
| }; |
| |
| qup_uart9_default: qup-uart9-default-state { |
| qup_uart9_tx: tx-pins { |
| pins = "gpio4"; |
| function = "qup9"; |
| }; |
| |
| qup_uart9_rx: rx-pins { |
| pins = "gpio5"; |
| function = "qup9"; |
| }; |
| }; |
| |
| qup_uart10_default: qup-uart10-default-state { |
| qup_uart10_tx: tx-pins { |
| pins = "gpio53"; |
| function = "qup10"; |
| }; |
| |
| qup_uart10_rx: rx-pins { |
| pins = "gpio54"; |
| function = "qup10"; |
| }; |
| }; |
| |
| qup_uart11_default: qup-uart11-default-state { |
| qup_uart11_tx: tx-pins { |
| pins = "gpio33"; |
| function = "qup11"; |
| }; |
| |
| qup_uart11_rx: rx-pins { |
| pins = "gpio34"; |
| function = "qup11"; |
| }; |
| }; |
| |
| qup_uart12_default: qup-uart12-default-state { |
| qup_uart12_tx: tx-pins { |
| pins = "gpio51"; |
| function = "qup0"; |
| }; |
| |
| qup_uart12_rx: rx-pins { |
| pins = "gpio52"; |
| function = "qup0"; |
| }; |
| }; |
| |
| qup_uart13_default: qup-uart13-default-state { |
| qup_uart13_tx: tx-pins { |
| pins = "gpio107"; |
| function = "qup13"; |
| }; |
| |
| qup_uart13_rx: rx-pins { |
| pins = "gpio108"; |
| function = "qup13"; |
| }; |
| }; |
| |
| qup_uart14_default: qup-uart14-default-state { |
| qup_uart14_tx: tx-pins { |
| pins = "gpio31"; |
| function = "qup14"; |
| }; |
| |
| qup_uart14_rx: rx-pins { |
| pins = "gpio32"; |
| function = "qup14"; |
| }; |
| }; |
| |
| qup_uart15_default: qup-uart15-default-state { |
| qup_uart15_tx: tx-pins { |
| pins = "gpio83"; |
| function = "qup15"; |
| }; |
| |
| qup_uart15_rx: rx-pins { |
| pins = "gpio84"; |
| function = "qup15"; |
| }; |
| }; |
| |
| quat_mi2s_sleep: quat-mi2s-sleep-state { |
| pins = "gpio58", "gpio59"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| quat_mi2s_active: quat-mi2s-active-state { |
| pins = "gpio58", "gpio59"; |
| function = "qua_mi2s"; |
| drive-strength = <8>; |
| bias-disable; |
| output-high; |
| }; |
| |
| quat_mi2s_sd0_sleep: quat-mi2s-sd0-sleep-state { |
| pins = "gpio60"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| quat_mi2s_sd0_active: quat-mi2s-sd0-active-state { |
| pins = "gpio60"; |
| function = "qua_mi2s"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| quat_mi2s_sd1_sleep: quat-mi2s-sd1-sleep-state { |
| pins = "gpio61"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| quat_mi2s_sd1_active: quat-mi2s-sd1-active-state { |
| pins = "gpio61"; |
| function = "qua_mi2s"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| quat_mi2s_sd2_sleep: quat-mi2s-sd2-sleep-state { |
| pins = "gpio62"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| quat_mi2s_sd2_active: quat-mi2s-sd2-active-state { |
| pins = "gpio62"; |
| function = "qua_mi2s"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| quat_mi2s_sd3_sleep: quat-mi2s-sd3-sleep-state { |
| pins = "gpio63"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| quat_mi2s_sd3_active: quat-mi2s-sd3-active-state { |
| pins = "gpio63"; |
| function = "qua_mi2s"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| }; |
| |
| mss_pil: remoteproc@4080000 { |
| compatible = "qcom,sdm845-mss-pil"; |
| reg = <0 0x04080000 0 0x408>, <0 0x04180000 0 0x48>; |
| reg-names = "qdsp6", "rmb"; |
| |
| interrupts-extended = |
| <&intc GIC_SPI 266 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack", |
| "shutdown-ack"; |
| |
| clocks = <&gcc GCC_MSS_CFG_AHB_CLK>, |
| <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>, |
| <&gcc GCC_BOOT_ROM_AHB_CLK>, |
| <&gcc GCC_MSS_GPLL0_DIV_CLK_SRC>, |
| <&gcc GCC_MSS_SNOC_AXI_CLK>, |
| <&gcc GCC_MSS_MFAB_AXIS_CLK>, |
| <&gcc GCC_PRNG_AHB_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "iface", "bus", "mem", "gpll0_mss", |
| "snoc_axi", "mnoc_axi", "prng", "xo"; |
| |
| qcom,qmp = <&aoss_qmp>; |
| |
| qcom,smem-states = <&modem_smp2p_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| resets = <&aoss_reset AOSS_CC_MSS_RESTART>, |
| <&pdc_reset PDC_MODEM_SYNC_RESET>; |
| reset-names = "mss_restart", "pdc_reset"; |
| |
| qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>; |
| |
| power-domains = <&rpmhpd SDM845_CX>, |
| <&rpmhpd SDM845_MX>, |
| <&rpmhpd SDM845_MSS>; |
| power-domain-names = "cx", "mx", "mss"; |
| |
| status = "disabled"; |
| |
| mba { |
| memory-region = <&mba_region>; |
| }; |
| |
| mpss { |
| memory-region = <&mpss_region>; |
| }; |
| |
| metadata { |
| memory-region = <&mdata_mem>; |
| }; |
| |
| glink-edge { |
| interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>; |
| label = "modem"; |
| qcom,remote-pid = <1>; |
| mboxes = <&apss_shared 12>; |
| }; |
| }; |
| |
| gpucc: clock-controller@5090000 { |
| compatible = "qcom,sdm845-gpucc"; |
| reg = <0 0x05090000 0 0x9000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| clocks = <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_GPU_GPLL0_CLK_SRC>, |
| <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>; |
| clock-names = "bi_tcxo", |
| "gcc_gpu_gpll0_clk_src", |
| "gcc_gpu_gpll0_div_clk_src"; |
| }; |
| |
| slpi_pas: remoteproc@5c00000 { |
| compatible = "qcom,sdm845-slpi-pas"; |
| reg = <0 0x5c00000 0 0x4000>; |
| |
| interrupts-extended = <&intc GIC_SPI 494 IRQ_TYPE_EDGE_RISING>, |
| <&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| qcom,qmp = <&aoss_qmp>; |
| |
| power-domains = <&rpmhpd SDM845_CX>, |
| <&rpmhpd SDM845_MX>; |
| power-domain-names = "lcx", "lmx"; |
| |
| memory-region = <&slpi_mem>; |
| |
| qcom,smem-states = <&slpi_smp2p_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts = <GIC_SPI 170 IRQ_TYPE_EDGE_RISING>; |
| label = "dsps"; |
| qcom,remote-pid = <3>; |
| mboxes = <&apss_shared 24>; |
| |
| fastrpc { |
| compatible = "qcom,fastrpc"; |
| qcom,glink-channels = "fastrpcglink-apps-dsp"; |
| label = "sdsp"; |
| qcom,non-secure-domain; |
| qcom,vmids = <QCOM_SCM_VMID_HLOS QCOM_SCM_VMID_MSS_MSA |
| QCOM_SCM_VMID_SSC_Q6 QCOM_SCM_VMID_ADSP_Q6>; |
| memory-region = <&fastrpc_mem>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| compute-cb@0 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <0>; |
| }; |
| }; |
| }; |
| }; |
| |
| stm@6002000 { |
| compatible = "arm,coresight-stm", "arm,primecell"; |
| reg = <0 0x06002000 0 0x1000>, |
| <0 0x16280000 0 0x180000>; |
| reg-names = "stm-base", "stm-stimulus-base"; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| stm_out: endpoint { |
| remote-endpoint = |
