| /* |
| * Copyright (C) 2005-2006 Atmel Corporation |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| #include <common.h> |
| #include <clk.h> |
| #include <dm.h> |
| |
| /* |
| * The u-boot networking stack is a little weird. It seems like the |
| * networking core allocates receive buffers up front without any |
| * regard to the hardware that's supposed to actually receive those |
| * packets. |
| * |
| * The MACB receives packets into 128-byte receive buffers, so the |
| * buffers allocated by the core isn't very practical to use. We'll |
| * allocate our own, but we need one such buffer in case a packet |
| * wraps around the DMA ring so that we have to copy it. |
| * |
| * Therefore, define CONFIG_SYS_RX_ETH_BUFFER to 1 in the board-specific |
| * configuration header. This way, the core allocates one RX buffer |
| * and one TX buffer, each of which can hold a ethernet packet of |
| * maximum size. |
| * |
| * For some reason, the networking core unconditionally specifies a |
| * 32-byte packet "alignment" (which really should be called |
| * "padding"). MACB shouldn't need that, but we'll refrain from any |
| * core modifications here... |
| */ |
| |
| #include <net.h> |
| #ifndef CONFIG_DM_ETH |
| #include <netdev.h> |
| #endif |
| #include <malloc.h> |
| #include <miiphy.h> |
| |
| #include <linux/mii.h> |
| #include <asm/io.h> |
| #include <asm/dma-mapping.h> |
| #include <asm/arch/clk.h> |
| #include <linux/errno.h> |
| |
| #include "macb.h" |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #define MACB_RX_BUFFER_SIZE 4096 |
| #define MACB_RX_RING_SIZE (MACB_RX_BUFFER_SIZE / 128) |
| #define MACB_TX_RING_SIZE 16 |
| #define MACB_TX_TIMEOUT 1000 |
| #define MACB_AUTONEG_TIMEOUT 5000000 |
| |
| #ifdef CONFIG_MACB_ZYNQ |
| /* INCR4 AHB bursts */ |
| #define MACB_ZYNQ_GEM_DMACR_BLENGTH 0x00000004 |
| /* Use full configured addressable space (8 Kb) */ |
| #define MACB_ZYNQ_GEM_DMACR_RXSIZE 0x00000300 |
| /* Use full configured addressable space (4 Kb) */ |
| #define MACB_ZYNQ_GEM_DMACR_TXSIZE 0x00000400 |
| /* Set RXBUF with use of 128 byte */ |
| #define MACB_ZYNQ_GEM_DMACR_RXBUF 0x00020000 |
| #define MACB_ZYNQ_GEM_DMACR_INIT \ |
| (MACB_ZYNQ_GEM_DMACR_BLENGTH | \ |
| MACB_ZYNQ_GEM_DMACR_RXSIZE | \ |
| MACB_ZYNQ_GEM_DMACR_TXSIZE | \ |
| MACB_ZYNQ_GEM_DMACR_RXBUF) |
| #endif |
| |
| struct macb_dma_desc { |
| u32 addr; |
| u32 ctrl; |
| }; |
| |
| #define DMA_DESC_BYTES(n) (n * sizeof(struct macb_dma_desc)) |
| #define MACB_TX_DMA_DESC_SIZE (DMA_DESC_BYTES(MACB_TX_RING_SIZE)) |
| #define MACB_RX_DMA_DESC_SIZE (DMA_DESC_BYTES(MACB_RX_RING_SIZE)) |
| #define MACB_TX_DUMMY_DMA_DESC_SIZE (DMA_DESC_BYTES(1)) |
| |
| #define RXADDR_USED 0x00000001 |
| #define RXADDR_WRAP 0x00000002 |
| |
| #define RXBUF_FRMLEN_MASK 0x00000fff |
| #define RXBUF_FRAME_START 0x00004000 |
| #define RXBUF_FRAME_END 0x00008000 |
| #define RXBUF_TYPEID_MATCH 0x00400000 |
| #define RXBUF_ADDR4_MATCH 0x00800000 |
| #define RXBUF_ADDR3_MATCH 0x01000000 |
| #define RXBUF_ADDR2_MATCH 0x02000000 |
| #define RXBUF_ADDR1_MATCH 0x04000000 |
| #define RXBUF_BROADCAST 0x80000000 |
| |
| #define TXBUF_FRMLEN_MASK 0x000007ff |
| #define TXBUF_FRAME_END 0x00008000 |
| #define TXBUF_NOCRC 0x00010000 |
| #define TXBUF_EXHAUSTED 0x08000000 |
| #define TXBUF_UNDERRUN 0x10000000 |
| #define TXBUF_MAXRETRY 0x20000000 |
| #define TXBUF_WRAP 0x40000000 |
| #define TXBUF_USED 0x80000000 |
| |
| struct macb_device { |
| void *regs; |
| |
| unsigned int rx_tail; |
| unsigned int tx_head; |
| unsigned int tx_tail; |
| unsigned int next_rx_tail; |
| bool wrapped; |
| |
| void *rx_buffer; |
| void *tx_buffer; |
| struct macb_dma_desc *rx_ring; |
| struct macb_dma_desc *tx_ring; |
| |
| unsigned long rx_buffer_dma; |
| unsigned long rx_ring_dma; |
| unsigned long tx_ring_dma; |
| |
| struct macb_dma_desc *dummy_desc; |
| unsigned long dummy_desc_dma; |
| |
| const struct device *dev; |
