| // SPDX-License-Identifier: (GPL-2.0 OR MIT) |
| /* |
| * Copyright 2020 Compass Electronics Group, LLC |
| */ |
| |
| / { |
| leds { |
| compatible = "gpio-leds"; |
| |
| led-0 { |
| label = "gen_led0"; |
| gpios = <&pca6416_1 4 GPIO_ACTIVE_HIGH>; |
| default-state = "off"; |
| }; |
| |
| led-1 { |
| label = "gen_led1"; |
| gpios = <&pca6416_1 5 GPIO_ACTIVE_HIGH>; |
| default-state = "off"; |
| }; |
| |
| led-2 { |
| label = "gen_led2"; |
| gpios = <&pca6416_1 6 GPIO_ACTIVE_HIGH>; |
| default-state = "off"; |
| }; |
| |
| led-3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_led3>; |
| label = "heartbeat"; |
| gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| |
| reg_usdhc2_vmmc: regulator-usdhc2 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vsd_3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_usb_otg_vbus: regulator-usb { |
| compatible = "regulator-fixed"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_reg_usb_otg>; |
| regulator-name = "usb_otg_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| }; |
| |
| &ecspi2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_espi2>; |
| cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| |
| eeprom@0 { |
| compatible = "microchip,at25160bn", "atmel,at25"; |
| reg = <0>; |
| spi-max-frequency = <5000000>; |
| spi-cpha; |
| spi-cpol; |
| pagesize = <32>; |
| size = <2048>; |
| address-width = <16>; |
| }; |
| }; |
| |
| &i2c4 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c4>; |
| status = "okay"; |
| |
| pca6416_0: gpio@20 { |
| compatible = "nxp,pcal6416"; |
| reg = <0x20>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pcal6414>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-parent = <&gpio4>; |
| interrupts = <27 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| |
| pca6416_1: gpio@21 { |
| compatible = "nxp,pcal6416"; |
| reg = <0x21>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-parent = <&gpio4>; |
| interrupts = <27 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| }; |
| |
| &snvs_pwrkey { |
| status = "okay"; |
| }; |
| |
| &uart2 { /* console */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| assigned-clocks = <&clk IMX8MN_CLK_UART3>; |
| assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>; |
| status = "okay"; |
| }; |
| |
| &usbotg1 { |
| vbus-supply = <®_usb_otg_vbus>; |
| disable-over-current; |
| dr_mode="otg"; |
| status = "okay"; |
| }; |
| |
| &usdhc2 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-1 = <&pinctrl_usdhc2_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc2_200mhz>; |
| bus-width = <4>; |
| vmmc-supply = <®_usdhc2_vmmc>; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_espi2: espi2grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82 |
| MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82 |
| MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82 |
| MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x41 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 |
| MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_i2c4: i2c4grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3 |
| MX8MN_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_led3: led3grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x41 |
| >; |
| }; |
| |
| pinctrl_pcal6414: pcal6414-gpiogrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x19 |
| >; |
| }; |
| |
| pinctrl_reg_usb_otg: reg-otggrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SAI3_RXC_GPIO4_IO29 0x19 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 |
| MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 |
| >; |
| }; |
| |
| pinctrl_uart3: uart3grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX 0x40 |
| MX8MN_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX 0x40 |
| >; |
| }; |
| |
| pinctrl_usdhc2_gpio: usdhc2gpiogrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x41 |
| MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 |
| MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 |
| MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 |
| MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 |
| MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 |
| MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 |
| MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 |
| MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 |
| MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 |
| MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 |
| MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 |
| MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 |
| MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 |
| MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 |
| MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 |
| MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 |
| MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 |
| MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 |
| MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| }; |