include/configs/ERIC.h - platform/external/u-boot - Gitiles

 /*
  * (C) Copyright 2001
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */

 /*
  * board/config.h - configuration options, board specific
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
 #define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_ERIC		1	/* ...on a ERIC board	*/

 #define	CONFIG_BOARD_EARLY_INIT_F 1	/* run board_early_init_f() */

 #define CONFIG_SYS_CLK_FREQ	33333333 /* external frequency to pll	*/

 #if 1
 #define CFG_ENV_IS_IN_FLASH	1	/* use FLASH for environment vars	*/
 #endif
 #if 0
 #define CONFIG_ENV_IS_IN_NVRAM	1	/* use NVRAM for environment vars	*/
 #endif
 #if 0
 #define CONFIG_ENV_IS_IN_EEPROM	1	/* use I2C RTC X1240 for environment vars */
 #define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
 #define CFG_ENV_SIZE		0x800	/* 2048 bytes may be used for env vars */
 #endif					/* total size of a X1240 is 2048 bytes */

 #define CONFIG_HARD_I2C		1	/* I2C with hardware support */
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CFG_I2C_SLAVE		0x7F

 #define CFG_I2C_EEPROM_ADDR	0x57	/* X1240 has two I2C slave addresses, one for EEPROM */
 #define CFG_I2C_EEPROM_ADDR_LEN	2	/* address length for the eeprom */
 #define CONFIG_I2C_RTC		1	/* we have a Xicor X1240 RTC */
 #define CFG_I2C_RTC_ADDR	0x6F	/*                                and one for RTC */

 #ifdef CFG_ENV_IS_IN_FLASH
 #undef CONFIG_ENV_IS_IN_NVRAM
 #undef CONFIG_ENV_IS_IN_EEPROM
 #else
 #ifdef CONFIG_ENV_IS_IN_NVRAM
 #undef CFG_ENV_IS_IN_FLASH
 #undef CONFIG_ENV_IS_IN_EEPROM
 #else
 #ifdef CONFIG_ENV_IS_IN_EEPROM
 #undef CONFIG_ENV_IS_IN_NVRAM
 #undef CFG_ENV_IS_IN_FLASH
 #endif
 #endif
 #endif

 #define CONFIG_BAUDRATE		115200
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/

 #if 1
 #define CONFIG_BOOTCOMMAND	"bootm ffc00000" /* autoboot command	*/
 #else
 #define CONFIG_BOOTCOMMAND	"bootp" /* autoboot command		*/
 #endif

 #define CONFIG_BOOTARGS		"console=ttyS0,115200 root=/dev/nfs "	\
 				"nfsroot=192.168.1.2:/eric_root_devel "	\
 				"ip=192.168.1.22:192.168.1.2"

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/

 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address			*/


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_ENV
 #define CONFIG_CMD_FLASH


 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/

 /*
  * Miscellaneous configurable options
  */
 #undef	CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

 #define	 CFG_EXT_SERIAL_CLOCK	 14318180

 /* The following table includes the supported baudrates */
 #define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }

 #define CFG_LOAD_ADDR		0x100000	/* default load address */
 #define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */

 #define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */

 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
  */
 #define PCI_HOST_ADAPTER 0              /* configure ar pci adapter     */
 #define PCI_HOST_FORCE  1               /* configure as pci host        */
 #define PCI_HOST_AUTO   2               /* detected via arbiter enable  */

 #define CONFIG_PCI			/* include pci support	        */
 #define CONFIG_PCI_HOST	PCI_HOST_FORCE  /* select pci host function     */
 #undef  CONFIG_PCI_PNP			/* no pci plug-and-play         */
 					/* resource configuration       */

 #define CFG_PCI_SUBSYS_VENDORID 0x1743	/* PCI Vendor ID: Peppercon AG	*/
 #define CFG_PCI_SUBSYS_DEVICEID 0x0405	/* PCI Device ID: 405GP		*/
 #define CFG_PCI_PTM1LA	0xFFFC0000	/* point to flash		*/
 #define CFG_PCI_PTM1MS	0xFFFFF001	/* 4kB, enable hard-wired to 1	*/
 #define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
 #define CFG_PCI_PTM2LA	0x00000000	/* disabled			*/
 #define CFG_PCI_PTM2MS	0x00000000	/* disabled			*/
 #define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */

