board/freescale/mx6slevk/mx6slevk.c

/*
 * Copyright (C) 2013 Freescale Semiconductor, Inc.
 *
 * Author: Fabio Estevam <fabio.estevam@freescale.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <asm/arch/clock.h>
#include <asm/arch/iomux.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
#include <asm/imx-common/spi.h>
#include <asm/io.h>
#include <linux/sizes.h>
#include <common.h>
#include <fsl_esdhc.h>
#include <mmc.h>
#include <netdev.h>

DECLARE_GLOBAL_DATA_PTR;

#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

#define USDHC_PAD_CTRL (PAD_CTL_PUS_22K_UP |			\
	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

#define ENET_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |             \
	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED   |             \
	PAD_CTL_DSE_40ohm   | PAD_CTL_HYS)

#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)

#define ETH_PHY_RESET	IMX_GPIO_NR(4, 21)

int dram_init(void)
{
	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);

	return 0;
}

static iomux_v3_cfg_t const uart1_pads[] = {
	MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
	MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
};

static iomux_v3_cfg_t const usdhc1_pads[] = {
	/* 8 bit SD */
	MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DAT0__USDHC1_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DAT1__USDHC1_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DAT2__USDHC1_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DAT3__USDHC1_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DAT4__USDHC1_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DAT5__USDHC1_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DAT6__USDHC1_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DAT7__USDHC1_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),

	/*CD pin*/
	MX6_PAD_KEY_ROW7__GPIO_4_7 | MUX_PAD_CTRL(NO_PAD_CTRL),
};

static iomux_v3_cfg_t const usdhc2_pads[] = {
	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),

	/*CD pin*/
	MX6_PAD_SD2_DAT7__GPIO_5_0 | MUX_PAD_CTRL(NO_PAD_CTRL),
};

static iomux_v3_cfg_t const usdhc3_pads[] = {
	MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),

	/*CD pin*/
	MX6_PAD_REF_CLK_32K__GPIO_3_22 | MUX_PAD_CTRL(NO_PAD_CTRL),
};

static iomux_v3_cfg_t const fec_pads[] = {
	MX6_PAD_FEC_MDC__FEC_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_FEC_MDIO__FEC_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_FEC_CRS_DV__FEC_RX_DV | MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_FEC_RXD0__FEC_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_FEC_RXD1__FEC_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_FEC_TX_EN__FEC_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_FEC_TXD0__FEC_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_FEC_TXD1__FEC_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_FEC_REF_CLK__FEC_REF_OUT | MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_FEC_RX_ER__GPIO_4_19 | MUX_PAD_CTRL(NO_PAD_CTRL),
	MX6_PAD_FEC_TX_CLK__GPIO_4_21 | MUX_PAD_CTRL(NO_PAD_CTRL),
};

#ifdef CONFIG_MXC_SPI
static iomux_v3_cfg_t ecspi1_pads[] = {
	MX6_PAD_ECSPI1_MISO__ECSPI_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
	MX6_PAD_ECSPI1_MOSI__ECSPI_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
	MX6_PAD_ECSPI1_SCLK__ECSPI_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
	MX6_PAD_ECSPI1_SS0__GPIO4_IO11  | MUX_PAD_CTRL(NO_PAD_CTRL),
};

int board_spi_cs_gpio(unsigned bus, unsigned cs)
{
	return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 11)) : -1;
}

static void setup_spi(void)
{
	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
}
#endif

static void setup_iomux_uart(void)
{
	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}

static void setup_iomux_fec(void)
{
	imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));

	/* Reset LAN8720 PHY */
	gpio_direction_output(ETH_PHY_RESET , 0);
	udelay(1000);
	gpio_set_value(ETH_PHY_RESET, 1);
}

#define USDHC1_CD_GPIO	IMX_GPIO_NR(4, 7)
#define USDHC2_CD_GPIO	IMX_GPIO_NR(5, 0)
#define USDHC3_CD_GPIO	IMX_GPIO_NR(3, 22)

static struct fsl_esdhc_cfg usdhc_cfg[3] = {
	{USDHC1_BASE_ADDR},
	{USDHC2_BASE_ADDR, 0, 4},
	{USDHC3_BASE_ADDR, 0, 4},
};

int board_mmc_getcd(struct mmc *mmc)
{
	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
	int ret = 0;

	switch (cfg->esdhc_base) {
	case USDHC1_BASE_ADDR:
		ret = !gpio_get_value(USDHC1_CD_GPIO);
		break;
	case USDHC2_BASE_ADDR:
		ret = !gpio_get_value(USDHC2_CD_GPIO);
		break;
	case USDHC3_BASE_ADDR:
		ret = !gpio_get_value(USDHC3_CD_GPIO);
		break;
	}

	return ret;
}

int board_mmc_init(bd_t *bis)
{
	int i, ret;

	/*
	 * According to the board_mmc_init() the following map is done:
	 * (U-boot device node)    (Physical Port)
	 * mmc0                    USDHC1
	 * mmc1                    USDHC2
	 * mmc2                    USDHC3
	 */
	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
		switch (i) {
		case 0:
			imx_iomux_v3_setup_multiple_pads(
				usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
			gpio_direction_input(USDHC1_CD_GPIO);
			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
			break;
		case 1:
			imx_iomux_v3_setup_multiple_pads(
				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
			gpio_direction_input(USDHC2_CD_GPIO);
			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
			break;
		case 2:
			imx_iomux_v3_setup_multiple_pads(
				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
			gpio_direction_input(USDHC3_CD_GPIO);
			usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
			break;
		default:
			printf("Warning: you configured more USDHC controllers"
				"(%d) than supported by the board\n", i + 1);
			return -EINVAL;
			}

			ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
			if (ret) {
				printf("Warning: failed to initialize "
					"mmc dev %d\n", i);
				return ret;
			}
	}

	return 0;
}

#ifdef CONFIG_FEC_MXC
int board_eth_init(bd_t *bis)
{
	setup_iomux_fec();

	return cpu_eth_init(bis);
}

static int setup_fec(void)
{
	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
	int ret;

	/* clear gpr1[14], gpr1[18:17] to select anatop clock */
	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC_MASK, 0);

	ret = enable_fec_anatop_clock(ENET_50MHz);
	if (ret)
		return ret;

	return 0;
}
#endif


int board_early_init_f(void)
{
	setup_iomux_uart();
#ifdef CONFIG_MXC_SPI
	setup_spi();
#endif
	return 0;
}

int board_init(void)
{
	/* address of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

#ifdef	CONFIG_FEC_MXC
	setup_fec();
#endif
	return 0;
}

u32 get_board_rev(void)
{
	return get_cpu_rev();
}

int checkboard(void)
{
	puts("Board: MX6SLEVK\n");

	return 0;
}