blob: eadccc182aa1e5871aa232a191ee208c49086229 [file] [log] [blame]
/*
* Configuration settings for the SAMA5D4EK board.
*
* Copyright (C) 2014 Atmel
* Bo Shen <voice.shen@atmel.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* No NOR flash, this definition should put before common header */
#define CONFIG_SYS_NO_FLASH
#include "at91-sama5_common.h"
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_USART3
#define CONFIG_USART_ID ATMEL_ID_USART3
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
#define CONFIG_SYS_SDRAM_SIZE 0x20000000
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_INIT_SP_ADDR 0x210000
#else
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
/* SerialFlash */
#define CONFIG_CMD_SF
#ifdef CONFIG_CMD_SF
#define CONFIG_ATMEL_SPI
#define CONFIG_ATMEL_SPI0
#define CONFIG_SPI_FLASH_ATMEL
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 30000000
#endif
/* NAND flash */
#define CONFIG_CMD_NAND
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* PMECC & PMERRLOC */
#define CONFIG_ATMEL_NAND_HWECC
#define CONFIG_ATMEL_NAND_HW_PMECC
#endif
/* MMC */
#define CONFIG_CMD_MMC
#ifdef CONFIG_CMD_MMC
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_GENERIC_ATMEL_MCI
#define ATMEL_BASE_MMCI ATMEL_BASE_MCI1
#endif
/* USB */
#define CONFIG_CMD_USB
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_USB_STORAGE
#endif
/* USB device */
#define CONFIG_USB_GADGET
#define CONFIG_USB_GADGET_DUALSPEED
#define CONFIG_USB_GADGET_ATMEL_USBA
#define CONFIG_USB_ETHER
#define CONFIG_USB_ETH_RNDIS
#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D4EK"
#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif
/* Ethernet Hardware */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_MACB_SEARCH_PHY
/* LCD */
#define CONFIG_LCD
#define LCD_BPP LCD_COLOR16
#define LCD_OUTPUT_BPP 18
#define CONFIG_LCD_LOGO
#define CONFIG_LCD_INFO
#define CONFIG_LCD_INFO_BELOW_LOGO
#define CONFIG_SYS_WHITE_ON_BLACK
#define CONFIG_ATMEL_HLCD
#define CONFIG_ATMEL_LCD_RGB565
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#ifdef CONFIG_SYS_USE_SERIALFLASH
/* bootstrap + u-boot + env + linux in serial flash */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_OFFSET 0x10000
#define CONFIG_ENV_SIZE 0x10000
#define CONFIG_ENV_SECT_SIZE 0x1000
#define CONFIG_BOOTCOMMAND "sf probe 0; " \
"sf read 0x21000000 0xa0000 0x60000; " \
"sf read 0x22000000 0x100000 0x300000; " \
"bootz 0x22000000 - 0x21000000"
#elif CONFIG_SYS_USE_NANDFLASH
/* bootstrap + u-boot + env in nandflash */
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0xc0000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
#define CONFIG_ENV_SIZE 0x20000
#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \
"nand read 0x22000000 0x200000 0x600000;" \
"bootz 0x22000000 - 0x21000000"
#elif CONFIG_SYS_USE_MMC
/* bootstrap + u-boot + env in sd card */
#define CONFIG_ENV_IS_IN_FAT
#define CONFIG_FAT_WRITE
#define FAT_ENV_INTERFACE "mmc"
/*
* We don't specify the part number, if device 0 has partition table, it means
* the first partition; it no partition table, then take whole device as a
* FAT file system.
*/
#define FAT_ENV_DEVICE_AND_PART "0"
#define FAT_ENV_FILE "uboot.env"
#define CONFIG_ENV_SIZE 0x4000
#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 sama5d4ek.dtb; " \
"fatload mmc 0:1 0x22000000 zImage; " \
"bootz 0x22000000 - 0x21000000"
#endif
/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x200000
#define CONFIG_SPL_MAX_SIZE 0x10000
#define CONFIG_SPL_BSS_START_ADDR 0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
#elif CONFIG_SYS_USE_NANDFLASH
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
#define CONFIG_PMECC_CAP 8
#define CONFIG_PMECC_SECTOR_SIZE 512
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE 0x1000
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_OOBSIZE 224
#define CONFIG_SYS_NAND_BLOCK_SIZE 0x40000
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
#elif CONFIG_SYS_USE_SERIALFLASH
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
#endif
#endif