blob: f0440cda1a71ecc5c45e3ac11ff78e5feebb68f3 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/
*/
/dts-v1/;
#include "k3-j7200-som-p0.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/net/ti-dp83867.h>
#include <dt-bindings/mux/ti-serdes.h>
#include <dt-bindings/phy/phy.h>
/ {
chosen {
stdout-path = "serial2:115200n8";
bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
};
aliases {
remoteproc0 = &mcu_r5fss0_core0;
remoteproc1 = &mcu_r5fss0_core1;
remoteproc2 = &main_r5fss0_core0;
remoteproc3 = &main_r5fss0_core1;
};
vdd_mmc1: fixedregulator-sd {
compatible = "regulator-fixed";
regulator-name = "vdd_mmc1";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
enable-active-high;
gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
};
vdd_sd_dv: gpio-regulator-vdd-sd-dv {
compatible = "regulator-gpio";
regulator-name = "vdd_sd_dv";
pinctrl-names = "default";
pinctrl-0 = <&vdd_sd_dv_pins_default>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
states = <1800000 0x0
3300000 0x1>;
};
};
&wkup_pmx0 {
wkup_i2c0_pins_default: wkup-i2c0-pins-default {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x100, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */
J721E_WKUP_IOPAD(0x104, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
>;
};
wkup_gpio_pins_default: wkup-gpio-pins-default {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0xd8, PIN_INPUT, 7) /* (C14) WKUP_GPIO0_6 */
>;
};
mcu_cpsw_pins_default: mcu-cpsw-pins-default {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_TXC */
J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
>;
};
mcu_mdio_pins_default: mcu-mdio1-pins-default {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>;
};
};
&main_pmx0 {
main_i2c0_pins_default: main-i2c0-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
>;
};
main_i2c1_pins_default: main-i2c1-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
J721E_IOPAD(0xe0, PIN_INPUT_PULLUP, 3) /* (T3) EXT_REFCLK1.I2C1_SDA */
>;
};
main_mmc1_pins_default: main-mmc1-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0x104, PIN_INPUT, 0) /* (M20) MMC1_CMD */
J721E_IOPAD(0x100, PIN_INPUT, 0) /* (P21) MMC1_CLK */
J721E_IOPAD(0xfc, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
J721E_IOPAD(0xf8, PIN_INPUT, 0) /* (M19) MMC1_DAT0 */
J721E_IOPAD(0xf4, PIN_INPUT, 0) /* (N21) MMC1_DAT1 */
J721E_IOPAD(0xf0, PIN_INPUT, 0) /* (N20) MMC1_DAT2 */
J721E_IOPAD(0xec, PIN_INPUT, 0) /* (N19) MMC1_DAT3 */
J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
>;
};
vdd_sd_dv_pins_default: vdd_sd_dv_pins_default {
pinctrl-single,pins = <
J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
>;
};
main_usbss0_pins_default: main-usbss0-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>;
};
};
&wkup_uart0 {
/* Wakeup UART is used by System firmware */
status = "reserved";
};
&main_uart0 {
/* Shared with ATF on this platform */
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
};
&main_uart2 {
/* MAIN UART 2 is used by R5F firmware */
status = "reserved";
};
&main_uart3 {
/* UART not brought out */
status = "disabled";
};
&main_uart4 {
/* UART not brought out */
status = "disabled";
};
&main_uart5 {
/* UART not brought out */
status = "disabled";
};
&main_uart6 {
/* UART not brought out */
status = "disabled";
};
&main_uart7 {
/* UART not brought out */
status = "disabled";
};
&main_uart8 {
/* UART not brought out */
status = "disabled";
};
&main_uart9 {
/* UART not brought out */
status = "disabled";
};
&mcu_cpsw {
pinctrl-names = "default";
pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
};
&davinci_mdio {
phy0: ethernet-phy@0 {
reg = <0>;
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
};
};
&cpsw_port1 {
phy-mode = "rgmii-rxid";
phy-handle = <&phy0>;
};
&main_i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&main_i2c0_pins_default>;
clock-frequency = <400000>;
exp1: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
};
exp2: gpio@22 {
compatible = "ti,tca6424";
reg = <0x22>;
gpio-controller;
#gpio-cells = <2>;
};
};
/*
* The j7200 CPB board is identical to the CPB used for J721E, the SOMs can be
* swapped on the CPB.
*
* main_i2c1 of J7200 is connected to the CPB i2c bus labeled as i2c3.
* The i2c1 of the CPB (as it is labeled) is not connected to j7200.
*/
&main_i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&main_i2c1_pins_default>;
clock-frequency = <400000>;
exp3: gpio@20 {
compatible = "ti,tca6408";
reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names = "CODEC_RSTz", "CODEC_SPARE1", "UB926_RESETn",
"UB926_LOCK", "UB926_PWR_SW_CNTRL",
"UB926_TUNER_RESET", "UB926_GPIO_SPARE", "";
};
};
&main_sdhci0 {
/* eMMC */
non-removable;
ti,driver-strength-ohm = <50>;
disable-wp;
};
&main_sdhci1 {
/* SD card */
pinctrl-0 = <&main_mmc1_pins_default>;
pinctrl-names = "default";
vmmc-supply = <&vdd_mmc1>;
vqmmc-supply = <&vdd_sd_dv>;
ti,driver-strength-ohm = <50>;
disable-wp;
};
&serdes_ln_ctrl {
idle-states = <J7200_SERDES0_LANE0_PCIE1_LANE0>, <J7200_SERDES0_LANE1_PCIE1_LANE1>,
<J7200_SERDES0_LANE2_QSGMII_LANE1>, <J7200_SERDES0_LANE3_IP4_UNUSED>;
};
&usb_serdes_mux {
idle-states = <1>; /* USB0 to SERDES lane 3 */
};
&usbss0 {
pinctrl-names = "default";
pinctrl-0 = <&main_usbss0_pins_default>;
ti,vbus-divider;
ti,usb2-only;
};
&usb0 {
dr_mode = "otg";
maximum-speed = "high-speed";
};
&tscadc0 {
adc {
ti,adc-channels = <0 1 2 3 4 5 6 7>;
};
};
&serdes_refclk {
clock-frequency = <100000000>;
};
&serdes0 {
serdes0_pcie_link: link@0 {
reg = <0>;
cdns,num-lanes = <2>;
#phy-cells = <0>;
cdns,phy-type = <PHY_TYPE_PCIE>;
resets = <&serdes_wiz0 1>, <&serdes_wiz0 2>;
};
serdes0_qsgmii_link: link@1 {
reg = <2>;
cdns,num-lanes = <1>;
#phy-cells = <0>;
cdns,phy-type = <PHY_TYPE_QSGMII>;
resets = <&serdes_wiz0 3>;
};
};