| #ifndef CONFIG_DM_ETH |
| struct eth_device netdev; |
| #endif |
| unsigned short phy_addr; |
| struct mii_dev *bus; |
| #ifdef CONFIG_PHYLIB |
| struct phy_device *phydev; |
| #endif |
| |
| #ifdef CONFIG_DM_ETH |
| #ifdef CONFIG_CLK |
| unsigned long pclk_rate; |
| #endif |
| phy_interface_t phy_interface; |
| #endif |
| }; |
| #ifndef CONFIG_DM_ETH |
| #define to_macb(_nd) container_of(_nd, struct macb_device, netdev) |
| #endif |
| |
| static int macb_is_gem(struct macb_device *macb) |
| { |
| return MACB_BFEXT(IDNUM, macb_readl(macb, MID)) == 0x2; |
| } |
| |
| #ifndef cpu_is_sama5d2 |
| #define cpu_is_sama5d2() 0 |
| #endif |
| |
| #ifndef cpu_is_sama5d4 |
| #define cpu_is_sama5d4() 0 |
| #endif |
| |
| static int gem_is_gigabit_capable(struct macb_device *macb) |
| { |
| /* |
| * The GEM controllers embedded in SAMA5D2 and SAMA5D4 are |
| * configured to support only 10/100. |
| */ |
| return macb_is_gem(macb) && !cpu_is_sama5d2() && !cpu_is_sama5d4(); |
| } |
| |
| static void macb_mdio_write(struct macb_device *macb, u8 reg, u16 value) |
| { |
| unsigned long netctl; |
| unsigned long netstat; |
| unsigned long frame; |
| |
| netctl = macb_readl(macb, NCR); |
| netctl |= MACB_BIT(MPE); |
| macb_writel(macb, NCR, netctl); |
| |
| frame = (MACB_BF(SOF, 1) |
| | MACB_BF(RW, 1) |
| | MACB_BF(PHYA, macb->phy_addr) |
| | MACB_BF(REGA, reg) |
| | MACB_BF(CODE, 2) |
| | MACB_BF(DATA, value)); |
| macb_writel(macb, MAN, frame); |
| |
| do { |
| netstat = macb_readl(macb, NSR); |
| } while (!(netstat & MACB_BIT(IDLE))); |
| |
| netctl = macb_readl(macb, NCR); |
| netctl &= ~MACB_BIT(MPE); |
| macb_writel(macb, NCR, netctl); |
| } |
| |
| static u16 macb_mdio_read(struct macb_device *macb, u8 reg) |
| { |
| unsigned long netctl; |
| unsigned long netstat; |
| unsigned long frame; |
| |
| netctl = macb_readl(macb, NCR); |
| netctl |= MACB_BIT(MPE); |
| macb_writel(macb, NCR, netctl); |
| |
| frame = (MACB_BF(SOF, 1) |
| | MACB_BF(RW, 2) |
| | MACB_BF(PHYA, macb->phy_addr) |
| | MACB_BF(REGA, reg) |
| | MACB_BF(CODE, 2)); |
| macb_writel(macb, MAN, frame); |
| |
| do { |
| netstat = macb_readl(macb, NSR); |
| } while (!(netstat & MACB_BIT(IDLE))); |
| |
| frame = macb_readl(macb, MAN); |
| |
| netctl = macb_readl(macb, NCR); |
| netctl &= ~MACB_BIT(MPE); |
| macb_writel(macb, NCR, netctl); |
| |
| return MACB_BFEXT(DATA, frame); |
| } |
| |
| void __weak arch_get_mdio_control(const char *name) |
| { |
| return; |
| } |
| |
| #if defined(CONFIG_CMD_MII) || defined(CONFIG_PHYLIB) |
| |
| int macb_miiphy_read(struct mii_dev *bus, int phy_adr, int devad, int reg) |
| { |
| u16 value = 0; |
| #ifdef CONFIG_DM_ETH |
| struct udevice *dev = eth_get_dev_by_name(bus->name); |
| struct macb_device *macb = dev_get_priv(dev); |
| #else |
| struct eth_device *dev = eth_get_dev_by_name(bus->name); |
| struct macb_device *macb = to_macb(dev); |
| #endif |
| |
| if (macb->phy_addr != phy_adr) |
| return -1; |
| |
| arch_get_mdio_control(bus->name); |
| value = macb_mdio_read(macb, reg); |
| |
| return value; |
| } |
| |
| int macb_miiphy_write(struct mii_dev *bus, int phy_adr, int devad, int reg, |
| u16 value) |
| { |
| #ifdef CONFIG_DM_ETH |
| struct udevice *dev = eth_get_dev_by_name(bus->name); |
| struct macb_device *macb = dev_get_priv(dev); |
| #else |
| struct eth_device *dev = eth_get_dev_by_name(bus->name); |
| struct macb_device *macb = to_macb(dev); |
| #endif |
| |
| if (macb->phy_addr != phy_adr) |
| return -1; |
| |
| arch_get_mdio_control(bus->name); |
| macb_mdio_write(macb, reg, value); |
| |
| return 0; |
| } |
| #endif |
| |
| #define RX 1 |
| #define TX 0 |
| static inline void macb_invalidate_ring_desc(struct macb_device *macb, bool rx) |
| { |
| if (rx) |
| invalidate_dcache_range(macb->rx_ring_dma, |
| ALIGN(macb->rx_ring_dma + MACB_RX_DMA_DESC_SIZE, |
| PKTALIGN)); |
| else |
| invalidate_dcache_range(macb->tx_ring_dma, |
