| /* |
| * Xilinx Zynq 7000 DTSI |
| * Describes the hardware common to all Zynq 7000-based boards. |
| * |
| * Copyright (C) 2011 - 2015 Xilinx |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "xlnx,zynq-7000"; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| compatible = "arm,cortex-a9"; |
| device_type = "cpu"; |
| reg = <0>; |
| clocks = <&clkc 3>; |
| clock-latency = <1000>; |
| cpu0-supply = <®ulator_vccpint>; |
| operating-points = < |
| /* kHz uV */ |
| 666667 1000000 |
| 333334 1000000 |
| >; |
| }; |
| |
| cpu1: cpu@1 { |
| compatible = "arm,cortex-a9"; |
| device_type = "cpu"; |
| reg = <1>; |
| clocks = <&clkc 3>; |
| }; |
| }; |
| |
| fpga_full: fpga-full { |
| compatible = "fpga-region"; |
| fpga-mgr = <&devcfg>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| }; |
| |
| pmu@f8891000 { |
| compatible = "arm,cortex-a9-pmu"; |
| interrupts = <0 5 4>, <0 6 4>; |
| interrupt-parent = <&intc>; |
| reg = < 0xf8891000 0x1000 0xf8893000 0x1000 >; |
| }; |
| |
| regulator_vccpint: fixedregulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "VCCPINT"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| amba: amba { |
| u-boot,dm-pre-reloc; |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| interrupt-parent = <&intc>; |
| ranges; |
| |
| adc: adc@f8007100 { |
| compatible = "xlnx,zynq-xadc-1.00.a"; |
| reg = <0xf8007100 0x20>; |
| interrupts = <0 7 4>; |
| interrupt-parent = <&intc>; |
| clocks = <&clkc 12>; |
| }; |
| |
| can0: can@e0008000 { |
| compatible = "xlnx,zynq-can-1.0"; |
| status = "disabled"; |
| clocks = <&clkc 19>, <&clkc 36>; |
| clock-names = "can_clk", "pclk"; |
| reg = <0xe0008000 0x1000>; |
| interrupts = <0 28 4>; |
| interrupt-parent = <&intc>; |
| tx-fifo-depth = <0x40>; |
| rx-fifo-depth = <0x40>; |
| }; |
| |
| can1: can@e0009000 { |
| compatible = "xlnx,zynq-can-1.0"; |
| status = "disabled"; |
| clocks = <&clkc 20>, <&clkc 37>; |
| clock-names = "can_clk", "pclk"; |
| reg = <0xe0009000 0x1000>; |
| interrupts = <0 51 4>; |
| interrupt-parent = <&intc>; |
| tx-fifo-depth = <0x40>; |
| rx-fifo-depth = <0x40>; |
| }; |
| |
| gpio0: gpio@e000a000 { |
| compatible = "xlnx,zynq-gpio-1.0"; |
| #gpio-cells = <2>; |
| clocks = <&clkc 42>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupt-parent = <&intc>; |
| interrupts = <0 20 4>; |
| reg = <0xe000a000 0x1000>; |
| }; |
| |
| i2c0: i2c@e0004000 { |
| compatible = "cdns,i2c-r1p10"; |
| status = "disabled"; |
| clocks = <&clkc 38>; |
| interrupt-parent = <&intc>; |
| interrupts = <0 25 4>; |
| reg = <0xe0004000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| i2c1: i2c@e0005000 { |
| compatible = "cdns,i2c-r1p10"; |
| status = "disabled"; |
| clocks = <&clkc 39>; |
| interrupt-parent = <&intc>; |
| interrupts = <0 48 4>; |
| reg = <0xe0005000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| intc: interrupt-controller@f8f01000 { |
| compatible = "arm,cortex-a9-gic"; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0xF8F01000 0x1000>, |
| <0xF8F00100 0x100>; |
| }; |
| |
| L2: cache-controller@f8f02000 { |
| compatible = "arm,pl310-cache"; |
| reg = <0xF8F02000 0x1000>; |
| interrupts = <0 2 4>; |
