| Freescale MPC8641HPCN board |
| =========================== |
| |
| Created 05/24/2006 Haiying Wang |
| ------------------------------- |
| |
| 1. Building U-Boot |
| ------------------ |
| The 86xx HPCN code base is known to compile using: |
| Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3 |
| |
| $ make MPC8641HPCN_config |
| Configuring for MPC8641HPCN board... |
| |
| $ make |
| |
| |
| 2. Switch and Jumper Setting |
| ---------------------------- |
| Jumpers: |
| J14 Pins 1-2 (near plcc32 socket) |
| |
| Switches: |
| SW1(1-5) = 01100 CFG_COREPLL = 01000 :: CORE = 2:1 |
| 01100 :: CORE = 2.5:1 |
| 10000 :: CORE = 3:1 |
| 11100 :: CORE = 3.5:1 |
| 10100 :: CORE = 4:1 |
| 01110 :: CORE = 4.5:1 |
| SW1(6-8) = 001 CFG_SYSCLK = 000 :: SYSCLK = 33MHz |
| 001 :: SYSCLK = 40MHz |
| |
| SW2(1-4) = 1100 CFG_CCBPLL = 0010 :: 2X |
| 0100 :: 4X |
| 0110 :: 6X |
| 1000 :: 8X |
| 1010 :: 10X |
| 1100 :: 12X |
| 1110 :: 14X |
| 0000 :: 16X |
| SW2(5-8) = 1110 CFG_BOOTLOC = 1110 :: boot 16-bit localbus |
| |
| SW3(1-7) = 0011000 CFG_VID = 0011000 :: VCORE = 1.2V |
| 0100000 :: VCORE = 1.11V |
| SW3(8) = 0 VCC_PLAT = 0 :: VCC_PLAT = 1.2V |
| 1 :: VCC_PLAT = 1.0V |
| |
| SW4(1-2) = 11 CFG_HOSTMODE = 11 :: both prots host/root |
| SW4(3-4) = 11 CFG_BOOTSEQ = 11 :: no boot seq |
| SW4(5-8) = 0011 CFG_IOPORT = 0011 :: both PEX |
| |
| SW5(1) = 1 CFG_FLASHMAP = 1 :: boot from flash |
| 0 :: boot from PromJet |
| SW5(2) = 1 CFG_FLASHBANK = 1 :: swap upper/lower |
| halves (virtual banks) |
| 0 :: normal |
| SW5(3) = 0 CFG_FLASHWP = 0 :: not protected |
| SW5(4) = 0 CFG_PORTDIV = 1 :: 2:1 for PD4 |
| 1:1 for PD6 |
| SW5(5-6) = 11 CFG_PIXISOPT = 11 :: s/w determined |
| SW5(7-8) = 11 CFG_LADOPT = 11 :: s/w determined |
| |
| SW6(1) = 1 CFG_CPUBOOT = 1 :: no boot holdoff |
| SW6(2) = 1 CFG_BOOTADDR = 1 :: no traslation |
| SW6(3-5) = 000 CFG_REFCLKSEL = 000 :: 100MHZ |
| SW6(6) = 1 CFG_SERROM_ADDR= 1 :: |
| SW6(7) = 1 CFG_MEMDEBUG = 1 :: |
| SW6(8) = 1 CFG_DDRDEBUG = 1 :: |
| |
| SW8(1) = 1 ACZ_SYNC = 1 :: 48MHz on TP49 |
| SW8(2) = 1 ACB_SYNC = 1 :: THRMTRIP disabled |
| SW8(3) = 1 ACZ_SDOUT = 1 :: p4 mode |
| SW8(4) = 1 ACB_SDOUT = 1 :: PATA freq. = 133MHz |
| SW8(5) = 0 SUSLED = 0 :: SouthBridge Mode |
| SW8(6) = 0 SPREAD = 0 :: REFCLK SSCG Disabled |
| SW8(7) = 1 ACPWR = 1 :: non-battery |
| SW8(8) = 0 CFG_IDWP = 0 :: write enable |
| |
| |
| 3. Flash U-Boot |
| --------------- |
| The flash range 0xFF800000 to 0xFFFFFFFF can be divided into 2 halves. |
| It is possible to use either half to boot using u-boot. Switch 5 bit 2 |
| is used for this purpose. |
| |
| 0xFF800000 to 0xFFBFFFFF - 4MB |
| 0xFFC00000 to 0xFFFFFFFF - 4MB |
| When this bit is 0, U-Boot is at 0xFFF00000. |
| When this bit is 1, U-Boot is at 0xFFB00000. |
| |
| Use the above mentioned flash commands to program the other half, and |
| use switch 5, bit 2 to alternate between the halves. Note: The booting |
| version of U-Boot will always be at 0xFFF00000. |
| |
| To Flash U-Boot into the booting bank (0xFFC00000 - 0xFFFFFFFF): |
| |
| tftp 1000000 u-boot.bin |
| protect off all |
| erase fff00000 ffffffff |
| cp.b 1000000 fff00100 80000 |
| |
| To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF): |
| |
| tftp 1000000 u-boot.bin |
| erase ffb00000 ffbfffff |
| cp.b 1000000 ffb00100 80000 |
| |
| |
| 4. Memory Map |
| ------------- |
| |
| Memory Range Device Size |
| ------------ ------ ---- |
| 0x0000_0000 0x7fff_ffff DDR 2G |
| 0x8000_0000 0x9fff_ffff PCI1/PEX1 MEM 512M |
| 0xa000_0000 0xafff_ffff PCI2/PEX2 MEM 512M |
| 0xf800_0000 0xf80f_ffff CCSR 1M |
| 0xf810_0000 0xf81f_ffff PIXIS 1M |
| 0xf840_0000 0xf840_3fff Stack space 32K |
| 0xe200_0000 0xe2ff_ffff PCI1/PEX1 IO 16M |
| 0xe300_0000 0xe3ff_ffff PCI2/PEX2 IO 16M |
| 0xfe00_0000 0xfeff_ffff Flash(alternate)16M |
| 0xff00_0000 0xffff_ffff Flash(boot bank)16M |
| |
| 5. pixis_reset command |
| -------------------- |
| A new command, "pixis_reset", is introduced to reset mpc8641hpcn board |
| using the FPGA sequencer. When the board restarts, it has the option |
| of using either the current or alternate flash bank as the boot |
| image, with or without the watchdog timer enabled, and finally with |
| or without frequency changes. |
| |
| Usage is; |
| |
| pixis_reset |
| pixis_reset altbank |
| pixis_reset altbank wd |
| pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio> |
| pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio> |
| |
| Examples; |
| |
| /* reset to current bank, like "reset" command */ |
| pixis_reset |
| |
| /* reset board but use the to alternate flash bank */ |
| pixis_reset altbank |
| |
| /* reset board, use alternate flash bank with watchdog timer enabled*/ |
| pixis_reset altbank wd |
| |
| /* reset board to alternate bank with frequency changed. |
| * 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio |
| */ |
| pixis-reset altbank cf 40 2.5 10 |
| |
| Valid clock choices are in the 8641 Reference Manuals. |