| ALIGN(macb->tx_ring_dma + MACB_TX_DMA_DESC_SIZE, |
| PKTALIGN)); |
| } |
| |
| static inline void macb_flush_ring_desc(struct macb_device *macb, bool rx) |
| { |
| if (rx) |
| flush_dcache_range(macb->rx_ring_dma, macb->rx_ring_dma + |
| ALIGN(MACB_RX_DMA_DESC_SIZE, PKTALIGN)); |
| else |
| flush_dcache_range(macb->tx_ring_dma, macb->tx_ring_dma + |
| ALIGN(MACB_TX_DMA_DESC_SIZE, PKTALIGN)); |
| } |
| |
| static inline void macb_flush_rx_buffer(struct macb_device *macb) |
| { |
| flush_dcache_range(macb->rx_buffer_dma, macb->rx_buffer_dma + |
| ALIGN(MACB_RX_BUFFER_SIZE, PKTALIGN)); |
| } |
| |
| static inline void macb_invalidate_rx_buffer(struct macb_device *macb) |
| { |
| invalidate_dcache_range(macb->rx_buffer_dma, macb->rx_buffer_dma + |
| ALIGN(MACB_RX_BUFFER_SIZE, PKTALIGN)); |
| } |
| |
| #if defined(CONFIG_CMD_NET) |
| |
| static int _macb_send(struct macb_device *macb, const char *name, void *packet, |
| int length) |
| { |
| unsigned long paddr, ctrl; |
| unsigned int tx_head = macb->tx_head; |
| int i; |
| |
| paddr = dma_map_single(packet, length, DMA_TO_DEVICE); |
| |
| ctrl = length & TXBUF_FRMLEN_MASK; |
| ctrl |= TXBUF_FRAME_END; |
| if (tx_head == (MACB_TX_RING_SIZE - 1)) { |
| ctrl |= TXBUF_WRAP; |
| macb->tx_head = 0; |
| } else { |
| macb->tx_head++; |
| } |
| |
| macb->tx_ring[tx_head].ctrl = ctrl; |
| macb->tx_ring[tx_head].addr = paddr; |
| barrier(); |
| macb_flush_ring_desc(macb, TX); |
| /* Do we need check paddr and length is dcache line aligned? */ |
| flush_dcache_range(paddr, paddr + ALIGN(length, ARCH_DMA_MINALIGN)); |
| macb_writel(macb, NCR, MACB_BIT(TE) | MACB_BIT(RE) | MACB_BIT(TSTART)); |
| |
| /* |
| * I guess this is necessary because the networking core may |
| * re-use the transmit buffer as soon as we return... |
| */ |
| for (i = 0; i <= MACB_TX_TIMEOUT; i++) { |
| barrier(); |
| macb_invalidate_ring_desc(macb, TX); |
| ctrl = macb->tx_ring[tx_head].ctrl; |
| if (ctrl & TXBUF_USED) |
| break; |
| udelay(1); |
| } |
| |
| dma_unmap_single(packet, length, paddr); |
| |
| if (i <= MACB_TX_TIMEOUT) { |
| if (ctrl & TXBUF_UNDERRUN) |
| printf("%s: TX underrun\n", name); |
| if (ctrl & TXBUF_EXHAUSTED) |
| printf("%s: TX buffers exhausted in mid frame\n", name); |
| } else { |
| printf("%s: TX timeout\n", name); |
| } |
| |
| /* No one cares anyway */ |
| return 0; |
| } |
| |
| static void reclaim_rx_buffers(struct macb_device *macb, |
| unsigned int new_tail) |
| { |
| unsigned int i; |
| |
| i = macb->rx_tail; |
| |
| macb_invalidate_ring_desc(macb, RX); |
| while (i > new_tail) { |
| macb->rx_ring[i].addr &= ~RXADDR_USED; |
| i++; |
| if (i > MACB_RX_RING_SIZE) |
| i = 0; |
| } |
| |
| while (i < new_tail) { |
| macb->rx_ring[i].addr &= ~RXADDR_USED; |
| i++; |
| } |
| |
| barrier(); |
| macb_flush_ring_desc(macb, RX); |
| macb->rx_tail = new_tail; |
| } |
| |
| static int _macb_recv(struct macb_device *macb, uchar **packetp) |
| { |
| unsigned int next_rx_tail = macb->next_rx_tail; |
| void *buffer; |
| int length; |
| u32 status; |
| |
| macb->wrapped = false; |
| for (;;) { |
| macb_invalidate_ring_desc(macb, RX); |
| |
| if (!(macb->rx_ring[next_rx_tail].addr & RXADDR_USED)) |
| return -EAGAIN; |
| |
| status = macb->rx_ring[next_rx_tail].ctrl; |
| if (status & RXBUF_FRAME_START) { |
| if (next_rx_tail != macb->rx_tail) |
| reclaim_rx_buffers(macb, next_rx_tail); |
| macb->wrapped = false; |
| } |
| |
| if (status & RXBUF_FRAME_END) { |
| buffer = macb->rx_buffer + 128 * macb->rx_tail; |
| length = status & RXBUF_FRMLEN_MASK; |
| |
| macb_invalidate_rx_buffer(macb); |
| if (macb->wrapped) { |
| unsigned int headlen, taillen; |
| |
| headlen = 128 * (MACB_RX_RING_SIZE |
| - macb->rx_tail); |
| taillen = length - headlen; |
| memcpy((void *)net_rx_packets[0], |
| buffer, headlen); |
| memcpy((void *)net_rx_packets[0] + headlen, |
| macb->rx_buffer, taillen); |
| *packetp = (void *)net_rx_packets[0]; |
