blob: bb3fbc71ef65196b790fe85107515203ebda7e78 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2015-2016 Freescale Semiconductor, Inc.
* Copyright 2017 NXP
*/
#include <common.h>
#include <dm.h>
#include <net.h>
#include <asm/io.h>
#include <netdev.h>
#include <fm_eth.h>
#include <fsl_mdio.h>
#include <malloc.h>
#include <asm/types.h>
#include <fsl_dtsec.h>
#include <asm/arch/soc.h>
#include <asm/arch-fsl-layerscape/config.h>
#include <asm/arch-fsl-layerscape/immap_lsch2.h>
#include <asm/arch/fsl_serdes.h>
#include <linux/delay.h>
#include <net/pfe_eth/pfe_eth.h>
#include <dm/platform_data/pfe_dm_eth.h>
#include <i2c.h>
#define DEFAULT_PFE_MDIO_NAME "PFE_MDIO"
static inline void ls1012ardb_reset_phy(void)
{
#ifdef CONFIG_TARGET_LS1012ARDB
/* Through reset IO expander reset both RGMII and SGMII PHYs */
#if CONFIG_IS_ENABLED(DM_I2C)
struct udevice *dev;
int ret;
/*
* The I2C IO-expander PCAL9555A is mouted on I2C1 bus(bus number is 0).
*/
ret = i2c_get_chip_for_busnum(0, I2C_MUX_IO2_ADDR,
1, &dev);
if (ret) {
printf("%s: Cannot find udev for a bus %d\n", __func__,
0);
return;
}
/* Config port 0
* - config pin IOXP_RST_ETH1_B and IOXP_RST_ETH2_B
* are enabled as an output.
*/
dm_i2c_reg_write(dev, 6, __PHY_MASK);
/*
* Set port 0 output a value to reset ETH2 interface
* - pin IOXP_RST_ETH2_B output 0b0
*/
dm_i2c_reg_write(dev, 2, __PHY_ETH2_MASK);
mdelay(10);
dm_i2c_reg_write(dev, 2, __PHY_ETH1_MASK);
/*
* Set port 0 output a value to reset ETH1 interface
* - pin IOXP_RST_ETH1_B output 0b0
*/
mdelay(10);
dm_i2c_reg_write(dev, 2, 0xFF);
#else
i2c_reg_write(I2C_MUX_IO2_ADDR, 6, __PHY_MASK);
i2c_reg_write(I2C_MUX_IO2_ADDR, 2, __PHY_ETH2_MASK);
mdelay(10);
i2c_reg_write(I2C_MUX_IO2_ADDR, 2, __PHY_ETH1_MASK);
mdelay(10);
i2c_reg_write(I2C_MUX_IO2_ADDR, 2, 0xFF);
#endif
mdelay(50);
#endif
}
int pfe_eth_board_init(struct udevice *dev)
{
static int init_done;
struct mii_dev *bus;
struct pfe_mdio_info mac_mdio_info;
struct pfe_eth_dev *priv = dev_get_priv(dev);
struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
int srds_s1 = in_be32(&gur->rcwsr[4]) &
FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
if (!init_done) {
ls1012ardb_reset_phy();
mac_mdio_info.reg_base = (void *)EMAC1_BASE_ADDR;
mac_mdio_info.name = DEFAULT_PFE_MDIO_NAME;
bus = pfe_mdio_init(&mac_mdio_info);
if (!bus) {
printf("Failed to register mdio\n");
return -1;
}
init_done = 1;
}
pfe_set_mdio(priv->gemac_port,
miiphy_get_dev_by_name(DEFAULT_PFE_MDIO_NAME));
switch (srds_s1) {
case 0x3508:
if (!priv->gemac_port) {
/* MAC1 */
pfe_set_phy_address_mode(priv->gemac_port,
CONFIG_PFE_EMAC1_PHY_ADDR,
PHY_INTERFACE_MODE_SGMII);
} else {
/* MAC2 */
pfe_set_phy_address_mode(priv->gemac_port,
CONFIG_PFE_EMAC2_PHY_ADDR,
PHY_INTERFACE_MODE_RGMII_ID);
}
break;
case 0x2208:
if (!priv->gemac_port) {
/* MAC1 */
pfe_set_phy_address_mode(priv->gemac_port,
CONFIG_PFE_EMAC1_PHY_ADDR,
PHY_INTERFACE_MODE_SGMII_2500);
} else {
/* MAC2 */
pfe_set_phy_address_mode(priv->gemac_port,
CONFIG_PFE_EMAC2_PHY_ADDR,
PHY_INTERFACE_MODE_SGMII_2500);
}
break;
default:
printf("unsupported SerDes PRCTL= %d\n", srds_s1);
break;
}
return 0;
}
static struct pfe_eth_pdata pfe_pdata0 = {
.pfe_eth_pdata_mac = {
.iobase = (phys_addr_t)EMAC1_BASE_ADDR,
.phy_interface = 0,
},
.pfe_ddr_addr = {
.ddr_pfe_baseaddr = (void *)CONFIG_DDR_PFE_BASEADDR,
.ddr_pfe_phys_baseaddr = CONFIG_DDR_PFE_PHYS_BASEADDR,
},
};
static struct pfe_eth_pdata pfe_pdata1 = {
.pfe_eth_pdata_mac = {
.iobase = (phys_addr_t)EMAC2_BASE_ADDR,
.phy_interface = 1,
},
.pfe_ddr_addr = {
.ddr_pfe_baseaddr = (void *)CONFIG_DDR_PFE_BASEADDR,
.ddr_pfe_phys_baseaddr = CONFIG_DDR_PFE_PHYS_BASEADDR,
},
};
U_BOOT_DRVINFO(ls1012a_pfe0) = {
.name = "pfe_eth",
.plat = &pfe_pdata0,
};
U_BOOT_DRVINFO(ls1012a_pfe1) = {
.name = "pfe_eth",
.plat = &pfe_pdata1,
};