| arm,data-latency = <3 2 2>; |
| arm,tag-latency = <2 2 2>; |
| cache-unified; |
| cache-level = <2>; |
| }; |
| |
| mc: memory-controller@f8006000 { |
| compatible = "xlnx,zynq-ddrc-a05"; |
| reg = <0xf8006000 0x1000>; |
| }; |
| |
| uart0: serial@e0000000 { |
| compatible = "xlnx,xuartps", "cdns,uart-r1p8"; |
| status = "disabled"; |
| clocks = <&clkc 23>, <&clkc 40>; |
| clock-names = "uart_clk", "pclk"; |
| reg = <0xE0000000 0x1000>; |
| interrupts = <0 27 4>; |
| }; |
| |
| uart1: serial@e0001000 { |
| compatible = "xlnx,xuartps", "cdns,uart-r1p8"; |
| status = "disabled"; |
| clocks = <&clkc 24>, <&clkc 41>; |
| clock-names = "uart_clk", "pclk"; |
| reg = <0xE0001000 0x1000>; |
| interrupts = <0 50 4>; |
| }; |
| |
| spi0: spi@e0006000 { |
| compatible = "xlnx,zynq-spi-r1p6"; |
| reg = <0xe0006000 0x1000>; |
| status = "disabled"; |
| interrupt-parent = <&intc>; |
| interrupts = <0 26 4>; |
| clocks = <&clkc 25>, <&clkc 34>; |
| clock-names = "ref_clk", "pclk"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| spi1: spi@e0007000 { |
| compatible = "xlnx,zynq-spi-r1p6"; |
| reg = <0xe0007000 0x1000>; |
| status = "disabled"; |
| interrupt-parent = <&intc>; |
| interrupts = <0 49 4>; |
| clocks = <&clkc 26>, <&clkc 35>; |
| clock-names = "ref_clk", "pclk"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| qspi: spi@e000d000 { |
| clock-names = "ref_clk", "pclk"; |
| clocks = <&clkc 10>, <&clkc 43>; |
| compatible = "xlnx,zynq-qspi-1.0"; |
| status = "disabled"; |
| interrupt-parent = <&intc>; |
| interrupts = <0 19 4>; |
| reg = <0xe000d000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| gem0: ethernet@e000b000 { |
| compatible = "cdns,zynq-gem", "cdns,gem"; |
| reg = <0xe000b000 0x1000>; |
| status = "disabled"; |
| interrupts = <0 22 4>; |
| clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>; |
| clock-names = "pclk", "hclk", "tx_clk"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| gem1: ethernet@e000c000 { |
| compatible = "cdns,zynq-gem", "cdns,gem"; |
| reg = <0xe000c000 0x1000>; |
| status = "disabled"; |
| interrupts = <0 45 4>; |
| clocks = <&clkc 31>, <&clkc 31>, <&clkc 14>; |
| clock-names = "pclk", "hclk", "tx_clk"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| sdhci0: sdhci@e0100000 { |
| compatible = "arasan,sdhci-8.9a"; |
| status = "disabled"; |
| clock-names = "clk_xin", "clk_ahb"; |
| clocks = <&clkc 21>, <&clkc 32>; |
| interrupt-parent = <&intc>; |
| interrupts = <0 24 4>; |
| reg = <0xe0100000 0x1000>; |
| }; |
| |
| sdhci1: sdhci@e0101000 { |
| compatible = "arasan,sdhci-8.9a"; |
| status = "disabled"; |
| clock-names = "clk_xin", "clk_ahb"; |
| clocks = <&clkc 22>, <&clkc 33>; |
| interrupt-parent = <&intc>; |
| interrupts = <0 47 4>; |
| reg = <0xe0101000 0x1000>; |
| }; |
| |
| slcr: slcr@f8000000 { |
| u-boot,dm-pre-reloc; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "xlnx,zynq-slcr", "syscon", "simple-mfd"; |
| reg = <0xF8000000 0x1000>; |
| ranges; |
| clkc: clkc@100 { |
| u-boot,dm-pre-reloc; |
| #clock-cells = <1>; |
| compatible = "xlnx,ps7-clkc"; |
| fclk-enable = <0>; |
| clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x", |