| } else { |
| *packetp = buffer; |
| } |
| |
| if (++next_rx_tail >= MACB_RX_RING_SIZE) |
| next_rx_tail = 0; |
| macb->next_rx_tail = next_rx_tail; |
| return length; |
| } else { |
| if (++next_rx_tail >= MACB_RX_RING_SIZE) { |
| macb->wrapped = true; |
| next_rx_tail = 0; |
| } |
| } |
| barrier(); |
| } |
| } |
| |
| static void macb_phy_reset(struct macb_device *macb, const char *name) |
| { |
| int i; |
| u16 status, adv; |
| |
| adv = ADVERTISE_CSMA | ADVERTISE_ALL; |
| macb_mdio_write(macb, MII_ADVERTISE, adv); |
| printf("%s: Starting autonegotiation...\n", name); |
| macb_mdio_write(macb, MII_BMCR, (BMCR_ANENABLE |
| | BMCR_ANRESTART)); |
| |
| for (i = 0; i < MACB_AUTONEG_TIMEOUT / 100; i++) { |
| status = macb_mdio_read(macb, MII_BMSR); |
| if (status & BMSR_ANEGCOMPLETE) |
| break; |
| udelay(100); |
| } |
| |
| if (status & BMSR_ANEGCOMPLETE) |
| printf("%s: Autonegotiation complete\n", name); |
| else |
| printf("%s: Autonegotiation timed out (status=0x%04x)\n", |
| name, status); |
| } |
| |
| static int macb_phy_find(struct macb_device *macb, const char *name) |
| { |
| int i; |
| u16 phy_id; |
| |
| /* Search for PHY... */ |
| for (i = 0; i < 32; i++) { |
| macb->phy_addr = i; |
| phy_id = macb_mdio_read(macb, MII_PHYSID1); |
| if (phy_id != 0xffff) { |
| printf("%s: PHY present at %d\n", name, i); |
| return 0; |
| } |
| } |
| |
| /* PHY isn't up to snuff */ |
| printf("%s: PHY not found\n", name); |
| |
| return -ENODEV; |
| } |
| |
| /** |
| * macb_linkspd_cb - Linkspeed change callback function |
| * @regs: Base Register of MACB devices |
| * @speed: Linkspeed |
| * Returns 0 when operation success and negative errno number |
| * when operation failed. |
| */ |
| int __weak macb_linkspd_cb(void *regs, unsigned int speed) |
| { |
| return 0; |
| } |
| |
| #ifdef CONFIG_DM_ETH |
| static int macb_phy_init(struct udevice *dev, const char *name) |
| #else |
| static int macb_phy_init(struct macb_device *macb, const char *name) |
| #endif |
| { |
| #ifdef CONFIG_DM_ETH |
| struct macb_device *macb = dev_get_priv(dev); |
| #endif |
| u32 ncfgr; |
| u16 phy_id, status, adv, lpa; |
| int media, speed, duplex; |
| int ret; |
| int i; |
| |
| arch_get_mdio_control(name); |
| /* Auto-detect phy_addr */ |
| ret = macb_phy_find(macb, name); |
| if (ret) |
| return ret; |
| |
| /* Check if the PHY is up to snuff... */ |
| phy_id = macb_mdio_read(macb, MII_PHYSID1); |
| if (phy_id == 0xffff) { |
| printf("%s: No PHY present\n", name); |
| return -ENODEV; |
| } |
| |
| #ifdef CONFIG_PHYLIB |
| #ifdef CONFIG_DM_ETH |
| macb->phydev = phy_connect(macb->bus, macb->phy_addr, dev, |
| macb->phy_interface); |
| #else |
| /* need to consider other phy interface mode */ |
| macb->phydev = phy_connect(macb->bus, macb->phy_addr, &macb->netdev, |
| PHY_INTERFACE_MODE_RGMII); |
| #endif |
| if (!macb->phydev) { |
| printf("phy_connect failed\n"); |
| return -ENODEV; |
| } |
| |
| phy_config(macb->phydev); |
| #endif |
| |
| status = macb_mdio_read(macb, MII_BMSR); |
| if (!(status & BMSR_LSTATUS)) { |
| /* Try to re-negotiate if we don't have link already. */ |
| macb_phy_reset(macb, name); |
| |
| for (i = 0; i < MACB_AUTONEG_TIMEOUT / 100; i++) { |
| status = macb_mdio_read(macb, MII_BMSR); |
| if (status & BMSR_LSTATUS) |
| break; |
| udelay(100); |
| } |
| } |
| |
| if (!(status & BMSR_LSTATUS)) { |
| printf("%s: link down (status: 0x%04x)\n", |
| name, status); |
| return -ENETDOWN; |
| } |
| |
| /* First check for GMAC and that it is GiB capable */ |
| if (gem_is_gigabit_capable(macb)) { |
| lpa = macb_mdio_read(macb, MII_STAT1000); |
| |
| if (lpa & (LPA_1000FULL | LPA_1000HALF)) { |
| duplex = ((lpa & LPA_1000FULL) ? 1 : 0); |
| |
| printf("%s: link up, 1000Mbps %s-duplex (lpa: 0x%04x)\n", |
| name, |
| duplex ? "full" : "half", |
| lpa); |
| |
| ncfgr = macb_readl(macb, NCFGR); |
| ncfgr &= ~(MACB_BIT(SPD) | MACB_BIT(FD)); |
