| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2012 Altera Corporation <www.altera.com> |
| */ |
| |
| #include <common.h> |
| #include <asm/io.h> |
| #include <asm/pl310.h> |
| #include <asm/u-boot.h> |
| #include <asm/utils.h> |
| #include <image.h> |
| #include <asm/arch/reset_manager.h> |
| #include <spl.h> |
| #include <asm/arch/system_manager.h> |
| #include <asm/arch/freeze_controller.h> |
| #include <asm/arch/clock_manager.h> |
| #include <asm/arch/scan_manager.h> |
| #include <asm/arch/sdram.h> |
| #include <asm/arch/scu.h> |
| #include <asm/arch/nic301.h> |
| #include <asm/sections.h> |
| #include <fdtdec.h> |
| #include <watchdog.h> |
| #include <asm/arch/pinmux.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| static const struct socfpga_system_manager *sysmgr_regs = |
| (struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS; |
| |
| u32 spl_boot_device(void) |
| { |
| const u32 bsel = readl(&sysmgr_regs->bootinfo); |
| |
| switch (SYSMGR_GET_BOOTINFO_BSEL(bsel)) { |
| case 0x1: /* FPGA (HPS2FPGA Bridge) */ |
| return BOOT_DEVICE_RAM; |
| case 0x2: /* NAND Flash (1.8V) */ |
| case 0x3: /* NAND Flash (3.0V) */ |
| socfpga_per_reset(SOCFPGA_RESET(NAND), 0); |
| return BOOT_DEVICE_NAND; |
| case 0x4: /* SD/MMC External Transceiver (1.8V) */ |
| case 0x5: /* SD/MMC Internal Transceiver (3.0V) */ |
| socfpga_per_reset(SOCFPGA_RESET(SDMMC), 0); |
| socfpga_per_reset(SOCFPGA_RESET(DMA), 0); |
| return BOOT_DEVICE_MMC1; |
| case 0x6: /* QSPI Flash (1.8V) */ |
| case 0x7: /* QSPI Flash (3.0V) */ |
| socfpga_per_reset(SOCFPGA_RESET(QSPI), 0); |
| return BOOT_DEVICE_SPI; |
| default: |
| printf("Invalid boot device (bsel=%08x)!\n", bsel); |
| hang(); |
| } |
| } |
| |
| #ifdef CONFIG_SPL_MMC_SUPPORT |
| u32 spl_boot_mode(const u32 boot_device) |
| { |
| #if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT) |
| return MMCSD_MODE_FS; |
| #else |
| return MMCSD_MODE_RAW; |
| #endif |
| } |
| #endif |
| |
| void spl_board_init(void) |
| { |
| /* configuring the clock based on handoff */ |
| cm_basic_init(gd->fdt_blob); |
| WATCHDOG_RESET(); |
| |
| config_dedicated_pins(gd->fdt_blob); |
| WATCHDOG_RESET(); |
| |
| /* Release UART from reset */ |
| socfpga_reset_uart(0); |
| |
| /* enable console uart printing */ |
| preloader_console_init(); |
| } |
| |
| void board_init_f(ulong dummy) |
| { |
| /* |
| * Configure Clock Manager to use intosc clock instead external osc to |
| * ensure success watchdog operation. We do it as early as possible. |
| */ |
| cm_use_intosc(); |
| |
| socfpga_watchdog_disable(); |
| |
| arch_early_init_r(); |
| |
| #ifdef CONFIG_HW_WATCHDOG |
| /* release osc1 watchdog timer 0 from reset */ |
| socfpga_reset_deassert_osc1wd0(); |
| |
| /* reconfigure and enable the watchdog */ |
| hw_watchdog_init(); |
| WATCHDOG_RESET(); |
| #endif /* CONFIG_HW_WATCHDOG */ |
| } |