| <&funnel0_in7>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@6041000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0 0x06041000 0 0x1000>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| funnel0_out: endpoint { |
| remote-endpoint = |
| <&merge_funnel_in0>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@7 { |
| reg = <7>; |
| funnel0_in7: endpoint { |
| remote-endpoint = <&stm_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@6043000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0 0x06043000 0 0x1000>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| funnel2_out: endpoint { |
| remote-endpoint = |
| <&merge_funnel_in2>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@5 { |
| reg = <5>; |
| funnel2_in5: endpoint { |
| remote-endpoint = |
| <&apss_merge_funnel_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@6045000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0 0x06045000 0 0x1000>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| merge_funnel_out: endpoint { |
| remote-endpoint = <&etf_in>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| merge_funnel_in0: endpoint { |
| remote-endpoint = |
| <&funnel0_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| merge_funnel_in2: endpoint { |
| remote-endpoint = |
| <&funnel2_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| replicator@6046000 { |
| compatible = "arm,coresight-dynamic-replicator", "arm,primecell"; |
| reg = <0 0x06046000 0 0x1000>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| replicator_out: endpoint { |
| remote-endpoint = <&etr_in>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| port { |
| replicator_in: endpoint { |
| remote-endpoint = <&etf_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| etf@6047000 { |
| compatible = "arm,coresight-tmc", "arm,primecell"; |
| reg = <0 0x06047000 0 0x1000>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| etf_out: endpoint { |
| remote-endpoint = |
| <&replicator_in>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <1>; |
| etf_in: endpoint { |
| remote-endpoint = |
| <&merge_funnel_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| etr@6048000 { |
| compatible = "arm,coresight-tmc", "arm,primecell"; |
| reg = <0 0x06048000 0 0x1000>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| arm,scatter-gather; |
| |
| in-ports { |
| port { |
| etr_in: endpoint { |
| remote-endpoint = |
| <&replicator_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@7040000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0 0x07040000 0 0x1000>; |
| |
| cpu = <&CPU0>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| out-ports { |
| port { |
| etm0_out: endpoint { |
| remote-endpoint = |
| <&apss_funnel_in0>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@7140000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0 0x07140000 0 0x1000>; |
| |
| cpu = <&CPU1>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| out-ports { |
| port { |
| etm1_out: endpoint { |
| remote-endpoint = |
| <&apss_funnel_in1>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@7240000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0 0x07240000 0 0x1000>; |
| |
| cpu = <&CPU2>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| out-ports { |
| port { |
| etm2_out: endpoint { |
| remote-endpoint = |
| <&apss_funnel_in2>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@7340000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0 0x07340000 0 0x1000>; |
| |
| cpu = <&CPU3>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| out-ports { |
| port { |
| etm3_out: endpoint { |
| remote-endpoint = |
| <&apss_funnel_in3>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@7440000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0 0x07440000 0 0x1000>; |
| |
| cpu = <&CPU4>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| out-ports { |
| port { |
| etm4_out: endpoint { |
| remote-endpoint = |
| <&apss_funnel_in4>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@7540000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0 0x07540000 0 0x1000>; |
| |
| cpu = <&CPU5>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| out-ports { |
| port { |
| etm5_out: endpoint { |
| remote-endpoint = |
| <&apss_funnel_in5>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@7640000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0 0x07640000 0 0x1000>; |
| |
| cpu = <&CPU6>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| out-ports { |
| port { |
| etm6_out: endpoint { |
| remote-endpoint = |
| <&apss_funnel_in6>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@7740000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0 0x07740000 0 0x1000>; |
| |
| cpu = <&CPU7>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| out-ports { |
| port { |
| etm7_out: endpoint { |
| remote-endpoint = |
| <&apss_funnel_in7>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@7800000 { /* APSS Funnel */ |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0 0x07800000 0 0x1000>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| apss_funnel_out: endpoint { |
| remote-endpoint = |
| <&apss_merge_funnel_in>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| apss_funnel_in0: endpoint { |
| remote-endpoint = |
| <&etm0_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| apss_funnel_in1: endpoint { |
| remote-endpoint = |
| <&etm1_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| apss_funnel_in2: endpoint { |
| remote-endpoint = |
| <&etm2_out>; |
| }; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| apss_funnel_in3: endpoint { |
| remote-endpoint = |
| <&etm3_out>; |
| }; |
| }; |
| |
| port@4 { |
| reg = <4>; |
| apss_funnel_in4: endpoint { |
| remote-endpoint = |
| <&etm4_out>; |
| }; |
| }; |
| |
| port@5 { |
| reg = <5>; |
| apss_funnel_in5: endpoint { |
| remote-endpoint = |
| <&etm5_out>; |
| }; |
| }; |
| |
| port@6 { |
| reg = <6>; |
| apss_funnel_in6: endpoint { |
| remote-endpoint = |
| <&etm6_out>; |
| }; |
| }; |
| |
| port@7 { |
| reg = <7>; |
| apss_funnel_in7: endpoint { |
| remote-endpoint = |
| <&etm7_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@7810000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0 0x07810000 0 0x1000>; |
| |
| clocks = <&aoss_qmp>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| apss_merge_funnel_out: endpoint { |
| remote-endpoint = |