 /*-----------------------------------------------------------------------
  * External peripheral base address
  *-----------------------------------------------------------------------
  */
 /*	Bank 0 - Flash/SRAM	       0xFF000000 16MB	16 Bit */
 /*	Bank 1 - NVRAM/RTC	       0xF0000000  1MB	 8 Bit */
 /*	Bank 2 - A/D converter	       0xF0100000  1MB	 8 Bit */
 /*	Bank 3 - Ethernet PHY Reset    0xF0200000  1MB	 8 Bit */
 /*	Bank 4 - PC-MIP PRSNT1#	       0xF0300000  1MB	 8 Bit */
 /*	Bank 5 - PC-MIP PRSNT2#	       0xF0400000  1MB	 8 Bit */
 /*	Bank 6 - CPU LED0	       0xF0500000  1MB	 8 Bit */
 /*	Bank 7 - CPU LED1	       0xF0600000  1MB	 8 Bit */

 /* ----------------------------------------------------------------------- */
 /*  Memory Bank 0 (Flash) initialization */
 /* ----------------------------------------------------------------------- */
 #define CS0_AP	0x9B015480
 #define CS0_CR	0xFF87A000 /*  BAS=0xFF8,BS=(8MB),BU=0x3(R/W), BW=(16 bits) */
 /* ----------------------------------------------------------------------- */
 /*  Memory Bank 1 (NVRAM/RTC) initialization */
 /* ----------------------------------------------------------------------- */
 #define CS1_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
 #define CS1_CR	0xF0018000 /* BAS=0xF00,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
  /* ----------------------------------------------------------------------- */
  /*  Memory Bank 2 (A/D converter) initialization */
  /* ----------------------------------------------------------------------- */
 #define CS2_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
 #define CS2_CR	0xF0118000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
 /* ----------------------------------------------------------------------- */
 /*  Memory Bank 3 (Ethernet PHY Reset) initialization */
 /* ----------------------------------------------------------------------- */
 #define CS3_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
 #define CS3_CR	0xF0218000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
 /* ----------------------------------------------------------------------- */
 /*  Memory Bank 4 (PC-MIP PRSNT1#) initialization */
 /* ----------------------------------------------------------------------- */
 #define CS4_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
 #define CS4_CR	0xF0318000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
 /* ----------------------------------------------------------------------- */
 /*  Memory Bank 5 (PC-MIP PRSNT2#) initialization */
 /* ----------------------------------------------------------------------- */
 #define CS5_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
 #define CS5_CR	0xF0418000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
 /* ----------------------------------------------------------------------- */
 /*  Memory Bank 6 (CPU LED0) initialization */
 /* ----------------------------------------------------------------------- */
 #define CS6_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
 #define CS6_CR	0xF0518000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
 /* ----------------------------------------------------------------------- */
 /*  Memory Bank 7 (CPU LED1) initialization */
 /* ----------------------------------------------------------------------- */
 #define CS7_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
 #define CS7_CR	0xF0618000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */

 #define CFG_NVRAM_REG_BASE_ADDR	 0xF0000000
 #define CFG_RTC_REG_BASE_ADDR	 (0xF0000000 + 0x7F8)
 #define CFG_ADC_REG_BASE_ADDR	 0xF0100000
 #define CFG_PHYRES_REG_BASE_ADDR 0xF0200000
 #define CFG_PRSNT1_REG_BASE_ADDR 0xF0300000
 #define CFG_PRSNT2_REG_BASE_ADDR 0xF0400000
 #define CFG_LED0_REG_BASE_ADDR	 0xF0500000
 #define CFG_LED1_REG_BASE_ADDR	 0xF0600000


 /*  SDRAM CONFIG */
 #define CFG_SDRAM_MANUALLY    1
 #define CFG_SDRAM_SINGLE_BANK 1

