| .. SPDX-License-Identifier: GPL-2.0+: |
| |
| saves command |
| ============= |
| |
| Synopsis |
| -------- |
| |
| :: |
| |
| saves [offset [size [baud]]] |
| |
| Description |
| ----------- |
| |
| The *saves* command is used to transfer a file from the device via the serial |
| line using the Motorola S-record file format. |
| |
| offset |
| start address of memory area to save, defaults to 0x0 |
| |
| size |
| size of memory area to save, defaults to 0x0 |
| |
| baud |
| baud rate to use for upload. This parameter is only available if |
| CONFIG_SYS_LOADS_BAUD_CHANGE=y |
| |
| Example |
| ------- |
| |
| In the example the *screen* command is used to connect to the U-Boot serial |
| console. |
| |
| In a first screen session a file is loaded from the SD-card and the *saves* |
| command is invoked. <CTRL+A><k> is used to kill the screen session. |
| |
| A new screen session is started which logs the output to a file and the |
| <ENTER> key is hit to start the file output. <CTRL+A><k> is issued to kill the |
| screen session. |
| |
| The log file is converted to a binary file using the *srec_cat* command. |
| A negative offset of -1337982976 (= -0x4c000000) is applied to compensate for |
| the offset used in the *saves* command. |
| |
| .. code-block:: |
| |
| $ screen /dev/ttyUSB0 115200 |
| => echo $scriptaddr |
| 0x4FC00000 |
| => load mmc 0:1 $scriptaddr boot.txt |
| 124 bytes read in 1 ms (121.1 KiB/s) |
| => saves $scriptaddr $filesize |
| ## Ready for S-Record upload, press ENTER to proceed ... |
| Really kill this window [y/n] |
| $ screen -Logfile out.srec -L /dev/ttyUSB0 115200 |
| S0030000FC |
| S3154FC00000736574656E76206175746F6C6F616420AD |
| S3154FC000106E6F0A646863700A6C6F6164206D6D633E |
| S3154FC0002020303A3120246664745F616464725F72B3 |
| S3154FC00030206474620A6C6F6164206D6D6320303AC0 |
| S3154FC000403120246B65726E656C5F616464725F72DA |
| S3154FC0005020736E702E6566690A626F6F74656669C6 |
| S3154FC0006020246B65726E656C5F616464725F7220CB |
| S3114FC00070246664745F616464725F720A38 |
| S70500000000FA |
| ## S-Record upload complete |
| => |
| Really kill this window [y/n] |
| $ srec_cat out.srec -offset -1337982976 -Output out.txt -binary 2>/dev/null |
| $ cat out.txt |
| setenv autoload no |
| dhcp |
| load mmc 0:1 $fdt_addr_r dtb |
| load mmc 0:1 $kernel_addr_r snp.efi |
| bootefi $kernel_addr_r $fdt_addr_r |
| $ |
| |
| Configuration |
| ------------- |
| |
| The command is only available if CONFIG_CMD_SAVES=y. The parameter to set the |
| baud rate is only available if CONFIG_SYS_LOADS_BAUD_CHANGE=y |
| |
| Return value |
| ------------ |
| |
| The return value $? is 0 (true) on success, 1 (false) otherwise. |