| <&funnel2_in5>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| port { |
| apss_merge_funnel_in: endpoint { |
| remote-endpoint = |
| <&apss_funnel_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| sdhc_2: mmc@8804000 { |
| compatible = "qcom,sdm845-sdhci", "qcom,sdhci-msm-v5"; |
| reg = <0 0x08804000 0 0x1000>; |
| |
| interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| |
| clocks = <&gcc GCC_SDCC2_AHB_CLK>, |
| <&gcc GCC_SDCC2_APPS_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "iface", "core", "xo"; |
| iommus = <&apps_smmu 0xa0 0xf>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&sdhc2_opp_table>; |
| |
| status = "disabled"; |
| |
| sdhc2_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-9600000 { |
| opp-hz = /bits/ 64 <9600000>; |
| required-opps = <&rpmhpd_opp_min_svs>; |
| }; |
| |
| opp-19200000 { |
| opp-hz = /bits/ 64 <19200000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-100000000 { |
| opp-hz = /bits/ 64 <100000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| |
| opp-201500000 { |
| opp-hz = /bits/ 64 <201500000>; |
| required-opps = <&rpmhpd_opp_svs_l1>; |
| }; |
| }; |
| }; |
| |
| qspi: spi@88df000 { |
| compatible = "qcom,sdm845-qspi", "qcom,qspi-v1"; |
| reg = <0 0x088df000 0 0x600>; |
| iommus = <&apps_smmu 0x160 0x0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>, |
| <&gcc GCC_QSPI_CORE_CLK>; |
| clock-names = "iface", "core"; |
| power-domains = <&rpmhpd SDM845_CX>; |
| operating-points-v2 = <&qspi_opp_table>; |
| status = "disabled"; |
| }; |
| |
| slim: slim-ngd@171c0000 { |
| compatible = "qcom,slim-ngd-v2.1.0"; |
| reg = <0 0x171c0000 0 0x2c000>; |
| interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dmas = <&slimbam 3>, <&slimbam 4>; |
| dma-names = "rx", "tx"; |
| |
| iommus = <&apps_smmu 0x1806 0x0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| lmh_cluster1: lmh@17d70800 { |
| compatible = "qcom,sdm845-lmh"; |
| reg = <0 0x17d70800 0 0x400>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| cpus = <&CPU4>; |
| qcom,lmh-temp-arm-millicelsius = <65000>; |
| qcom,lmh-temp-low-millicelsius = <94500>; |
| qcom,lmh-temp-high-millicelsius = <95000>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| }; |
| |
| lmh_cluster0: lmh@17d78800 { |
| compatible = "qcom,sdm845-lmh"; |
| reg = <0 0x17d78800 0 0x400>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| cpus = <&CPU0>; |
| qcom,lmh-temp-arm-millicelsius = <65000>; |
| qcom,lmh-temp-low-millicelsius = <94500>; |
| qcom,lmh-temp-high-millicelsius = <95000>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| }; |
| |
| usb_1_hsphy: phy@88e2000 { |
| compatible = "qcom,sdm845-qusb2-phy", "qcom,qusb2-v2-phy"; |
| reg = <0 0x088e2000 0 0x400>; |
| status = "disabled"; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "cfg_ahb", "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; |
| |
| nvmem-cells = <&qusb2p_hstx_trim>; |
| }; |
| |
| usb_2_hsphy: phy@88e3000 { |
| compatible = "qcom,sdm845-qusb2-phy", "qcom,qusb2-v2-phy"; |
| reg = <0 0x088e3000 0 0x400>; |
| status = "disabled"; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "cfg_ahb", "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_SEC_BCR>; |
| |
| nvmem-cells = <&qusb2s_hstx_trim>; |
| }; |
| |
| usb_1_qmpphy: phy@88e8000 { |
| compatible = "qcom,sdm845-qmp-usb3-dp-phy"; |
| reg = <0 0x088e8000 0 0x3000>; |
| status = "disabled"; |
| |
| clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>, |
| <&gcc GCC_USB3_PRIM_CLKREF_CLK>, |
| <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>, |
| <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>, |
| <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>; |
| clock-names = "aux", |
| "ref", |
| "com_aux", |
| "usb3_pipe", |
| "cfg_ahb"; |
| |
| resets = <&gcc GCC_USB3_PHY_PRIM_BCR>, |
| <&gcc GCC_USB3_DP_PHY_PRIM_BCR>; |
| reset-names = "phy", "common"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <1>; |
| }; |
| |
| usb_2_qmpphy: phy@88eb000 { |
| compatible = "qcom,sdm845-qmp-usb3-uni-phy"; |
| reg = <0 0x088eb000 0 0x18c>; |
| status = "disabled"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>, |
| <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, |
| <&gcc GCC_USB3_SEC_CLKREF_CLK>, |
| <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>; |
| clock-names = "aux", "cfg_ahb", "ref", "com_aux"; |
| |
| resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>, |
| <&gcc GCC_USB3_PHY_SEC_BCR>; |
| reset-names = "phy", "common"; |
| |
| usb_2_ssphy: phy@88eb200 { |
| reg = <0 0x088eb200 0 0x128>, |
| <0 0x088eb400 0 0x1fc>, |
| <0 0x088eb800 0 0x218>, |
| <0 0x088eb600 0 0x70>; |
| #clock-cells = <0>; |
| #phy-cells = <0>; |
| clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; |
| clock-names = "pipe0"; |
| clock-output-names = "usb3_uni_phy_pipe_clk_src"; |
| }; |
| }; |
| |
| usb_1: usb@a6f8800 { |
| compatible = "qcom,sdm845-dwc3", "qcom,dwc3"; |
| reg = <0 0x0a6f8800 0 0x400>; |
| status = "disabled"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| dma-ranges; |
| |
| clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>, |
| <&gcc GCC_USB30_PRIM_MASTER_CLK>, |
| <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>, |
| <&gcc GCC_USB30_PRIM_SLEEP_CLK>, |
| <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>; |
| clock-names = "cfg_noc", |
| "core", |
| "iface", |
| "sleep", |
| "mock_utmi"; |
| |
| assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB30_PRIM_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, <150000000>; |
| |
| interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hs_phy_irq", "ss_phy_irq", |
| "dm_hs_phy_irq", "dp_hs_phy_irq"; |
| |
| power-domains = <&gcc USB30_PRIM_GDSC>; |
| |
| resets = <&gcc GCC_USB30_PRIM_BCR>; |
| |
| interconnects = <&aggre2_noc MASTER_USB3_0 0 &mem_noc SLAVE_EBI1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_0 0>; |
| interconnect-names = "usb-ddr", "apps-usb"; |
| |
| usb_1_dwc3: usb@a600000 { |
| compatible = "snps,dwc3"; |
| reg = <0 0x0a600000 0 0xcd00>; |
| interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; |
| iommus = <&apps_smmu 0x740 0>; |
| snps,dis_u2_susphy_quirk; |
| snps,dis_enblslpm_quirk; |
| phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>; |
| phy-names = "usb2-phy", "usb3-phy"; |
| }; |
| }; |
| |
| usb_2: usb@a8f8800 { |
| compatible = "qcom,sdm845-dwc3", "qcom,dwc3"; |
