| menu "LED Support" |
| |
| config LED |
| bool "Enable LED support" |
| depends on DM |
| help |
| Many boards have LEDs which can be used to signal status or alerts. |
| U-Boot provides a uclass API to implement this feature. LED drivers |
| can provide access to board-specific LEDs. Use of the device tree |
| for configuration is encouraged. |
| |
| config LED_BCM6328 |
| bool "LED Support for BCM6328" |
| depends on LED && ARCH_BMIPS |
| help |
| This option enables support for LEDs connected to the BCM6328 |
| LED HW controller accessed via MMIO registers. |
| HW blinking is supported and up to 24 LEDs can be controlled. |
| All LEDs can blink at the same time but the delay is shared, which |
| means that if one LED is set to blink at 100ms and then a different |
| LED is set to blink at 200ms, both will blink at 200ms. |
| |
| config LED_BCM6358 |
| bool "LED Support for BCM6358" |
| depends on LED && ARCH_BMIPS |
| help |
| This option enables support for LEDs connected to the BCM6358 |
| LED HW controller accessed via MMIO registers. |
| HW has no blinking capabilities and up to 32 LEDs can be controlled. |
| |
| config LED_BCM6858 |
| bool "LED Support for BCM6858" |
| depends on LED && (ARCH_BCM68360 || ARCH_BCM6858 || ARCH_BCM63158) |
| help |
| This option enables support for LEDs connected to the BCM6858 |
| HW has blinking capabilities and up to 32 LEDs can be controlled. |
| |
| config LED_CORTINA |
| bool "LED Support for Cortina Access CAxxxx SoCs" |
| depends on LED && (CORTINA_PLATFORM) |
| help |
| This option enables support for LEDs connected to the Cortina |
| Access CAxxxx SOCs. |
| |
| |
| config LED_BLINK |
| bool "Support LED blinking" |
| depends on LED |
| help |
| Some drivers can support automatic blinking of LEDs with a given |
| period, without needing timers or extra code to handle the timing. |
| This option enables support for this which adds slightly to the |
| code size. |
| |
| config SPL_LED |
| bool "Enable LED support in SPL" |
| depends on SPL && SPL_DM |
| help |
| The LED subsystem adds a small amount of overhead to the image. |
| If this is acceptable and you have a need to use LEDs in SPL, |
| enable this option. You will need to enable device tree in SPL |
| for this to work. |
| |
| config LED_GPIO |
| bool "LED support for GPIO-connected LEDs" |
| depends on LED && DM_GPIO |
| help |
| Enable support for LEDs which are connected to GPIO lines. These |
| GPIOs may be on the SoC or some other device which provides GPIOs. |
| The GPIO driver must used driver model. LEDs are configured using |
| the device tree. |
| |
| config SPL_LED_GPIO |
| bool "LED support for GPIO-connected LEDs in SPL" |
| depends on SPL_LED && DM_GPIO |
| help |
| This option is an SPL-variant of the LED_GPIO option. |
| See the help of LED_GPIO for details. |
| |
| config LED_STATUS |
| bool "Enable status LED API" |
| help |
| Allows common u-boot commands to use a board's leds to |
| provide status for activities like booting and downloading files. |
| |
| if LED_STATUS |
| |
| # Hidden constants |
| |
| config LED_STATUS_OFF |
| int |
| default 0 |
| |
| config LED_STATUS_BLINKING |
| int |
| default 1 |
| |
| config LED_STATUS_ON |
| int |
| default 2 |
| |
| # Hidden constants end |
| |
| config LED_STATUS_GPIO |
| bool "GPIO status LED implementation" |
| help |
| The status LED can be connected to a GPIO pin. In such cases, the |
| gpio_led driver can be used as a status LED backend implementation. |
| |
| config LED_STATUS_BOARD_SPECIFIC |
| bool "Specific board" |
| default y |