| ncfgr |= GEM_BIT(GBE); |
| |
| if (duplex) |
| ncfgr |= MACB_BIT(FD); |
| |
| macb_writel(macb, NCFGR, ncfgr); |
| |
| ret = macb_linkspd_cb(macb->regs, _1000BASET); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| } |
| |
| /* fall back for EMAC checking */ |
| adv = macb_mdio_read(macb, MII_ADVERTISE); |
| lpa = macb_mdio_read(macb, MII_LPA); |
| media = mii_nway_result(lpa & adv); |
| speed = (media & (ADVERTISE_100FULL | ADVERTISE_100HALF) |
| ? 1 : 0); |
| duplex = (media & ADVERTISE_FULL) ? 1 : 0; |
| printf("%s: link up, %sMbps %s-duplex (lpa: 0x%04x)\n", |
| name, |
| speed ? "100" : "10", |
| duplex ? "full" : "half", |
| lpa); |
| |
| ncfgr = macb_readl(macb, NCFGR); |
| ncfgr &= ~(MACB_BIT(SPD) | MACB_BIT(FD) | GEM_BIT(GBE)); |
| if (speed) { |
| ncfgr |= MACB_BIT(SPD); |
| ret = macb_linkspd_cb(macb->regs, _100BASET); |
| } else { |
| ret = macb_linkspd_cb(macb->regs, _10BASET); |
| } |
| |
| if (ret) |
| return ret; |
| |
| if (duplex) |
| ncfgr |= MACB_BIT(FD); |
| macb_writel(macb, NCFGR, ncfgr); |
| |
| return 0; |
| } |
| |
| static int gmac_init_multi_queues(struct macb_device *macb) |
| { |
| int i, num_queues = 1; |
| u32 queue_mask; |
| |
| /* bit 0 is never set but queue 0 always exists */ |
| queue_mask = gem_readl(macb, DCFG6) & 0xff; |
| queue_mask |= 0x1; |
| |
| for (i = 1; i < MACB_MAX_QUEUES; i++) |
| if (queue_mask & (1 << i)) |
| num_queues++; |
| |
| macb->dummy_desc->ctrl = TXBUF_USED; |
| macb->dummy_desc->addr = 0; |
| flush_dcache_range(macb->dummy_desc_dma, macb->dummy_desc_dma + |
| ALIGN(MACB_TX_DUMMY_DMA_DESC_SIZE, PKTALIGN)); |
| |
| for (i = 1; i < num_queues; i++) |
| gem_writel_queue_TBQP(macb, macb->dummy_desc_dma, i - 1); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_DM_ETH |
| static int _macb_init(struct udevice *dev, const char *name) |
| #else |
| static int _macb_init(struct macb_device *macb, const char *name) |
| #endif |
| { |
| #ifdef CONFIG_DM_ETH |
| struct macb_device *macb = dev_get_priv(dev); |
| #endif |
| unsigned long paddr; |
| int ret; |
| int i; |
| |
| /* |
| * macb_halt should have been called at some point before now, |
| * so we'll assume the controller is idle. |
| */ |
| |
| /* initialize DMA descriptors */ |
| paddr = macb->rx_buffer_dma; |
| for (i = 0; i < MACB_RX_RING_SIZE; i++) { |
| if (i == (MACB_RX_RING_SIZE - 1)) |
| paddr |= RXADDR_WRAP; |
| macb->rx_ring[i].addr = paddr; |
| macb->rx_ring[i].ctrl = 0; |
| paddr += 128; |
| } |
| macb_flush_ring_desc(macb, RX); |
| macb_flush_rx_buffer(macb); |
| |
| for (i = 0; i < MACB_TX_RING_SIZE; i++) { |
| macb->tx_ring[i].addr = 0; |
| if (i == (MACB_TX_RING_SIZE - 1)) |
| macb->tx_ring[i].ctrl = TXBUF_USED | TXBUF_WRAP; |
| else |
| macb->tx_ring[i].ctrl = TXBUF_USED; |
| } |
| macb_flush_ring_desc(macb, TX); |
| |
| macb->rx_tail = 0; |
| macb->tx_head = 0; |
| macb->tx_tail = 0; |
| macb->next_rx_tail = 0; |
| |
| #ifdef CONFIG_MACB_ZYNQ |
| macb_writel(macb, DMACFG, MACB_ZYNQ_GEM_DMACR_INIT); |
| #endif |
| |
| macb_writel(macb, RBQP, macb->rx_ring_dma); |
| macb_writel(macb, TBQP, macb->tx_ring_dma); |
| |
| if (macb_is_gem(macb)) { |
| /* Check the multi queue and initialize the queue for tx */ |
| gmac_init_multi_queues(macb); |
| |
| /* |
| * When the GMAC IP with GE feature, this bit is used to |
| * select interface between RGMII and GMII. |
| * When the GMAC IP without GE feature, this bit is used |
| * to select interface between RMII and MII. |
| */ |
| #ifdef CONFIG_DM_ETH |
| if ((macb->phy_interface == PHY_INTERFACE_MODE_RMII) || |
| (macb->phy_interface == PHY_INTERFACE_MODE_RGMII)) |
| gem_writel(macb, UR, GEM_BIT(RGMII)); |
| else |
| gem_writel(macb, UR, 0); |
| #else |
| #if defined(CONFIG_RGMII) || defined(CONFIG_RMII) |
| gem_writel(macb, UR, GEM_BIT(RGMII)); |
| #else |
| gem_writel(macb, UR, 0); |
| #endif |
| #endif |
| } else { |
| /* choose RMII or MII mode. This depends on the board */ |