| reg = <0 0x0a8f8800 0 0x400>; |
| status = "disabled"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| dma-ranges; |
| |
| clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>, |
| <&gcc GCC_USB30_SEC_MASTER_CLK>, |
| <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>, |
| <&gcc GCC_USB30_SEC_SLEEP_CLK>, |
| <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>; |
| clock-names = "cfg_noc", |
| "core", |
| "iface", |
| "sleep", |
| "mock_utmi"; |
| |
| assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB30_SEC_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, <150000000>; |
| |
| interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 490 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hs_phy_irq", "ss_phy_irq", |
| "dm_hs_phy_irq", "dp_hs_phy_irq"; |
| |
| power-domains = <&gcc USB30_SEC_GDSC>; |
| |
| resets = <&gcc GCC_USB30_SEC_BCR>; |
| |
| interconnects = <&aggre2_noc MASTER_USB3_1 0 &mem_noc SLAVE_EBI1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_1 0>; |
| interconnect-names = "usb-ddr", "apps-usb"; |
| |
| usb_2_dwc3: usb@a800000 { |
| compatible = "snps,dwc3"; |
| reg = <0 0x0a800000 0 0xcd00>; |
| interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; |
| iommus = <&apps_smmu 0x760 0>; |
| snps,dis_u2_susphy_quirk; |
| snps,dis_enblslpm_quirk; |
| phys = <&usb_2_hsphy>, <&usb_2_ssphy>; |
| phy-names = "usb2-phy", "usb3-phy"; |
| }; |
| }; |
| |
| venus: video-codec@aa00000 { |
| compatible = "qcom,sdm845-venus-v2"; |
| reg = <0 0x0aa00000 0 0xff000>; |
| interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&videocc VENUS_GDSC>, |
| <&videocc VCODEC0_GDSC>, |
| <&videocc VCODEC1_GDSC>, |
| <&rpmhpd SDM845_CX>; |
| power-domain-names = "venus", "vcodec0", "vcodec1", "cx"; |
| operating-points-v2 = <&venus_opp_table>; |
| clocks = <&videocc VIDEO_CC_VENUS_CTL_CORE_CLK>, |
| <&videocc VIDEO_CC_VENUS_AHB_CLK>, |
| <&videocc VIDEO_CC_VENUS_CTL_AXI_CLK>, |
| <&videocc VIDEO_CC_VCODEC0_CORE_CLK>, |
| <&videocc VIDEO_CC_VCODEC0_AXI_CLK>, |
| <&videocc VIDEO_CC_VCODEC1_CORE_CLK>, |
| <&videocc VIDEO_CC_VCODEC1_AXI_CLK>; |
| clock-names = "core", "iface", "bus", |
| "vcodec0_core", "vcodec0_bus", |
| "vcodec1_core", "vcodec1_bus"; |
| iommus = <&apps_smmu 0x10a0 0x8>, |
| <&apps_smmu 0x10b0 0x0>; |
| memory-region = <&venus_mem>; |
| interconnects = <&mmss_noc MASTER_VIDEO_P0 0 &mem_noc SLAVE_EBI1 0>, |
| <&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_VENUS_CFG 0>; |
| interconnect-names = "video-mem", "cpu-cfg"; |
| |
| status = "disabled"; |
| |
| video-core0 { |
| compatible = "venus-decoder"; |
| }; |
| |
| video-core1 { |
| compatible = "venus-encoder"; |
| }; |
| |
| venus_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-100000000 { |
| opp-hz = /bits/ 64 <100000000>; |
| required-opps = <&rpmhpd_opp_min_svs>; |
| }; |
| |
| opp-200000000 { |
| opp-hz = /bits/ 64 <200000000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-320000000 { |
| opp-hz = /bits/ 64 <320000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| |
| opp-380000000 { |
| opp-hz = /bits/ 64 <380000000>; |
| required-opps = <&rpmhpd_opp_svs_l1>; |
| }; |
| |
| opp-444000000 { |
| opp-hz = /bits/ 64 <444000000>; |
| required-opps = <&rpmhpd_opp_nom>; |
| }; |
| |
| opp-533000097 { |
| opp-hz = /bits/ 64 <533000097>; |
| required-opps = <&rpmhpd_opp_turbo>; |
| }; |
| }; |
| }; |
| |
| videocc: clock-controller@ab00000 { |
| compatible = "qcom,sdm845-videocc"; |
| reg = <0 0x0ab00000 0 0x10000>; |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "bi_tcxo"; |
| #clock-cells = <1>; |
| #power-domain-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| camss: camss@acb3000 { |
| compatible = "qcom,sdm845-camss"; |
| |
| reg = <0 0x0acb3000 0 0x1000>, |
| <0 0x0acba000 0 0x1000>, |
| <0 0x0acc8000 0 0x1000>, |
| <0 0x0ac65000 0 0x1000>, |
| <0 0x0ac66000 0 0x1000>, |
| <0 0x0ac67000 0 0x1000>, |
| <0 0x0ac68000 0 0x1000>, |
| <0 0x0acaf000 0 0x4000>, |
| <0 0x0acb6000 0 0x4000>, |
| <0 0x0acc4000 0 0x4000>; |
| reg-names = "csid0", |
| "csid1", |
| "csid2", |
| "csiphy0", |
| "csiphy1", |
| "csiphy2", |
| "csiphy3", |
| "vfe0", |
| "vfe1", |
| "vfe_lite"; |
| |
| interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "csid0", |
| "csid1", |
| "csid2", |
| "csiphy0", |
| "csiphy1", |
| "csiphy2", |
| "csiphy3", |
| "vfe0", |
| "vfe1", |
| "vfe_lite"; |
| |
| power-domains = <&clock_camcc IFE_0_GDSC>, |
| <&clock_camcc IFE_1_GDSC>, |
| <&clock_camcc TITAN_TOP_GDSC>; |
| |
| clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>, |
| <&clock_camcc CAM_CC_CPAS_AHB_CLK>, |
| <&clock_camcc CAM_CC_CPHY_RX_CLK_SRC>, |
| <&clock_camcc CAM_CC_IFE_0_CSID_CLK>, |
| <&clock_camcc CAM_CC_IFE_0_CSID_CLK_SRC>, |
| <&clock_camcc CAM_CC_IFE_1_CSID_CLK>, |
| <&clock_camcc CAM_CC_IFE_1_CSID_CLK_SRC>, |
| <&clock_camcc CAM_CC_IFE_LITE_CSID_CLK>, |
| <&clock_camcc CAM_CC_IFE_LITE_CSID_CLK_SRC>, |
| <&clock_camcc CAM_CC_CSIPHY0_CLK>, |
| <&clock_camcc CAM_CC_CSI0PHYTIMER_CLK>, |
| <&clock_camcc CAM_CC_CSI0PHYTIMER_CLK_SRC>, |
| <&clock_camcc CAM_CC_CSIPHY1_CLK>, |
| <&clock_camcc CAM_CC_CSI1PHYTIMER_CLK>, |
| <&clock_camcc CAM_CC_CSI1PHYTIMER_CLK_SRC>, |
| <&clock_camcc CAM_CC_CSIPHY2_CLK>, |
| <&clock_camcc CAM_CC_CSI2PHYTIMER_CLK>, |
| <&clock_camcc CAM_CC_CSI2PHYTIMER_CLK_SRC>, |
| <&clock_camcc CAM_CC_CSIPHY3_CLK>, |
| <&clock_camcc CAM_CC_CSI3PHYTIMER_CLK>, |
| <&clock_camcc CAM_CC_CSI3PHYTIMER_CLK_SRC>, |
| <&gcc GCC_CAMERA_AHB_CLK>, |
| <&gcc GCC_CAMERA_AXI_CLK>, |
| <&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>, |
| <&clock_camcc CAM_CC_SOC_AHB_CLK>, |
| <&clock_camcc CAM_CC_IFE_0_AXI_CLK>, |
| <&clock_camcc CAM_CC_IFE_0_CLK>, |
| <&clock_camcc CAM_CC_IFE_0_CPHY_RX_CLK>, |
| <&clock_camcc CAM_CC_IFE_0_CLK_SRC>, |
| <&clock_camcc CAM_CC_IFE_1_AXI_CLK>, |
| <&clock_camcc CAM_CC_IFE_1_CLK>, |
| <&clock_camcc CAM_CC_IFE_1_CPHY_RX_CLK>, |
| <&clock_camcc CAM_CC_IFE_1_CLK_SRC>, |
| <&clock_camcc CAM_CC_IFE_LITE_CLK>, |
| <&clock_camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>, |
| <&clock_camcc CAM_CC_IFE_LITE_CLK_SRC>; |
| clock-names = "camnoc_axi", |
| "cpas_ahb", |
| "cphy_rx_src", |
| "csi0", |
| "csi0_src", |
| "csi1", |
| "csi1_src", |
| "csi2", |
| "csi2_src", |
| "csiphy0", |
| "csiphy0_timer", |
| "csiphy0_timer_src", |
| "csiphy1", |
| "csiphy1_timer", |
| "csiphy1_timer_src", |
| "csiphy2", |