| help |
| LED support is only for a specific board. |
| |
| comment "LEDs parameters" |
| |
| config LED_STATUS0 |
| bool "Enable status LED 0" |
| |
| if LED_STATUS0 |
| |
| config LED_STATUS_BIT |
| int "identification" |
| help |
| CONFIG_LED_STATUS_BIT is passed into the __led_* functions to identify |
| which LED is being acted on. As such, the chosen value must be unique |
| with respect to the other CONFIG_LED_STATUS_BIT's. Mapping the value |
| to a physical LED is the responsibility of the __led_* function. |
| |
| config LED_STATUS_STATE |
| int "initial state" |
| range LED_STATUS_OFF LED_STATUS_ON |
| default LED_STATUS_OFF |
| help |
| Should be set one of the following: |
| 0 - off |
| 1 - blinking |
| 2 - on |
| |
| config LED_STATUS_FREQ |
| int "blink frequency" |
| range 2 10 |
| default 2 |
| help |
| The LED blink period calculated from LED_STATUS_FREQ: |
| LED_STATUS_PERIOD = CONFIG_SYS_HZ/LED_STATUS_FREQ |
| Values range: 2 - 10 |
| |
| endif # LED_STATUS0 |
| |
| config LED_STATUS1 |
| bool "Enable status LED 1" |
| |
| if LED_STATUS1 |
| |
| config LED_STATUS_BIT1 |
| int "identification" |
| help |
| CONFIG_LED_STATUS_BIT1 is passed into the __led_* functions to |
| identify which LED is being acted on. As such, the chosen value must |
| be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping |
| the value to a physical LED is the responsibility of the __led_* |
| function. |
| |
| config LED_STATUS_STATE1 |
| int "initial state" |
| range LED_STATUS_OFF LED_STATUS_ON |
| default LED_STATUS_OFF |
| help |
| Should be set one of the following: |
| 0 - off |
| 1 - blinking |
| 2 - on |
| |
| config LED_STATUS_FREQ1 |
| int "blink frequency" |
| range 2 10 |
| default 2 |
| help |
| The LED blink period calculated from LED_STATUS_FREQ1: |
| LED_STATUS_PERIOD1 = CONFIG_SYS_HZ/LED_STATUS_FREQ1 |
| Values range: 2 - 10 |
| |
| endif # LED_STATUS1 |
| |
| config LED_STATUS2 |
| bool "Enable status LED 2" |
| |
| if LED_STATUS2 |
| |
| config LED_STATUS_BIT2 |
| int "identification" |
| help |
| CONFIG_LED_STATUS_BIT2 is passed into the __led_* functions to |
| identify which LED is being acted on. As such, the chosen value must |
| be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping |
| the value to a physical LED is the responsibility of the __led_* |
| function. |
| |
| config LED_STATUS_STATE2 |
| int "initial state" |
| range LED_STATUS_OFF LED_STATUS_ON |
| default LED_STATUS_OFF |
| help |
| Should be set one of the following: |
| 0 - off |
| 1 - blinking |
| 2 - on |
| |
| config LED_STATUS_FREQ2 |
| int "blink frequency" |
| range 2 10 |
| default 2 |
| help |
| The LED blink period calculated from LED_STATUS_FREQ2: |
| LED_STATUS_PERIOD2 = CONFIG_SYS_HZ/LED_STATUS_FREQ2 |
| Values range: 2 - 10 |
| |
| endif # LED_STATUS2 |
| |
| config LED_STATUS3 |
| bool "Enable status LED 3" |
| |
| if LED_STATUS3 |
| |
| config LED_STATUS_BIT3 |
| int "identification" |
| help |
| CONFIG_LED_STATUS_BIT3 is passed into the __led_* functions to |
| identify which LED is being acted on. As such, the chosen value must |
| be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping |
| the value to a physical LED is the responsibility of the __led_* |
| function. |
| |
| config LED_STATUS_STATE3 |
| int "initial state" |
| range LED_STATUS_OFF LED_STATUS_ON |
| default LED_STATUS_OFF |
| help |
| Should be set one of the following: |
| 0 - off |
| 1 - blinking |
| 2 - on |
| |
| config LED_STATUS_FREQ3 |
| int "blink frequency" |
| range 2 10 |
| default 2 |
| help |
