blob: 00456a7003db9d646234a4b797a815cdac27ce90 [file] [log] [blame]
/*
* (C) Copyright 2005
* Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <command.h>
#include <malloc.h>
DECLARE_GLOBAL_DATA_PTR;
int board_early_init_f (void)
{
unsigned long CPC0_CR0Reg;
/*
* Setup GPIO pins
*/
CPC0_CR0Reg = mfdcr(CPC0_CR0);
mtdcr(CPC0_CR0, CPC0_CR0Reg |
((CONFIG_SYS_EEPROM_WP | CONFIG_SYS_PB_LED |
CONFIG_SYS_SELF_RST | CONFIG_SYS_INTA_FAKE) << 5));
/* set output pins to high */
out_be32((void *)GPIO0_OR, CONFIG_SYS_EEPROM_WP);
/* setup for output (LED=off) */
out_be32((void *)GPIO0_TCR, CONFIG_SYS_EEPROM_WP | CONFIG_SYS_PB_LED);
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
* IRQ 16 405GP internally generated; active low; level sensitive
* IRQ 17-24 RESERVED
* IRQ 25 (EXT IRQ 0) PB0; active low; level sensitive
* IRQ 26 (EXT IRQ 1) PB1; active low; level sensitive
* IRQ 27 (EXT IRQ 2) PCI SLOT 0; active low; level sensitive
* IRQ 28 (EXT IRQ 3) PCI SLOT 1; active low; level sensitive
* IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive
* IRQ 30 (EXT IRQ 5) PCI SLOT 3; active low; level sensitive
* IRQ 31 (EXT IRQ 6) unused
*/
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
mtdcr(UIC0ER, 0x00000000); /* disable all ints */
mtdcr(UIC0CR, 0x00000000); /* set all to be non-critical*/
mtdcr(UIC0PR, 0xFFFFFF81); /* set int polarities */
mtdcr(UIC0TR, 0x10000000); /* set int trigger levels */
mtdcr(UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority*/
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
return 0;
}
int misc_init_r (void)
{
unsigned long CPC0_CR0Reg;
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
gd->bd->bi_flashoffset = 0;
/*
* Select cts (and not dsr) on uart1
*/
CPC0_CR0Reg = mfdcr(CPC0_CR0);
mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00001000);
return (0);
}
/*
* Check Board Identity:
*/
int checkboard (void)
{
char str[64];
int i = getenv_r ("serial#", str, sizeof(str));
puts ("Board: ");
if (i == -1) {
puts ("### No HW ID - assuming CPCI2DP");
} else {
puts(str);
}
printf(" (Ver 1.0)");
putc ('\n');
return 0;
}
#if defined(CONFIG_SYS_EEPROM_WREN)
/* Input: <dev_addr> I2C address of EEPROM device to enable.
* <state> -1: deliver current state
* 0: disable write
* 1: enable write
* Returns: -1: wrong device address
* 0: dis-/en- able done
* 0/1: current state if <state> was -1.
*/
int eeprom_write_enable (unsigned dev_addr, int state) {
if (CONFIG_SYS_I2C_EEPROM_ADDR != dev_addr) {
return -1;
} else {
switch (state) {
case 1:
/* Enable write access, clear bit GPIO_SINT2. */
out_be32((void *)GPIO0_OR,
in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_EEPROM_WP);
state = 0;
break;
case 0:
/* Disable write access, set bit GPIO_SINT2. */
out_be32((void *)GPIO0_OR,
in_be32((void *)GPIO0_OR) | CONFIG_SYS_EEPROM_WP);
state = 0;
break;
default:
/* Read current status back. */
state = (0 == (in_be32((void *)GPIO0_OR) &
CONFIG_SYS_EEPROM_WP));
break;
}
}
return state;
}
#endif
#if defined(CONFIG_SYS_EEPROM_WREN)
int do_eep_wren (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
int query = argc == 1;
int state = 0;
if (query) {
/* Query write access state. */
state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, -1);
if (state < 0) {
puts ("Query of write access state failed.\n");
} else {
printf ("Write access for device 0x%0x is %sabled.\n",
CONFIG_SYS_I2C_EEPROM_ADDR, state ? "en" : "dis");
state = 0;
}
} else {
if ('0' == argv[1][0]) {
/* Disable write access. */
state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, 0);
} else {
/* Enable write access. */
state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, 1);
}
if (state < 0) {
puts ("Setup of write access state failed.\n");
}
}
return state;
}
U_BOOT_CMD(
eepwren, 2, 0, do_eep_wren,
"Enable / disable / query EEPROM write access",
""
);
#endif /* #if defined(CONFIG_SYS_EEPROM_WREN) */