| "csiphy2_timer", |
| "csiphy2_timer_src", |
| "csiphy3", |
| "csiphy3_timer", |
| "csiphy3_timer_src", |
| "gcc_camera_ahb", |
| "gcc_camera_axi", |
| "slow_ahb_src", |
| "soc_ahb", |
| "vfe0_axi", |
| "vfe0", |
| "vfe0_cphy_rx", |
| "vfe0_src", |
| "vfe1_axi", |
| "vfe1", |
| "vfe1_cphy_rx", |
| "vfe1_src", |
| "vfe_lite", |
| "vfe_lite_cphy_rx", |
| "vfe_lite_src"; |
| |
| iommus = <&apps_smmu 0x0808 0x0>, |
| <&apps_smmu 0x0810 0x8>, |
| <&apps_smmu 0x0c08 0x0>, |
| <&apps_smmu 0x0c10 0x8>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| }; |
| }; |
| }; |
| |
| cci: cci@ac4a000 { |
| compatible = "qcom,sdm845-cci", "qcom,msm8996-cci"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| reg = <0 0x0ac4a000 0 0x4000>; |
| interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>; |
| power-domains = <&clock_camcc TITAN_TOP_GDSC>; |
| |
| clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>, |
| <&clock_camcc CAM_CC_SOC_AHB_CLK>, |
| <&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>, |
| <&clock_camcc CAM_CC_CPAS_AHB_CLK>, |
| <&clock_camcc CAM_CC_CCI_CLK>, |
| <&clock_camcc CAM_CC_CCI_CLK_SRC>; |
| clock-names = "camnoc_axi", |
| "soc_ahb", |
| "slow_ahb_src", |
| "cpas_ahb", |
| "cci", |
| "cci_src"; |
| |
| assigned-clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>, |
| <&clock_camcc CAM_CC_CCI_CLK>; |
| assigned-clock-rates = <80000000>, <37500000>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&cci0_default &cci1_default>; |
| pinctrl-1 = <&cci0_sleep &cci1_sleep>; |
| |
| status = "disabled"; |
| |
| cci_i2c0: i2c-bus@0 { |
| reg = <0>; |
| clock-frequency = <1000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| cci_i2c1: i2c-bus@1 { |
| reg = <1>; |
| clock-frequency = <1000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| clock_camcc: clock-controller@ad00000 { |
| compatible = "qcom,sdm845-camcc"; |
| reg = <0 0x0ad00000 0 0x10000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "bi_tcxo"; |
| }; |
| |
| mdss: display-subsystem@ae00000 { |
| compatible = "qcom,sdm845-mdss"; |
| reg = <0 0x0ae00000 0 0x1000>; |
| reg-names = "mdss"; |
| |
| power-domains = <&dispcc MDSS_GDSC>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&dispcc DISP_CC_MDSS_MDP_CLK>; |
| clock-names = "iface", "core"; |
| |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| |
| interconnects = <&mmss_noc MASTER_MDP0 0 &mem_noc SLAVE_EBI1 0>, |
| <&mmss_noc MASTER_MDP1 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "mdp0-mem", "mdp1-mem"; |
| |
| iommus = <&apps_smmu 0x880 0x8>, |
| <&apps_smmu 0xc80 0x8>; |
| |
| status = "disabled"; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| mdss_mdp: display-controller@ae01000 { |
| compatible = "qcom,sdm845-dpu"; |
| reg = <0 0x0ae01000 0 0x8f000>, |
| <0 0x0aeb0000 0 0x2008>; |
| reg-names = "mdp", "vbif"; |
| |
| clocks = <&gcc GCC_DISP_AXI_CLK>, |
| <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&dispcc DISP_CC_MDSS_AXI_CLK>, |
| <&dispcc DISP_CC_MDSS_MDP_CLK>, |
| <&dispcc DISP_CC_MDSS_VSYNC_CLK>; |
| clock-names = "gcc-bus", "iface", "bus", "core", "vsync"; |
| |
| assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; |
| assigned-clock-rates = <19200000>; |
| operating-points-v2 = <&mdp_opp_table>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <0>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| dpu_intf0_out: endpoint { |
| remote-endpoint = <&dp_in>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| dpu_intf1_out: endpoint { |
| remote-endpoint = <&mdss_dsi0_in>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| dpu_intf2_out: endpoint { |
| remote-endpoint = <&mdss_dsi1_in>; |
| }; |
| }; |
| }; |
| |
| mdp_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-19200000 { |
| opp-hz = /bits/ 64 <19200000>; |
| required-opps = <&rpmhpd_opp_min_svs>; |
| }; |
| |
| opp-171428571 { |
| opp-hz = /bits/ 64 <171428571>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-344000000 { |
| opp-hz = /bits/ 64 <344000000>; |
| required-opps = <&rpmhpd_opp_svs_l1>; |
| }; |
| |
| opp-430000000 { |
| opp-hz = /bits/ 64 <430000000>; |
| required-opps = <&rpmhpd_opp_nom>; |
| }; |
| }; |
| }; |
| |
| mdss_dp: displayport-controller@ae90000 { |
| status = "disabled"; |
| compatible = "qcom,sdm845-dp"; |
| |
| reg = <0 0x0ae90000 0 0x200>, |
| <0 0x0ae90200 0 0x200>, |
| <0 0x0ae90400 0 0x600>, |
| <0 0x0ae90a00 0 0x600>, |
| <0 0x0ae91000 0 0x600>; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <12>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&dispcc DISP_CC_MDSS_DP_AUX_CLK>, |
| <&dispcc DISP_CC_MDSS_DP_LINK_CLK>, |
| <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>, |
| <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>; |
| clock-names = "core_iface", "core_aux", "ctrl_link", |
| "ctrl_link_iface", "stream_pixel"; |
| assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>, |
| <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>; |
| assigned-clock-parents = <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>, |
| <&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>; |
| phys = <&usb_1_qmpphy QMP_USB43DP_DP_PHY>; |
| phy-names = "dp"; |
| |
| operating-points-v2 = <&dp_opp_table>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| port@0 { |
| reg = <0>; |
| dp_in: endpoint { |
| remote-endpoint = <&dpu_intf0_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| dp_out: endpoint { }; |
| }; |
| }; |
| |
| dp_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-162000000 { |
| opp-hz = /bits/ 64 <162000000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-270000000 { |
| opp-hz = /bits/ 64 <270000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| |
| opp-540000000 { |
| opp-hz = /bits/ 64 <540000000>; |
| required-opps = <&rpmhpd_opp_svs_l1>; |
| }; |
| |
| opp-810000000 { |
| opp-hz = /bits/ 64 <810000000>; |
| required-opps = <&rpmhpd_opp_nom>; |
| }; |
| }; |
| }; |
| |
| mdss_dsi0: dsi@ae94000 { |
| compatible = "qcom,sdm845-dsi-ctrl", |
| "qcom,mdss-dsi-ctrl"; |
| reg = <0 0x0ae94000 0 0x400>; |
| reg-names = "dsi_ctrl"; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <4>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, |
| <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, |
| <&dispcc DISP_CC_MDSS_PCLK0_CLK>, |
| <&dispcc DISP_CC_MDSS_ESC0_CLK>, |