| The LED blink period calculated from LED_STATUS_FREQ3: |
| LED_STATUS_PERIOD3 = CONFIG_SYS_HZ/LED_STATUS_FREQ3 |
| Values range: 2 - 10 |
| |
| endif # LED_STATUS3 |
| |
| config LED_STATUS4 |
| bool "Enable status LED 4" |
| |
| if LED_STATUS4 |
| |
| config LED_STATUS_BIT4 |
| int "identification" |
| help |
| CONFIG_LED_STATUS_BIT4 is passed into the __led_* functions to |
| identify which LED is being acted on. As such, the chosen value must |
| be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping |
| the value to a physical LED is the responsibility of the __led_* |
| function. |
| |
| config LED_STATUS_STATE4 |
| int "initial state" |
| range LED_STATUS_OFF LED_STATUS_ON |
| default LED_STATUS_OFF |
| help |
| Should be set one of the following: |
| 0 - off |
| 1 - blinking |
| 2 - on |
| |
| config LED_STATUS_FREQ4 |
| int "blink frequency" |
| range 2 10 |
| default 2 |
| help |
| The LED blink period calculated from LED_STATUS_FREQ4: |
| LED_STATUS_PERIOD4 = CONFIG_SYS_HZ/LED_STATUS_FREQ4 |
| Values range: 2 - 10 |
| |
| endif # LED_STATUS4 |
| |
| config LED_STATUS5 |
| bool "Enable status LED 5" |
| |
| if LED_STATUS5 |
| |
| config LED_STATUS_BIT5 |
| int "identification" |
| help |
| CONFIG_LED_STATUS_BIT5 is passed into the __led_* functions to |
| identify which LED is being acted on. As such, the chosen value must |
| be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping |
| the value to a physical LED is the responsibility of the __led_* |
| function. |
| |
| config LED_STATUS_STATE5 |
| int "initial state" |
| range LED_STATUS_OFF LED_STATUS_ON |
| default LED_STATUS_OFF |
| help |
| Should be set one of the following: |
| 0 - off |
| 1 - blinking |
| 2 - on |
| |
| config LED_STATUS_FREQ5 |
| int "blink frequency" |
| range 2 10 |
| default 2 |
| help |
| The LED blink period calculated from LED_STATUS_FREQ5: |
| LED_STATUS_PERIOD5 = CONFIG_SYS_HZ/LED_STATUS_FREQ5 |
| Values range: 2 - 10 |
| |
| endif # LED_STATUS5 |
| |
| config LED_STATUS_BOOT_ENABLE |
| bool "Enable BOOT LED" |
| help |
| Enable to turn an LED on when the board is booting. |
| |
| if LED_STATUS_BOOT_ENABLE |
| |
| config LED_STATUS_BOOT |
| int "LED to light when the board is booting" |
| help |
| Valid enabled LED device number. |
| |
| endif # LED_STATUS_BOOT_ENABLE |
| |
| config LED_STATUS_RED_ENABLE |
| bool "Enable red LED" |
| help |
| Enable red status LED. |
| |
| if LED_STATUS_RED_ENABLE |
| |
| config LED_STATUS_RED |
| int "Red LED identification" |
| help |
| Valid enabled LED device number. |
| |
| endif # LED_STATUS_RED_ENABLE |
| |
| config LED_STATUS_YELLOW_ENABLE |
| bool "Enable yellow LED" |
| help |
| Enable yellow status LED. |
| |
| if LED_STATUS_YELLOW_ENABLE |
| |
| config LED_STATUS_YELLOW |
| int "Yellow LED identification" |
| help |
| Valid enabled LED device number. |
| |
| endif # LED_STATUS_YELLOW_ENABLE |
| |
| config LED_STATUS_BLUE_ENABLE |
| bool "Enable blue LED" |
| help |
| Enable blue status LED. |
| |
| if LED_STATUS_BLUE_ENABLE |
| |
| config LED_STATUS_BLUE |
| int "Blue LED identification" |
| help |
| Valid enabled LED device number. |
| |
| endif # LED_STATUS_BLUE_ENABLE |
| |
| config LED_STATUS_GREEN_ENABLE |
| bool "Enable green LED" |
| help |
| Enable green status LED. |
| |
| if LED_STATUS_GREEN_ENABLE |
| |
| config LED_STATUS_GREEN |
| int "Green LED identification" |
| help |
| Valid enabled LED device number (0-5). |
| |
| endif # LED_STATUS_GREEN_ENABLE |
| |
| config LED_STATUS_CMD |
| bool "Enable status LED commands" |
| |
| endif # LED_STATUS |
| |
| endmenu |