| #ifdef CONFIG_DM_ETH |
| #ifdef CONFIG_AT91FAMILY |
| if (macb->phy_interface == PHY_INTERFACE_MODE_RMII) { |
| macb_writel(macb, USRIO, |
| MACB_BIT(RMII) | MACB_BIT(CLKEN)); |
| } else { |
| macb_writel(macb, USRIO, MACB_BIT(CLKEN)); |
| } |
| #else |
| if (macb->phy_interface == PHY_INTERFACE_MODE_RMII) |
| macb_writel(macb, USRIO, 0); |
| else |
| macb_writel(macb, USRIO, MACB_BIT(MII)); |
| #endif |
| #else |
| #ifdef CONFIG_RMII |
| #ifdef CONFIG_AT91FAMILY |
| macb_writel(macb, USRIO, MACB_BIT(RMII) | MACB_BIT(CLKEN)); |
| #else |
| macb_writel(macb, USRIO, 0); |
| #endif |
| #else |
| #ifdef CONFIG_AT91FAMILY |
| macb_writel(macb, USRIO, MACB_BIT(CLKEN)); |
| #else |
| macb_writel(macb, USRIO, MACB_BIT(MII)); |
| #endif |
| #endif /* CONFIG_RMII */ |
| #endif |
| } |
| |
| #ifdef CONFIG_DM_ETH |
| ret = macb_phy_init(dev, name); |
| #else |
| ret = macb_phy_init(macb, name); |
| #endif |
| if (ret) |
| return ret; |
| |
| /* Enable TX and RX */ |
| macb_writel(macb, NCR, MACB_BIT(TE) | MACB_BIT(RE)); |
| |
| return 0; |
| } |
| |
| static void _macb_halt(struct macb_device *macb) |
| { |
| u32 ncr, tsr; |
| |
| /* Halt the controller and wait for any ongoing transmission to end. */ |
| ncr = macb_readl(macb, NCR); |
| ncr |= MACB_BIT(THALT); |
| macb_writel(macb, NCR, ncr); |
| |
| do { |
| tsr = macb_readl(macb, TSR); |
| } while (tsr & MACB_BIT(TGO)); |
| |
| /* Disable TX and RX, and clear statistics */ |
| macb_writel(macb, NCR, MACB_BIT(CLRSTAT)); |
| } |
| |
| static int _macb_write_hwaddr(struct macb_device *macb, unsigned char *enetaddr) |
| { |
| u32 hwaddr_bottom; |
| u16 hwaddr_top; |
| |
| /* set hardware address */ |
| hwaddr_bottom = enetaddr[0] | enetaddr[1] << 8 | |
| enetaddr[2] << 16 | enetaddr[3] << 24; |
| macb_writel(macb, SA1B, hwaddr_bottom); |
| hwaddr_top = enetaddr[4] | enetaddr[5] << 8; |
| macb_writel(macb, SA1T, hwaddr_top); |
| return 0; |
| } |
| |
| static u32 macb_mdc_clk_div(int id, struct macb_device *macb) |
| { |
| u32 config; |
| #if defined(CONFIG_DM_ETH) && defined(CONFIG_CLK) |
| unsigned long macb_hz = macb->pclk_rate; |
| #else |
| unsigned long macb_hz = get_macb_pclk_rate(id); |
| #endif |
| |
| if (macb_hz < 20000000) |
| config = MACB_BF(CLK, MACB_CLK_DIV8); |
| else if (macb_hz < 40000000) |
| config = MACB_BF(CLK, MACB_CLK_DIV16); |
| else if (macb_hz < 80000000) |
| config = MACB_BF(CLK, MACB_CLK_DIV32); |
| else |
| config = MACB_BF(CLK, MACB_CLK_DIV64); |
| |
| return config; |
| } |
| |
| static u32 gem_mdc_clk_div(int id, struct macb_device *macb) |
| { |
| u32 config; |
| |
| #if defined(CONFIG_DM_ETH) && defined(CONFIG_CLK) |
| unsigned long macb_hz = macb->pclk_rate; |
| #else |
| unsigned long macb_hz = get_macb_pclk_rate(id); |
| #endif |
| |
| if (macb_hz < 20000000) |
| config = GEM_BF(CLK, GEM_CLK_DIV8); |
| else if (macb_hz < 40000000) |
| config = GEM_BF(CLK, GEM_CLK_DIV16); |
| else if (macb_hz < 80000000) |
| config = GEM_BF(CLK, GEM_CLK_DIV32); |
| else if (macb_hz < 120000000) |
| config = GEM_BF(CLK, GEM_CLK_DIV48); |
| else if (macb_hz < 160000000) |
| config = GEM_BF(CLK, GEM_CLK_DIV64); |
| else |
| config = GEM_BF(CLK, GEM_CLK_DIV96); |
| |
| return config; |
| } |
| |
| /* |
| * Get the DMA bus width field of the network configuration register that we |
| * should program. We find the width from decoding the design configuration |
| * register to find the maximum supported data bus width. |
| */ |
| static u32 macb_dbw(struct macb_device *macb) |
| { |
| switch (GEM_BFEXT(DBWDEF, gem_readl(macb, DCFG1))) { |
| case 4: |
| return GEM_BF(DBW, GEM_DBW128); |
| case 2: |
| return GEM_BF(DBW, GEM_DBW64); |
| case 1: |
| default: |
| return GEM_BF(DBW, GEM_DBW32); |
| } |
| } |
| |
| static void _macb_eth_initialize(struct macb_device *macb) |
| { |
| int id = 0; /* This is not used by functions we call */ |
| u32 ncfgr; |
| |