| <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&dispcc DISP_CC_MDSS_AXI_CLK>; |
| clock-names = "byte", |
| "byte_intf", |
| "pixel", |
| "core", |
| "iface", |
| "bus"; |
| assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; |
| assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>; |
| |
| operating-points-v2 = <&dsi_opp_table>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| |
| phys = <&mdss_dsi0_phy>; |
| |
| status = "disabled"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| mdss_dsi0_in: endpoint { |
| remote-endpoint = <&dpu_intf1_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| mdss_dsi0_out: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| mdss_dsi0_phy: phy@ae94400 { |
| compatible = "qcom,dsi-phy-10nm"; |
| reg = <0 0x0ae94400 0 0x200>, |
| <0 0x0ae94600 0 0x280>, |
| <0 0x0ae94a00 0 0x1e0>; |
| reg-names = "dsi_phy", |
| "dsi_phy_lane", |
| "dsi_pll"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "iface", "ref"; |
| |
| status = "disabled"; |
| }; |
| |
| mdss_dsi1: dsi@ae96000 { |
| compatible = "qcom,sdm845-dsi-ctrl", |
| "qcom,mdss-dsi-ctrl"; |
| reg = <0 0x0ae96000 0 0x400>; |
| reg-names = "dsi_ctrl"; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <5>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>, |
| <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>, |
| <&dispcc DISP_CC_MDSS_PCLK1_CLK>, |
| <&dispcc DISP_CC_MDSS_ESC1_CLK>, |
| <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&dispcc DISP_CC_MDSS_AXI_CLK>; |
| clock-names = "byte", |
| "byte_intf", |
| "pixel", |
| "core", |
| "iface", |
| "bus"; |
| assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>; |
| assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>; |
| |
| operating-points-v2 = <&dsi_opp_table>; |
| power-domains = <&rpmhpd SDM845_CX>; |
| |
| phys = <&mdss_dsi1_phy>; |
| |
| status = "disabled"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| mdss_dsi1_in: endpoint { |
| remote-endpoint = <&dpu_intf2_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| mdss_dsi1_out: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| mdss_dsi1_phy: phy@ae96400 { |
| compatible = "qcom,dsi-phy-10nm"; |
| reg = <0 0x0ae96400 0 0x200>, |
| <0 0x0ae96600 0 0x280>, |
| <0 0x0ae96a00 0 0x10e>; |
| reg-names = "dsi_phy", |
| "dsi_phy_lane", |
| "dsi_pll"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "iface", "ref"; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| gpu: gpu@5000000 { |
| compatible = "qcom,adreno-630.2", "qcom,adreno"; |
| |
| reg = <0 0x05000000 0 0x40000>, <0 0x509e000 0 0x10>; |
| reg-names = "kgsl_3d0_reg_memory", "cx_mem"; |
| |
| /* |
| * Look ma, no clocks! The GPU clocks and power are |
| * controlled entirely by the GMU |
| */ |
| |
| interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; |
| |
| iommus = <&adreno_smmu 0>; |
| |
| operating-points-v2 = <&gpu_opp_table>; |
| |
| qcom,gmu = <&gmu>; |
| |
| interconnects = <&mem_noc MASTER_GFX3D 0 &mem_noc SLAVE_EBI1 0>; |
| interconnect-names = "gfx-mem"; |
| |
| status = "disabled"; |
| |
| gpu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-710000000 { |
| opp-hz = /bits/ 64 <710000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; |
| opp-peak-kBps = <7216000>; |
| }; |
| |
| opp-675000000 { |
| opp-hz = /bits/ 64 <675000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; |
| opp-peak-kBps = <7216000>; |
| }; |
| |
| opp-596000000 { |
| opp-hz = /bits/ 64 <596000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; |
| opp-peak-kBps = <6220000>; |
| }; |
| |
| opp-520000000 { |
| opp-hz = /bits/ 64 <520000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM>; |
| opp-peak-kBps = <6220000>; |
| }; |
| |
| opp-414000000 { |
| opp-hz = /bits/ 64 <414000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; |
| opp-peak-kBps = <4068000>; |
| }; |
| |
| opp-342000000 { |
| opp-hz = /bits/ 64 <342000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS>; |
| opp-peak-kBps = <2724000>; |
| }; |
| |
| opp-257000000 { |
| opp-hz = /bits/ 64 <257000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; |
| opp-peak-kBps = <1648000>; |
| }; |
| }; |
| }; |
| |
| adreno_smmu: iommu@5040000 { |
| compatible = "qcom,sdm845-smmu-v2", "qcom,adreno-smmu", "qcom,smmu-v2"; |
| reg = <0 0x05040000 0 0x10000>; |
| #iommu-cells = <1>; |
| #global-interrupts = <2>; |
| interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 364 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 365 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 366 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 367 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 368 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 369 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 370 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 371 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&gcc GCC_GPU_MEMNOC_GFX_CLK>, |
| <&gcc GCC_GPU_CFG_AHB_CLK>; |
| clock-names = "bus", "iface"; |
| |
| power-domains = <&gpucc GPU_CX_GDSC>; |
| }; |
| |
| gmu: gmu@506a000 { |
| compatible = "qcom,adreno-gmu-630.2", "qcom,adreno-gmu"; |
| |
| reg = <0 0x0506a000 0 0x30000>, |
| <0 0x0b280000 0 0x10000>, |
| <0 0x0b480000 0 0x10000>; |
| reg-names = "gmu", "gmu_pdc", "gmu_pdc_seq"; |
| |
| interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hfi", "gmu"; |
| |
| clocks = <&gpucc GPU_CC_CX_GMU_CLK>, |
| <&gpucc GPU_CC_CXO_CLK>, |
| <&gcc GCC_DDRSS_GPU_AXI_CLK>, |
| <&gcc GCC_GPU_MEMNOC_GFX_CLK>; |
| clock-names = "gmu", "cxo", "axi", "memnoc"; |
| |
| power-domains = <&gpucc GPU_CX_GDSC>, |
| <&gpucc GPU_GX_GDSC>; |
| power-domain-names = "cx", "gx"; |
| |
| iommus = <&adreno_smmu 5>; |
| |
| operating-points-v2 = <&gmu_opp_table>; |
| |
| status = "disabled"; |
| |
| gmu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-400000000 { |
| opp-hz = /bits/ 64 <400000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS>; |
| }; |
| |
| opp-200000000 { |
| opp-hz = /bits/ 64 <200000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; |
| }; |
| }; |
| }; |
| |
| dispcc: clock-controller@af00000 { |
| compatible = "qcom,sdm845-dispcc"; |
| reg = <0 0x0af00000 0 0x10000>; |
| clocks = <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_DISP_GPLL0_CLK_SRC>, |
| <&gcc GCC_DISP_GPLL0_DIV_CLK_SRC>, |
| <&mdss_dsi0_phy 0>, |
| <&mdss_dsi0_phy 1>, |
| <&mdss_dsi1_phy 0>, |
| <&mdss_dsi1_phy 1>, |
