blob: 87624bf4220f90d6f5c35f681f7ac8dded7db8bb [file] [log] [blame]
/*
* NS16550 Serial Port
* originally from linux source (arch/ppc/boot/ns16550.h)
*
* Cleanup and unification
* (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
*
* modified slightly to
* have addresses as offsets from CONFIG_SYS_ISA_BASE
* added a few more definitions
* added prototypes for ns16550.c
* reduced no of com ports to 2
* modifications (c) Rob Taylor, Flying Pig Systems. 2000.
*
* added support for port on 64-bit bus
* by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems
*/
#if (CONFIG_SYS_NS16550_REG_SIZE == 1)
struct NS16550 {
unsigned char rbr; /* 0 */
unsigned char ier; /* 1 */
unsigned char fcr; /* 2 */
unsigned char lcr; /* 3 */
unsigned char mcr; /* 4 */
unsigned char lsr; /* 5 */
unsigned char msr; /* 6 */
unsigned char scr; /* 7 */
#if defined(CONFIG_OMAP730)
unsigned char mdr1; /* 8 */
unsigned char reg9; /* 9 */
unsigned char regA; /* A */
unsigned char regB; /* B */
unsigned char regC; /* C */
unsigned char regD; /* D */
unsigned char regE; /* E */
unsigned char regF; /* F */
unsigned char reg10; /* 10 */
unsigned char ssr; /* 11*/
#endif
} __attribute__ ((packed));
#elif (CONFIG_SYS_NS16550_REG_SIZE == 2)
struct NS16550 {
unsigned short rbr; /* 0 */
unsigned short ier; /* 1 */
unsigned short fcr; /* 2 */
unsigned short lcr; /* 3 */
unsigned short mcr; /* 4 */
unsigned short lsr; /* 5 */
unsigned short msr; /* 6 */
unsigned short scr; /* 7 */
} __attribute__ ((packed));
#elif (CONFIG_SYS_NS16550_REG_SIZE == 4)
struct NS16550 {
unsigned long rbr; /* 0 r */
unsigned long ier; /* 1 rw */
unsigned long fcr; /* 2 w */
unsigned long lcr; /* 3 rw */
unsigned long mcr; /* 4 rw */
unsigned long lsr; /* 5 r */
unsigned long msr; /* 6 r */
unsigned long scr; /* 7 rw */
}; /* No need to pack an already aligned struct */
#elif (CONFIG_SYS_NS16550_REG_SIZE == -4)
struct NS16550 {
unsigned char rbr; /* 0 */
int pad1:24;
unsigned char ier; /* 1 */
int pad2:24;
unsigned char fcr; /* 2 */
int pad3:24;
unsigned char lcr; /* 3 */
int pad4:24;
unsigned char mcr; /* 4 */
int pad5:24;
unsigned char lsr; /* 5 */
int pad6:24;
unsigned char msr; /* 6 */
int pad7:24;
unsigned char scr; /* 7 */
int pad8:24;
#if defined(CONFIG_OMAP)
unsigned char mdr1; /* mode select reset TL16C750*/
#endif
#ifdef CONFIG_OMAP1510
int pad9:24;
unsigned long pad[10];
unsigned char osc_12m_sel;
int pad10:24;
#endif
} __attribute__ ((packed));
#elif (CONFIG_SYS_NS16550_REG_SIZE == -8)
struct NS16550 {
unsigned char rbr; /* 0 */
unsigned char pad0[7];
unsigned char ier; /* 1 */
unsigned char pad1[7];
unsigned char fcr; /* 2 */
unsigned char pad2[7];
unsigned char lcr; /* 3 */
unsigned char pad3[7];
unsigned char mcr; /* 4 */
unsigned char pad4[7];
unsigned char lsr; /* 5 */
unsigned char pad5[7];
unsigned char msr; /* 6 */
unsigned char pad6[7];
unsigned char scr; /* 7 */
unsigned char pad7[7];
} __attribute__ ((packed));
#else
#error "Please define NS16550 registers size."
#endif
#define thr rbr
#define iir fcr
#define dll rbr
#define dlm ier
typedef volatile struct NS16550 *NS16550_t;
/*
* These are the definitions for the FIFO Control Register
*/
#define UART_FCR_FIFO_EN 0x01 /* Fifo enable */
#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
#define UART_FCR_RXSR 0x02 /* Receiver soft reset */
#define UART_FCR_TXSR 0x04 /* Transmitter soft reset */
/*
* These are the definitions for the Modem Control Register
*/
#define UART_MCR_DTR 0x01 /* DTR */
#define UART_MCR_RTS 0x02 /* RTS */
#define UART_MCR_OUT1 0x04 /* Out 1 */
#define UART_MCR_OUT2 0x08 /* Out 2 */
#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
#define UART_MCR_DMA_EN 0x04
#define UART_MCR_TX_DFR 0x08
/*
* These are the definitions for the Line Control Register
*
* Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
* UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
*/
#define UART_LCR_WLS_MSK 0x03 /* character length select mask */
#define UART_LCR_WLS_5 0x00 /* 5 bit character length */
#define UART_LCR_WLS_6 0x01 /* 6 bit character length */
#define UART_LCR_WLS_7 0x02 /* 7 bit character length */
#define UART_LCR_WLS_8 0x03 /* 8 bit character length */
#define UART_LCR_STB 0x04 /* Number of stop Bits, off = 1, on = 1.5 or 2) */
#define UART_LCR_PEN 0x08 /* Parity eneble */
#define UART_LCR_EPS 0x10 /* Even Parity Select */
#define UART_LCR_STKP 0x20 /* Stick Parity */
#define UART_LCR_SBRK 0x40 /* Set Break */
#define UART_LCR_BKSE 0x80 /* Bank select enable */
#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
/*
* These are the definitions for the Line Status Register
*/
#define UART_LSR_DR 0x01 /* Data ready */
#define UART_LSR_OE 0x02 /* Overrun */
#define UART_LSR_PE 0x04 /* Parity error */
#define UART_LSR_FE 0x08 /* Framing error */
#define UART_LSR_BI 0x10 /* Break */
#define UART_LSR_THRE 0x20 /* Xmit holding register empty */
#define UART_LSR_TEMT 0x40 /* Xmitter empty */
#define UART_LSR_ERR 0x80 /* Error */
#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
#define UART_MSR_RI 0x40 /* Ring Indicator */
#define UART_MSR_DSR 0x20 /* Data Set Ready */
#define UART_MSR_CTS 0x10 /* Clear to Send */
#define UART_MSR_DDCD 0x08 /* Delta DCD */
#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
#define UART_MSR_DDSR 0x02 /* Delta DSR */
#define UART_MSR_DCTS 0x01 /* Delta CTS */
/*
* These are the definitions for the Interrupt Identification Register
*/
#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
#define UART_IIR_MSI 0x00 /* Modem status interrupt */
#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
/*
* These are the definitions for the Interrupt Enable Register
*/
#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
#ifdef CONFIG_OMAP1510
#define OSC_12M_SEL 0x01 /* selects 6.5 * current clk div */
#endif
/* useful defaults for LCR */
#define UART_LCR_8N1 0x03
void NS16550_init (NS16550_t com_port, int baud_divisor);
void NS16550_putc (NS16550_t com_port, char c);
char NS16550_getc (NS16550_t com_port);
int NS16550_tstc (NS16550_t com_port);
void NS16550_reinit (NS16550_t com_port, int baud_divisor);