 #ifdef CFG_SDRAM_MANUALLY
 /*-----------------------------------------------------------------------
  * Set MB0CF for bank 0. (0-32MB) Address Mode 4 since 12x8(2)
  *----------------------------------------------------------------------*/
 #define MB0CF	0x00062001 /*  32MB @ 0 */
 /*-----------------------------------------------------------------------
  * Set MB1CF for bank 1. (32MB-64MB) Address Mode 4 since 12x8(2)
  *----------------------------------------------------------------------*/
 #ifdef CFG_SDRAM_SINGLE_BANK
 #define MB1CF	0x0 /*  0MB @ 32MB */
 #else
 #define MB1CF	0x02062001 /*  32MB @ 32MB */
 #endif
 /*-----------------------------------------------------------------------
  * Set MB2CF for bank 2. off
  *----------------------------------------------------------------------*/
 #define MB2CF	0x0 /*  0MB */
 /*-----------------------------------------------------------------------
  * Set MB3CF for bank 3. off
  *----------------------------------------------------------------------*/
 #define MB3CF	0x0 /*  0MB */

 #define SDTR_100    0x0086400D
 #define RTR_100     0x05F0
 #define SDTR_66     0x00854006	/* orig U-Boot-wallnut says 0x00854006 */
 #define RTR_66      0x03f8

 #endif   /* CFG_SDRAM_MANUALLY */


 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
 #define CFG_SDRAM_SIZE		32
 #define CFG_FLASH_BASE		0xFF800000      /* 8 MByte Flash */
 #define CFG_MONITOR_BASE	0xFFFE0000      /* last 128kByte within Flash */
 /*#define CFG_MONITOR_LEN		(192 * 1024)*/	/* Reserve 196 kB for Monitor	*/
 #define CFG_MONITOR_LEN		(128 * 1024)	/* Reserve 128 kB for Monitor	*/
 #define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
 #define CFG_MAX_FLASH_SECT	64	/* max number of sectors on one chip	*/
 #define CFG_FLASH_16BIT		1	/* Rom 16 bit data bus			*/

 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

 /* BEG ENVIRONNEMENT FLASH */
 #ifdef CFG_ENV_IS_IN_FLASH
 #define CFG_ENV_SECT_SIZE       (128*1024)

 #if 0  /* force ENV to be NOT embedded */
 #define CFG_ENV_ADDR            0xfffa0000
 #else  /* force ENV to be embedded */
 #define	CFG_ENV_SIZE		(2 * 1024) /* Total Size of Environment Sector 2k */
 #define CFG_ENV_ADDR            (CFG_MONITOR_BASE + CFG_MONITOR_LEN - CFG_ENV_SIZE - 0x10) /* let space for reset vector */
 /* #define CFG_ENV_ADDR            (CFG_MONITOR_BASE)*/
 #define CFG_ENV_OFFSET          (CFG_ENV_ADDR - CFG_FLASH_BASE)
 #endif

 #endif
 /* END ENVIRONNEMENT FLASH */
 /*-----------------------------------------------------------------------
  * NVRAM organization
  */
 #define CFG_NVRAM_BASE_ADDR	CFG_NVRAM_REG_BASE_ADDR	/* NVRAM base address	*/
 #define CFG_NVRAM_SIZE		0x7F8		/* NVRAM size 2kByte - 8 Byte for RTC */

 #ifdef CONFIG_ENV_IS_IN_NVRAM
 #define CFG_ENV_SIZE		0x7F8		/* Size of Environment vars	*/
 #define CFG_ENV_ADDR		\
 	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)	/* Env	*/
 #endif

 /*
  * Init Memory Controller:
  *
  * BR0/1 and OR0/1 (FLASH)
  */

 #define FLASH_BASE0_PRELIM	0xFF800000	/* FLASH bank #0 8MB	*/
 #define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/


 /* Configuration Port location */
 /*  #define CONFIG_PORT_ADDR	0xF0000500 */

 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CFG_INIT_RAM_ADDR	0x00df0000  /* inside of SDRAM		       */
 #define CFG_INIT_RAM_END	0x0f00	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET

 /*-----------------------------------------------------------------------
  * Definitions for Serial Presence Detect EEPROM address
  * (to get SDRAM settings)
  */
 #define SPD_EEPROM_ADDRESS      0x50

 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 #endif	/* __CONFIG_H */
	/*
	* (C) Copyright 2001
	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/

	/*
	* board/config.h - configuration options, board specific
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_405GP 1 /* This is a PPC405 CPU */
	#define CONFIG_4xx 1 /* ...member of PPC4xx family */
	#define CONFIG_ERIC 1 /* ...on a ERIC board */

	#define CONFIG_BOARD_EARLY_INIT_F 1 /* run board_early_init_f() */

	#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */

	#if 1
	#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
	#endif
	#if 0
	#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
	#endif
	#if 0
	#define CONFIG_ENV_IS_IN_EEPROM 1 /* use I2C RTC X1240 for environment vars */
	#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
	#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars */
	#endif /* total size of a X1240 is 2048 bytes */

	#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
	#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
	#define CFG_I2C_SLAVE 0x7F

	#define CFG_I2C_EEPROM_ADDR 0x57 /* X1240 has two I2C slave addresses, one for EEPROM */
	#define CFG_I2C_EEPROM_ADDR_LEN 2 /* address length for the eeprom */
	#define CONFIG_I2C_RTC 1 /* we have a Xicor X1240 RTC */
	#define CFG_I2C_RTC_ADDR 0x6F /* and one for RTC */

	#ifdef CFG_ENV_IS_IN_FLASH
	#undef CONFIG_ENV_IS_IN_NVRAM
	#undef CONFIG_ENV_IS_IN_EEPROM
	#else
	#ifdef CONFIG_ENV_IS_IN_NVRAM
	#undef CFG_ENV_IS_IN_FLASH
	#undef CONFIG_ENV_IS_IN_EEPROM
	#else
	#ifdef CONFIG_ENV_IS_IN_EEPROM
	#undef CONFIG_ENV_IS_IN_NVRAM
	#undef CFG_ENV_IS_IN_FLASH
	#endif
	#endif
	#endif

	#define CONFIG_BAUDRATE 115200
	#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */

	#if 1
	#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */
	#else
	#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
	#endif

	#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/nfs " \
	"nfsroot=192.168.1.2:/eric_root_devel " \
	"ip=192.168.1.22:192.168.1.2"

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	#define CONFIG_MII 1 /* MII PHY management */
	#define CONFIG_PHY_ADDR 1 /* PHY address */


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_PCI
	#define CONFIG_CMD_IRQ
	#define CONFIG_CMD_ENV
	#define CONFIG_CMD_FLASH


	#undef CONFIG_WATCHDOG /* watchdog disabled */

	/*
	* Miscellaneous configurable options
	*/
	#undef CFG_LONGHELP /* undef to save memory */
	#define CFG_PROMPT "=> " /* Monitor Command Prompt */
	#if defined(CONFIG_CMD_KGDB)
	#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
	#define CFG_MAXARGS 16 /* max number of command args */
	#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */

	#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
	#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */

	#define CFG_EXT_SERIAL_CLOCK 14318180

	/* The following table includes the supported baudrates */
	#define CFG_BAUDRATE_TABLE \
	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
	57600, 115200, 230400, 460800, 921600 }

	#define CFG_LOAD_ADDR 0x100000 /* default load address */
	#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */

	#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */

	/*-----------------------------------------------------------------------
	* PCI stuff
	*-----------------------------------------------------------------------
	*/
	#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
	#define PCI_HOST_FORCE 1 /* configure as pci host */
	#define PCI_HOST_AUTO 2 /* detected via arbiter enable */

	#define CONFIG_PCI /* include pci support */
	#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
	#undef CONFIG_PCI_PNP /* no pci plug-and-play */
	/* resource configuration */

	#define CFG_PCI_SUBSYS_VENDORID 0x1743 /* PCI Vendor ID: Peppercon AG */
	#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: 405GP */
	#define CFG_PCI_PTM1LA 0xFFFC0000 /* point to flash */
	#define CFG_PCI_PTM1MS 0xFFFFF001 /* 4kB, enable hard-wired to 1 */
	#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
	#define CFG_PCI_PTM2LA 0x00000000 /* disabled */
	#define CFG_PCI_PTM2MS 0x00000000 /* disabled */
	#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */

	/*-----------------------------------------------------------------------
	* External peripheral base address
	*-----------------------------------------------------------------------
	*/
	/* Bank 0 - Flash/SRAM 0xFF000000 16MB 16 Bit */
	/* Bank 1 - NVRAM/RTC 0xF0000000 1MB 8 Bit */
	/* Bank 2 - A/D converter 0xF0100000 1MB 8 Bit */
	/* Bank 3 - Ethernet PHY Reset 0xF0200000 1MB 8 Bit */
	/* Bank 4 - PC-MIP PRSNT1# 0xF0300000 1MB 8 Bit */
	/* Bank 5 - PC-MIP PRSNT2# 0xF0400000 1MB 8 Bit */
	/* Bank 6 - CPU LED0 0xF0500000 1MB 8 Bit */
	/* Bank 7 - CPU LED1 0xF0600000 1MB 8 Bit */

	/* ----------------------------------------------------------------------- */
	/* Memory Bank 0 (Flash) initialization */
	/* ----------------------------------------------------------------------- */
	#define CS0_AP 0x9B015480
	#define CS0_CR 0xFF87A000 /* BAS=0xFF8,BS=(8MB),BU=0x3(R/W), BW=(16 bits) */
	/* ----------------------------------------------------------------------- */
	/* Memory Bank 1 (NVRAM/RTC) initialization */
	/* ----------------------------------------------------------------------- */
	#define CS1_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
	#define CS1_CR 0xF0018000 /* BAS=0xF00,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
	/* ----------------------------------------------------------------------- */
	/* Memory Bank 2 (A/D converter) initialization */
	/* ----------------------------------------------------------------------- */
	#define CS2_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
	#define CS2_CR 0xF0118000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
	/* ----------------------------------------------------------------------- */
	/* Memory Bank 3 (Ethernet PHY Reset) initialization */
	/* ----------------------------------------------------------------------- */
	#define CS3_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
	#define CS3_CR 0xF0218000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
	/* ----------------------------------------------------------------------- */
	/* Memory Bank 4 (PC-MIP PRSNT1#) initialization */
	/* ----------------------------------------------------------------------- */
	#define CS4_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
	#define CS4_CR 0xF0318000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
	/* ----------------------------------------------------------------------- */
	/* Memory Bank 5 (PC-MIP PRSNT2#) initialization */
	/* ----------------------------------------------------------------------- */
	#define CS5_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
	#define CS5_CR 0xF0418000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
	/* ----------------------------------------------------------------------- */
	/* Memory Bank 6 (CPU LED0) initialization */
	/* ----------------------------------------------------------------------- */
	#define CS6_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
	#define CS6_CR 0xF0518000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
	/* ----------------------------------------------------------------------- */
	/* Memory Bank 7 (CPU LED1) initialization */
	/* ----------------------------------------------------------------------- */
	#define CS7_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
	#define CS7_CR 0xF0618000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */

	#define CFG_NVRAM_REG_BASE_ADDR 0xF0000000
	#define CFG_RTC_REG_BASE_ADDR (0xF0000000 + 0x7F8)
	#define CFG_ADC_REG_BASE_ADDR 0xF0100000
	#define CFG_PHYRES_REG_BASE_ADDR 0xF0200000
	#define CFG_PRSNT1_REG_BASE_ADDR 0xF0300000
	#define CFG_PRSNT2_REG_BASE_ADDR 0xF0400000
	#define CFG_LED0_REG_BASE_ADDR 0xF0500000
	#define CFG_LED1_REG_BASE_ADDR 0xF0600000


	/* SDRAM CONFIG */
	#define CFG_SDRAM_MANUALLY 1
	#define CFG_SDRAM_SINGLE_BANK 1