| <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>, |
| <&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>; |
| clock-names = "bi_tcxo", |
| "gcc_disp_gpll0_clk_src", |
| "gcc_disp_gpll0_div_clk_src", |
| "dsi0_phy_pll_out_byteclk", |
| "dsi0_phy_pll_out_dsiclk", |
| "dsi1_phy_pll_out_byteclk", |
| "dsi1_phy_pll_out_dsiclk", |
| "dp_link_clk_divsel_ten", |
| "dp_vco_divided_clk_src_mux"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| }; |
| |
| pdc_intc: interrupt-controller@b220000 { |
| compatible = "qcom,sdm845-pdc", "qcom,pdc"; |
| reg = <0 0x0b220000 0 0x30000>; |
| qcom,pdc-ranges = <0 480 94>, <94 609 15>, <115 630 7>; |
| #interrupt-cells = <2>; |
| interrupt-parent = <&intc>; |
| interrupt-controller; |
| }; |
| |
| pdc_reset: reset-controller@b2e0000 { |
| compatible = "qcom,sdm845-pdc-global"; |
| reg = <0 0x0b2e0000 0 0x20000>; |
| #reset-cells = <1>; |
| }; |
| |
| tsens0: thermal-sensor@c263000 { |
| compatible = "qcom,sdm845-tsens", "qcom,tsens-v2"; |
| reg = <0 0x0c263000 0 0x1ff>, /* TM */ |
| <0 0x0c222000 0 0x1ff>; /* SROT */ |
| #qcom,sensors = <13>; |
| interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", "critical"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| tsens1: thermal-sensor@c265000 { |
| compatible = "qcom,sdm845-tsens", "qcom,tsens-v2"; |
| reg = <0 0x0c265000 0 0x1ff>, /* TM */ |
| <0 0x0c223000 0 0x1ff>; /* SROT */ |
| #qcom,sensors = <8>; |
| interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", "critical"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| aoss_reset: reset-controller@c2a0000 { |
| compatible = "qcom,sdm845-aoss-cc"; |
| reg = <0 0x0c2a0000 0 0x31000>; |
| #reset-cells = <1>; |
| }; |
| |
| aoss_qmp: power-management@c300000 { |
| compatible = "qcom,sdm845-aoss-qmp", "qcom,aoss-qmp"; |
| reg = <0 0x0c300000 0 0x400>; |
| interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&apss_shared 0>; |
| |
| #clock-cells = <0>; |
| |
| cx_cdev: cx { |
| #cooling-cells = <2>; |
| }; |
| |
| ebi_cdev: ebi { |
| #cooling-cells = <2>; |
| }; |
| }; |
| |
| sram@c3f0000 { |
| compatible = "qcom,sdm845-rpmh-stats"; |
| reg = <0 0x0c3f0000 0 0x400>; |
| }; |
| |
| spmi_bus: spmi@c440000 { |
| compatible = "qcom,spmi-pmic-arb"; |
| reg = <0 0x0c440000 0 0x1100>, |
| <0 0x0c600000 0 0x2000000>, |
| <0 0x0e600000 0 0x100000>, |
| <0 0x0e700000 0 0xa0000>, |
| <0 0x0c40a000 0 0x26000>; |
| reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; |
| interrupt-names = "periph_irq"; |
| interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,ee = <0>; |
| qcom,channel = <0>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| interrupt-controller; |
| #interrupt-cells = <4>; |
| }; |
| |
| sram@146bf000 { |
| compatible = "qcom,sdm845-imem", "syscon", "simple-mfd"; |
| reg = <0 0x146bf000 0 0x1000>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| ranges = <0 0 0x146bf000 0x1000>; |
| |
| pil-reloc@94c { |
| compatible = "qcom,pil-reloc-info"; |
| reg = <0x94c 0xc8>; |
| }; |
| }; |
| |
| apps_smmu: iommu@15000000 { |
| compatible = "qcom,sdm845-smmu-500", "arm,mmu-500"; |
| reg = <0 0x15000000 0 0x80000>; |
| #iommu-cells = <2>; |
| #global-interrupts = <1>; |
| interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| lpasscc: clock-controller@17014000 { |
| compatible = "qcom,sdm845-lpasscc"; |
| reg = <0 0x17014000 0 0x1f004>, <0 0x17300000 0 0x200>; |
| reg-names = "cc", "qdsp6ss"; |
| #clock-cells = <1>; |
| status = "disabled"; |
| }; |
| |
| gladiator_noc: interconnect@17900000 { |
| compatible = "qcom,sdm845-gladiator-noc"; |
| reg = <0 0x17900000 0 0xd080>; |
| #interconnect-cells = <2>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| watchdog@17980000 { |
| compatible = "qcom,apss-wdt-sdm845", "qcom,kpss-wdt"; |
| reg = <0 0x17980000 0 0x1000>; |
| clocks = <&sleep_clk>; |
| interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| apss_shared: mailbox@17990000 { |
| compatible = "qcom,sdm845-apss-shared"; |
| reg = <0 0x17990000 0 0x1000>; |
| #mbox-cells = <1>; |
| }; |
| |
| apps_rsc: rsc@179c0000 { |
| label = "apps_rsc"; |
| compatible = "qcom,rpmh-rsc"; |
| reg = <0 0x179c0000 0 0x10000>, |
| <0 0x179d0000 0 0x10000>, |
| <0 0x179e0000 0 0x10000>; |
| reg-names = "drv-0", "drv-1", "drv-2"; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,tcs-offset = <0xd00>; |
| qcom,drv-id = <2>; |
| qcom,tcs-config = <ACTIVE_TCS 2>, |
| <SLEEP_TCS 3>, |
| <WAKE_TCS 3>, |
| <CONTROL_TCS 1>; |
| power-domains = <&CLUSTER_PD>; |
| |
| apps_bcm_voter: bcm-voter { |
| compatible = "qcom,bcm-voter"; |
| }; |
| |
| rpmhcc: clock-controller { |
| compatible = "qcom,sdm845-rpmh-clk"; |
| #clock-cells = <1>; |
| clock-names = "xo"; |
| clocks = <&xo_board>; |
| }; |
| |
| rpmhpd: power-controller { |
| compatible = "qcom,sdm845-rpmhpd"; |
| #power-domain-cells = <1>; |
| operating-points-v2 = <&rpmhpd_opp_table>; |
| |
| rpmhpd_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| rpmhpd_opp_ret: opp1 { |
| opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; |
| }; |
| |
| rpmhpd_opp_min_svs: opp2 { |
| opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; |
| }; |
| |
| rpmhpd_opp_low_svs: opp3 { |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; |
| }; |
| |
| rpmhpd_opp_svs: opp4 { |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS>; |
| }; |
| |
| rpmhpd_opp_svs_l1: opp5 { |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; |
| }; |
| |
| rpmhpd_opp_nom: opp6 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM>; |
| }; |
| |
| rpmhpd_opp_nom_l1: opp7 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; |
| }; |
| |
| rpmhpd_opp_nom_l2: opp8 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>; |
| }; |
| |
| rpmhpd_opp_turbo: opp9 { |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; |
| }; |
| |
| rpmhpd_opp_turbo_l1: opp10 { |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; |
| }; |
| }; |
| }; |
| }; |
| |
| intc: interrupt-controller@17a00000 { |
| compatible = "arm,gic-v3"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0 0x17a00000 0 0x10000>, /* GICD */ |
| <0 0x17a60000 0 0x100000>; /* GICR * 8 */ |
| interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| |
| msi-controller@17a40000 { |
| compatible = "arm,gic-v3-its"; |
| msi-controller; |
| #msi-cells = <1>; |
