blob: 8d1d45de5a7d1e0d4c6de33d93ef582ae609c823 [file] [log] [blame]
/*
* (C) Copyright 2006, 2007 Detlev Zundel, dzu@denx.de
* (C) Copyright 2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC852T 1
#define CONFIG_NC650 1
#define CONFIG_SYS_TEXT_BASE 0x40700000
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE 115200
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
/*
* 10 MHz - PLL input clock
*/
#define CONFIG_8xx_OSCLK 10000000
/*
* 50 MHz - default CPU clock
*/
#define CONFIG_8xx_CPUCLK_DEFAULT 50000000
/*
* 15 MHz - CPU minimum clock
*/
#define CONFIG_SYS_8xx_CPUCLK_MIN 15000000
/*
* 133 MHz - CPU maximum clock
*/
#define CONFIG_SYS_8xx_CPUCLK_MAX 133000000
#define CONFIG_SYS_MEASURE_CPUCLK
#define CONFIG_SYS_8XX_XIN CONFIG_8xx_OSCLK
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_AUTOBOOT_KEYED
#define CONFIG_AUTOBOOT_PROMPT \
"\nEnter password - autoboot in %d seconds...\n", bootdelay
#define CONFIG_AUTOBOOT_DELAY_STR "ids"
#define CONFIG_BOOT_RETRY_TIME 900
#define CONFIG_BOOT_RETRY_MIN 30
#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
"bootp;" \
"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
"bootm"
#define CONFIG_WATCHDOG /* watchdog enabled */
#undef CONFIG_STATUS_LED /* Status LED disabled */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_FEC_ENET 1 /* use FEC ethernet */
#define FEC_ENET
#define CONFIG_MII
#define CONFIG_SYS_DISCOVER_PHY 1
/* enable I2C and select the hardware/software driver */
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7f
/*
* Software (bit-bang) I2C driver configuration
*/
#if defined(CONFIG_IDS852_REV1)
#define SCL 0x1000 /* PA 3 */
#define SDA 0x2000 /* PA 2 */
#define __I2C_DIR immr->im_ioport.iop_padir
#define __I2C_DAT immr->im_ioport.iop_padat
#define __I2C_PAR immr->im_ioport.iop_papar
#elif defined(CONFIG_IDS852_REV2)
#define SCL 0x0002 /* PB 30 */
#define SDA 0x0001 /* PB 31 */
#define __I2C_PAR immr->im_cpm.cp_pbpar
#define __I2C_DIR immr->im_cpm.cp_pbdir
#define __I2C_DAT immr->im_cpm.cp_pbdat
#endif
#define I2C_INIT { __I2C_PAR &= ~(SDA|SCL); \
__I2C_DIR |= (SDA|SCL); }
#define I2C_READ ((__I2C_DAT & SDA) ? 1 : 0)
#define I2C_SDA(x) { if (x) __I2C_DAT |= SDA; else __I2C_DAT &= ~SDA; }
#define I2C_SCL(x) { if (x) __I2C_DAT |= SCL; else __I2C_DAT &= ~SCL; }
#define I2C_DELAY { udelay(5); }
#define I2C_ACTIVE { __I2C_DIR |= SDA; }
#define I2C_TRISTATE { __I2C_DIR &= ~SDA; }
#define CONFIG_RTC_PCF8563
#define CONFIG_SYS_I2C_RTC_ADDR 0x51
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_I2C
#define CONFIG_CMD_NAND
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_NFS
#define CONFIG_CMD_SNTP
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x00100000
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CONFIG_SYS_IMMR 0xF0000000
#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024))
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_FLASH_BASE 0x40000000
#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_OFFSET 0x00740000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment sector */
#define CONFIG_ENV_SIZE 0x4000 /* Used Size of Environment Sector */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*
* NAND flash support
*/
#define CONFIG_SYS_MAX_NAND_DEVICE 1
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
*/
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | \
SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \
SCCR_DFLCD000 | SCCR_DFALCD00)
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