| "cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x", |
| "dci", "lqspi", "smc", "pcap", "gem0", "gem1", |
| "fclk0", "fclk1", "fclk2", "fclk3", "can0", "can1", |
| "sdio0", "sdio1", "uart0", "uart1", "spi0", "spi1", |
| "dma", "usb0_aper", "usb1_aper", "gem0_aper", |
| "gem1_aper", "sdio0_aper", "sdio1_aper", |
| "spi0_aper", "spi1_aper", "can0_aper", "can1_aper", |
| "i2c0_aper", "i2c1_aper", "uart0_aper", "uart1_aper", |
| "gpio_aper", "lqspi_aper", "smc_aper", "swdt", |
| "dbg_trc", "dbg_apb"; |
| reg = <0x100 0x100>; |
| }; |
| |
| rstc: rstc@200 { |
| compatible = "xlnx,zynq-reset"; |
| reg = <0x200 0x48>; |
| #reset-cells = <1>; |
| syscon = <&slcr>; |
| }; |
| |
| pinctrl0: pinctrl@700 { |
| compatible = "xlnx,pinctrl-zynq"; |
| reg = <0x700 0x200>; |
| syscon = <&slcr>; |
| }; |
| }; |
| |
| dmac_s: dmac@f8003000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0xf8003000 0x1000>; |
| interrupt-parent = <&intc>; |
| interrupt-names = "abort", "dma0", "dma1", "dma2", "dma3", |
| "dma4", "dma5", "dma6", "dma7"; |
| interrupts = <0 13 4>, |
| <0 14 4>, <0 15 4>, |
| <0 16 4>, <0 17 4>, |
| <0 40 4>, <0 41 4>, |
| <0 42 4>, <0 43 4>; |
| #dma-cells = <1>; |
| #dma-channels = <8>; |
| #dma-requests = <4>; |
| clocks = <&clkc 27>; |
| clock-names = "apb_pclk"; |
| }; |
| |
| devcfg: devcfg@f8007000 { |
| compatible = "xlnx,zynq-devcfg-1.0"; |
| interrupt-parent = <&intc>; |
| interrupts = <0 8 4>; |
| reg = <0xf8007000 0x100>; |
| clocks = <&clkc 12>, <&clkc 15>, <&clkc 16>, <&clkc 17>, <&clkc 18>; |
| clock-names = "ref_clk", "fclk0", "fclk1", "fclk2", "fclk3"; |
| syscon = <&slcr>; |
| }; |
| |
| global_timer: timer@f8f00200 { |
| compatible = "arm,cortex-a9-global-timer"; |
| reg = <0xf8f00200 0x20>; |
| interrupts = <1 11 0x301>; |
| interrupt-parent = <&intc>; |
| clocks = <&clkc 4>; |
| }; |
| |
| ttc0: timer@f8001000 { |
| interrupt-parent = <&intc>; |
| interrupts = <0 10 4>, <0 11 4>, <0 12 4>; |
| compatible = "cdns,ttc"; |
| clocks = <&clkc 6>; |
| reg = <0xF8001000 0x1000>; |
| }; |
| |
| ttc1: timer@f8002000 { |
| interrupt-parent = <&intc>; |
| interrupts = <0 37 4>, <0 38 4>, <0 39 4>; |
| compatible = "cdns,ttc"; |
| clocks = <&clkc 6>; |
| reg = <0xF8002000 0x1000>; |
| }; |
| |
| scutimer: timer@f8f00600 { |
| interrupt-parent = <&intc>; |
| interrupts = <1 13 0x301>; |
| compatible = "arm,cortex-a9-twd-timer"; |
| reg = <0xf8f00600 0x20>; |
| clocks = <&clkc 4>; |
| }; |
| |
| usb0: usb@e0002000 { |
| compatible = "xlnx,zynq-usb-2.20a", "chipidea,usb2"; |
| status = "disabled"; |
| clocks = <&clkc 28>; |
| interrupt-parent = <&intc>; |
| interrupts = <0 21 4>; |
| reg = <0xe0002000 0x1000>; |
| phy_type = "ulpi"; |
| }; |
| |
| usb1: usb@e0003000 { |
| compatible = "xlnx,zynq-usb-2.20a", "chipidea,usb2"; |
| status = "disabled"; |
| clocks = <&clkc 29>; |
| interrupt-parent = <&intc>; |
| interrupts = <0 44 4>; |
| reg = <0xe0003000 0x1000>; |
| phy_type = "ulpi"; |
| }; |
| |
| watchdog0: watchdog@f8005000 { |
| clocks = <&clkc 45>; |
| compatible = "cdns,wdt-r1p2"; |
| interrupt-parent = <&intc>; |
| interrupts = <0 9 1>; |
| reg = <0xf8005000 0x1000>; |
| timeout-sec = <10>; |
| }; |
| }; |
| }; |