| reg = <0 0x17a40000 0 0x20000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| slimbam: dma-controller@17184000 { |
| compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0"; |
| qcom,controlled-remotely; |
| reg = <0 0x17184000 0 0x2a000>; |
| num-channels = <31>; |
| interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; |
| #dma-cells = <1>; |
| qcom,ee = <1>; |
| qcom,num-ees = <2>; |
| iommus = <&apps_smmu 0x1806 0x0>; |
| }; |
| |
| timer@17c90000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0 0 0x20000000>; |
| compatible = "arm,armv7-timer-mem"; |
| reg = <0 0x17c90000 0 0x1000>; |
| |
| frame@17ca0000 { |
| frame-number = <0>; |
| interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17ca0000 0x1000>, |
| <0x17cb0000 0x1000>; |
| }; |
| |
| frame@17cc0000 { |
| frame-number = <1>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17cc0000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17cd0000 { |
| frame-number = <2>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17cd0000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17ce0000 { |
| frame-number = <3>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17ce0000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17cf0000 { |
| frame-number = <4>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17cf0000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17d00000 { |
| frame-number = <5>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17d00000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17d10000 { |
| frame-number = <6>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17d10000 0x1000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| osm_l3: interconnect@17d41000 { |
| compatible = "qcom,sdm845-osm-l3", "qcom,osm-l3"; |
| reg = <0 0x17d41000 0 0x1400>; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>; |
| clock-names = "xo", "alternate"; |
| |
| #interconnect-cells = <1>; |
| }; |
| |
| cpufreq_hw: cpufreq@17d43000 { |
| compatible = "qcom,sdm845-cpufreq-hw", "qcom,cpufreq-hw"; |
| reg = <0 0x17d43000 0 0x1400>, <0 0x17d45800 0 0x1400>; |
| reg-names = "freq-domain0", "freq-domain1"; |
| |
| interrupts-extended = <&lmh_cluster0 0>, <&lmh_cluster1 0>; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>; |
| clock-names = "xo", "alternate"; |
| |
| #freq-domain-cells = <1>; |
| #clock-cells = <1>; |
| }; |
| |
| wifi: wifi@18800000 { |
| compatible = "qcom,wcn3990-wifi"; |
| status = "disabled"; |
| reg = <0 0x18800000 0 0x800000>; |
| reg-names = "membase"; |
| memory-region = <&wlan_msa_mem>; |
| clock-names = "cxo_ref_clk_pin"; |
| clocks = <&rpmhcc RPMH_RF_CLK2>; |
| interrupts = |
| <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>; |
| iommus = <&apps_smmu 0x0040 0x1>; |
| }; |
| }; |
| |
| sound: sound { |
| }; |
| |
| thermal-zones { |
| cpu0-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 1>; |
| |
| trips { |
| cpu0_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu0_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu0_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 2>; |
| |
| trips { |
| cpu1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu1_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu1_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu2-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 3>; |
| |
| trips { |
| cpu2_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu2_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu2_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu3-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 4>; |
| |
| trips { |
| cpu3_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu3_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu3_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu4-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 7>; |
| |
| trips { |
| cpu4_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu5-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 8>; |
| |
| trips { |
| cpu5_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu6-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 9>; |
| |
| trips { |
| cpu6_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu7-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 10>; |
| |
| trips { |
| cpu7_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| aoss0-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 0>; |
| |
| trips { |
| aoss0_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| cluster0-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 5>; |
| |
| trips { |
| cluster0_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| cluster0_crit: cluster0_crit { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cluster1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 6>; |
| |
| trips { |
| cluster1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| cluster1_crit: cluster1_crit { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpu-top-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 11>; |
| |
| trips { |
| gpu1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| gpu-bottom-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 12>; |
| |
| trips { |
| gpu2_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| aoss1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 0>; |
| |
| trips { |
| aoss1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| q6-modem-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 1>; |
| |
| trips { |
| q6_modem_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| mem-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 2>; |
| |
| trips { |
| mem_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| wlan-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 3>; |
| |
| trips { |
| wlan_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| q6-hvx-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 4>; |
| |
| trips { |
| q6_hvx_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| camera-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 5>; |
| |
| trips { |
| camera_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| video-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 6>; |
| |
| trips { |
| video_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| modem-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 7>; |
| |
| trips { |
| modem_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| }; |