#define CONFIG_SYS_DER 0
/*
* Init Memory Controller:
*
* BR0 and OR0 (FLASH)
*/
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
/* FLASH timing: Default value of OR0 after reset */
#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
OR_SCY_15_CLK | OR_TRLX)
#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V)
/*
* BR2 and OR2 (NAND Flash) - addressed through UPMB on rev 1
* rev2 only uses the chipselect
*/
#define CONFIG_SYS_NAND_BASE 0x50000000
#define CONFIG_SYS_NAND_SIZE 0x04000000
#define CONFIG_SYS_OR_TIMING_NAND (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
OR_SCY_15_CLK | OR_EHTR | OR_TRLX)
#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_NAND_BASE & BR_BA_MSK) | BR_PS_8 | BR_MS_UPMB | BR_V )
#define CONFIG_SYS_OR2_PRELIM (((-CONFIG_SYS_NAND_SIZE) & OR_AM_MSK) | OR_BI )
/*
* BR3 and OR3 (SDRAM)
*/
#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
/*
* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)
*/
#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
#define CONFIG_SYS_OR3_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM)
#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V)
/*
* BR4 and OR4 (CPLD)
*/
#define CONFIG_SYS_CPLD_BASE 0x80000000 /* CPLD */
#define CONFIG_SYS_CPLD_SIZE 0x10000 /* only 16 used */
#define CONFIG_SYS_OR_TIMING_CPLD (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
OR_SCY_1_CLK)
#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_CPLD_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
#define CONFIG_SYS_OR4_PRELIM (((-CONFIG_SYS_CPLD_SIZE) & OR_AM_MSK) | CONFIG_SYS_OR_TIMING_CPLD)
/*
* BR5 and OR5 (SRAM)
*/
#define CONFIG_SYS_SRAM_BASE 0x60000000
#define CONFIG_SYS_SRAM_SIZE 0x00080000
#define CONFIG_SYS_OR_TIMING_SRAM (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
OR_SCY_15_CLK | OR_EHTR | OR_TRLX)
#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_SRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
#define CONFIG_SYS_OR5_PRELIM (((-CONFIG_SYS_SRAM_SIZE) & OR_AM_MSK) | CONFIG_SYS_OR_TIMING_SRAM)
#if defined(CONFIG_CP850)
/*
* BR6 and OR6 (DPRAM) - only on CP850
*/
#define CONFIG_SYS_OR6_PRELIM 0xffff8170
#define CONFIG_SYS_BR6_PRELIM 0xa0000401
#define DPRAM_BASE_ADDR 0xa0000000
#define CONFIG_MISC_INIT_R 1
#endif
/*
* 4096 Rows from SDRAM example configuration
* 1000 factor s -> ms
* 64 PTP (pre-divider from MPTPR) from SDRAM example configuration
* 4 Number of refresh cycles per period
* 64 Refresh cycle in ms per number of rows
*/
#define CONFIG_SYS_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
/*
* Memory Periodic Timer Prescaler
*/
/* periodic timer for refresh */
#define CONFIG_SYS_MAMR_PTA 39
/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
/*
* MAMR settings for SDRAM
*/
#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/*
* MBMR settings for NAND flash
*/
#define CONFIG_SYS_MBMR_NAND ( MBMR_WLFB_5X )
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */
/*
* JFFS2 partitions
*/
/* No command line, one static partition */
#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nand0"
#define CONFIG_JFFS2_PART_SIZE 0x00400000
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/* mtdparts command line support */
#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nor0=nc650-0,nand0=nc650-nand"
#define MTDPARTS_DEFAULT "mtdparts=nc650-0:1m(kernel1),1m(kernel2)," \
"4m(cramfs1),1m(cramfs2)," \
"256k(u-boot),128k(env);" \
"nc650-nand:4m(jffs1),28m(jffs2)"
#endif /* __CONFIG_H */