| /* TODO: we need check the rx/tx_ring_dma is dcache line aligned */ |
| macb->rx_buffer = dma_alloc_coherent(MACB_RX_BUFFER_SIZE, |
| &macb->rx_buffer_dma); |
| macb->rx_ring = dma_alloc_coherent(MACB_RX_DMA_DESC_SIZE, |
| &macb->rx_ring_dma); |
| macb->tx_ring = dma_alloc_coherent(MACB_TX_DMA_DESC_SIZE, |
| &macb->tx_ring_dma); |
| macb->dummy_desc = dma_alloc_coherent(MACB_TX_DUMMY_DMA_DESC_SIZE, |
| &macb->dummy_desc_dma); |
| |
| /* |
| * Do some basic initialization so that we at least can talk |
| * to the PHY |
| */ |
| if (macb_is_gem(macb)) { |
| ncfgr = gem_mdc_clk_div(id, macb); |
| ncfgr |= macb_dbw(macb); |
| } else { |
| ncfgr = macb_mdc_clk_div(id, macb); |
| } |
| |
| macb_writel(macb, NCFGR, ncfgr); |
| } |
| |
| #ifndef CONFIG_DM_ETH |
| static int macb_send(struct eth_device *netdev, void *packet, int length) |
| { |
| struct macb_device *macb = to_macb(netdev); |
| |
| return _macb_send(macb, netdev->name, packet, length); |
| } |
| |
| static int macb_recv(struct eth_device *netdev) |
| { |
| struct macb_device *macb = to_macb(netdev); |
| uchar *packet; |
| int length; |
| |
| macb->wrapped = false; |
| for (;;) { |
| macb->next_rx_tail = macb->rx_tail; |
| length = _macb_recv(macb, &packet); |
| if (length >= 0) { |
| net_process_received_packet(packet, length); |
| reclaim_rx_buffers(macb, macb->next_rx_tail); |
| } else if (length < 0) { |
| return length; |
| } |
| } |
| } |
| |
| static int macb_init(struct eth_device *netdev, bd_t *bd) |
| { |
| struct macb_device *macb = to_macb(netdev); |
| |
| return _macb_init(macb, netdev->name); |
| } |
| |
| static void macb_halt(struct eth_device *netdev) |
| { |
| struct macb_device *macb = to_macb(netdev); |
| |
| return _macb_halt(macb); |
| } |
| |
| static int macb_write_hwaddr(struct eth_device *netdev) |
| { |
| struct macb_device *macb = to_macb(netdev); |
| |
| return _macb_write_hwaddr(macb, netdev->enetaddr); |
| } |
| |
| int macb_eth_initialize(int id, void *regs, unsigned int phy_addr) |
| { |
| struct macb_device *macb; |
| struct eth_device *netdev; |
| |
| macb = malloc(sizeof(struct macb_device)); |
| if (!macb) { |
| printf("Error: Failed to allocate memory for MACB%d\n", id); |
| return -1; |
| } |
| memset(macb, 0, sizeof(struct macb_device)); |
| |
| netdev = &macb->netdev; |
| |
| macb->regs = regs; |
| macb->phy_addr = phy_addr; |
| |
| if (macb_is_gem(macb)) |
| sprintf(netdev->name, "gmac%d", id); |
| else |
| sprintf(netdev->name, "macb%d", id); |
| |
| netdev->init = macb_init; |
| netdev->halt = macb_halt; |
| netdev->send = macb_send; |
| netdev->recv = macb_recv; |
| netdev->write_hwaddr = macb_write_hwaddr; |
| |
| _macb_eth_initialize(macb); |
| |
| eth_register(netdev); |
| |
| #if defined(CONFIG_CMD_MII) || defined(CONFIG_PHYLIB) |
| int retval; |
| struct mii_dev *mdiodev = mdio_alloc(); |
| if (!mdiodev) |
| return -ENOMEM; |
| strncpy(mdiodev->name, netdev->name, MDIO_NAME_LEN); |
| mdiodev->read = macb_miiphy_read; |
| mdiodev->write = macb_miiphy_write; |
| |
| retval = mdio_register(mdiodev); |
| if (retval < 0) |
| return retval; |
| macb->bus = miiphy_get_dev_by_name(netdev->name); |
| #endif |
| return 0; |
| } |
| #endif /* !CONFIG_DM_ETH */ |
| |
| #ifdef CONFIG_DM_ETH |
| |
| static int macb_start(struct udevice *dev) |
| { |
| return _macb_init(dev, dev->name); |
| } |
| |
| static int macb_send(struct udevice *dev, void *packet, int length) |
| { |
| struct macb_device *macb = dev_get_priv(dev); |
| |
| return _macb_send(macb, dev->name, packet, length); |
| } |
| |
| static int macb_recv(struct udevice *dev, int flags, uchar **packetp) |
| { |
| struct macb_device *macb = dev_get_priv(dev); |
| |
| macb->next_rx_tail = macb->rx_tail; |
| macb->wrapped = false; |
| |
| return _macb_recv(macb, packetp); |
| } |
| |
| static int macb_free_pkt(struct udevice *dev, uchar *packet, int length) |
| { |
| struct macb_device *macb = dev_get_priv(dev); |
| |