	#ifdef CFG_SDRAM_MANUALLY
	/*-----------------------------------------------------------------------
	* Set MB0CF for bank 0. (0-32MB) Address Mode 4 since 12x8(2)
	----------------------------------------------------------------------/
	#define MB0CF 0x00062001 /* 32MB @ 0 */
	/*-----------------------------------------------------------------------
	* Set MB1CF for bank 1. (32MB-64MB) Address Mode 4 since 12x8(2)
	----------------------------------------------------------------------/
	#ifdef CFG_SDRAM_SINGLE_BANK
	#define MB1CF 0x0 /* 0MB @ 32MB */
	#else
	#define MB1CF 0x02062001 /* 32MB @ 32MB */
	#endif
	/*-----------------------------------------------------------------------
	* Set MB2CF for bank 2. off
	----------------------------------------------------------------------/
	#define MB2CF 0x0 /* 0MB */
	/*-----------------------------------------------------------------------
	* Set MB3CF for bank 3. off
	----------------------------------------------------------------------/
	#define MB3CF 0x0 /* 0MB */

	#define SDTR_100 0x0086400D
	#define RTR_100 0x05F0
	#define SDTR_66 0x00854006 /* orig U-Boot-wallnut says 0x00854006 */
	#define RTR_66 0x03f8

	#endif /* CFG_SDRAM_MANUALLY */


	/*-----------------------------------------------------------------------
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CFG_SDRAM_BASE _must_ start at 0
	*/
	#define CFG_SDRAM_BASE 0x00000000
	#define CFG_SDRAM_SIZE 32
	#define CFG_FLASH_BASE 0xFF800000 /* 8 MByte Flash */
	#define CFG_MONITOR_BASE 0xFFFE0000 /* last 128kByte within Flash */
	/#define CFG_MONITOR_LEN (192 1024)/ / Reserve 196 kB for Monitor */
	#define CFG_MONITOR_LEN (128 * 1024) /* Reserve 128 kB for Monitor */
	#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
	/*-----------------------------------------------------------------------
	* FLASH organization
	*/
	#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
	#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
	#define CFG_FLASH_16BIT 1 /* Rom 16 bit data bus */

	#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
	#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */

	/* BEG ENVIRONNEMENT FLASH */
	#ifdef CFG_ENV_IS_IN_FLASH
	#define CFG_ENV_SECT_SIZE (128*1024)

	#if 0 /* force ENV to be NOT embedded */
	#define CFG_ENV_ADDR 0xfffa0000
	#else /* force ENV to be embedded */
	#define CFG_ENV_SIZE (2 * 1024) /* Total Size of Environment Sector 2k */
	#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN - CFG_ENV_SIZE - 0x10) /* let space for reset vector */
	/* #define CFG_ENV_ADDR (CFG_MONITOR_BASE)*/
	#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
	#endif

	#endif
	/* END ENVIRONNEMENT FLASH */
	/*-----------------------------------------------------------------------
	* NVRAM organization
	*/
	#define CFG_NVRAM_BASE_ADDR CFG_NVRAM_REG_BASE_ADDR /* NVRAM base address */
	#define CFG_NVRAM_SIZE 0x7F8 /* NVRAM size 2kByte - 8 Byte for RTC */

	#ifdef CONFIG_ENV_IS_IN_NVRAM
	#define CFG_ENV_SIZE 0x7F8 /* Size of Environment vars */
	#define CFG_ENV_ADDR \
	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */
	#endif

	/*
	* Init Memory Controller:
	*
	* BR0/1 and OR0/1 (FLASH)
	*/

	#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 8MB */
	#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */


	/* Configuration Port location */
	/* #define CONFIG_PORT_ADDR 0xF0000500 */

	/*-----------------------------------------------------------------------
	* Definitions for initial stack pointer and data area (in DPRAM)
	*/
	#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
	#define CFG_INIT_RAM_END 0x0f00 /* End of used area in RAM */
	#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
	#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
	#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET

	/*-----------------------------------------------------------------------
	* Definitions for Serial Presence Detect EEPROM address
	* (to get SDRAM settings)
	*/
	#define SPD_EEPROM_ADDRESS 0x50

	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
	#endif
	#endif /* __CONFIG_H */