| reclaim_rx_buffers(macb, macb->next_rx_tail); |
| |
| return 0; |
| } |
| |
| static void macb_stop(struct udevice *dev) |
| { |
| struct macb_device *macb = dev_get_priv(dev); |
| |
| _macb_halt(macb); |
| } |
| |
| static int macb_write_hwaddr(struct udevice *dev) |
| { |
| struct eth_pdata *plat = dev_get_platdata(dev); |
| struct macb_device *macb = dev_get_priv(dev); |
| |
| return _macb_write_hwaddr(macb, plat->enetaddr); |
| } |
| |
| static const struct eth_ops macb_eth_ops = { |
| .start = macb_start, |
| .send = macb_send, |
| .recv = macb_recv, |
| .stop = macb_stop, |
| .free_pkt = macb_free_pkt, |
| .write_hwaddr = macb_write_hwaddr, |
| }; |
| |
| #ifdef CONFIG_CLK |
| static int macb_enable_clk(struct udevice *dev) |
| { |
| struct macb_device *macb = dev_get_priv(dev); |
| struct clk clk; |
| ulong clk_rate; |
| int ret; |
| |
| ret = clk_get_by_index(dev, 0, &clk); |
| if (ret) |
| return -EINVAL; |
| |
| /* |
| * Zynq clock driver didn't support for enable or disable |
| * clock. Hence, clk_enable() didn't apply for Zynq |
| */ |
| #ifndef CONFIG_MACB_ZYNQ |
| ret = clk_enable(&clk); |
| if (ret) |
| return ret; |
| #endif |
| |
| clk_rate = clk_get_rate(&clk); |
| if (!clk_rate) |
| return -EINVAL; |
| |
| macb->pclk_rate = clk_rate; |
| |
| return 0; |
| } |
| #endif |
| |
| static int macb_eth_probe(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_platdata(dev); |
| struct macb_device *macb = dev_get_priv(dev); |
| const char *phy_mode; |
| __maybe_unused int ret; |
| |
| phy_mode = fdt_getprop(gd->fdt_blob, dev_of_offset(dev), "phy-mode", |
| NULL); |
| if (phy_mode) |
| macb->phy_interface = phy_get_interface_by_name(phy_mode); |
| if (macb->phy_interface == -1) { |
| debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode); |
| return -EINVAL; |
| } |
| |
| macb->regs = (void *)pdata->iobase; |
| |
| #ifdef CONFIG_CLK |
| ret = macb_enable_clk(dev); |
| if (ret) |
| return ret; |
| #endif |
| |
| _macb_eth_initialize(macb); |
| |
| #if defined(CONFIG_CMD_MII) || defined(CONFIG_PHYLIB) |
| macb->bus = mdio_alloc(); |
| if (!macb->bus) |
| return -ENOMEM; |
| strncpy(macb->bus->name, dev->name, MDIO_NAME_LEN); |
| macb->bus->read = macb_miiphy_read; |
| macb->bus->write = macb_miiphy_write; |
| |
| ret = mdio_register(macb->bus); |
| if (ret < 0) |
| return ret; |
| macb->bus = miiphy_get_dev_by_name(dev->name); |
| #endif |
| |
| return 0; |
| } |
| |
| static int macb_eth_remove(struct udevice *dev) |
| { |
| struct macb_device *macb = dev_get_priv(dev); |
| |
| #ifdef CONFIG_PHYLIB |
| free(macb->phydev); |
| #endif |
| mdio_unregister(macb->bus); |
| mdio_free(macb->bus); |
| |
| return 0; |
| } |
| |
| /** |
| * macb_late_eth_ofdata_to_platdata |
| * @dev: udevice struct |
| * Returns 0 when operation success and negative errno number |
| * when operation failed. |
| */ |
| int __weak macb_late_eth_ofdata_to_platdata(struct udevice *dev) |
| { |
| return 0; |
| } |
| |
| static int macb_eth_ofdata_to_platdata(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_platdata(dev); |
| |
| pdata->iobase = devfdt_get_addr(dev); |
| |
| return macb_late_eth_ofdata_to_platdata(dev); |
| } |
| |
| static const struct udevice_id macb_eth_ids[] = { |
| { .compatible = "cdns,macb" }, |
| { .compatible = "cdns,at91sam9260-macb" }, |
| { .compatible = "atmel,sama5d2-gem" }, |
| { .compatible = "atmel,sama5d3-gem" }, |
| { .compatible = "atmel,sama5d4-gem" }, |
| { .compatible = "cdns,zynq-gem" }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(eth_macb) = { |
| .name = "eth_macb", |
| .id = UCLASS_ETH, |
| .of_match = macb_eth_ids, |
| .ofdata_to_platdata = macb_eth_ofdata_to_platdata, |
| .probe = macb_eth_probe, |
| .remove = macb_eth_remove, |
| .ops = &macb_eth_ops, |
| .priv_auto_alloc_size = sizeof(struct macb_device), |
| .platdata_auto_alloc_size = sizeof(struct eth_pdata), |
| }; |
| #endif |
| |
| #endif |