include/configs/M5253DEMO.h - platform/external/u-boot - Gitiles

 /* Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
  * Hayden Fraser (Hayden.Fraser@freescale.com)
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef _M5253DEMO_H
 #define _M5253DEMO_H

 #define CONFIG_M5253DEMO	/* define board type */

 #define CONFIG_MCFTMR

 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		(0)

 #undef CONFIG_WATCHDOG		/* disable watchdog */


 /* Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
  */
 #ifdef CONFIG_MONITOR_IS_IN_RAM
 #	define CONFIG_ENV_OFFSET		0x4000
 #	define CONFIG_ENV_SECT_SIZE	0x1000
 #else
 #	define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x4000)
 #	define CONFIG_ENV_SECT_SIZE	0x1000
 #endif

 #define LDS_BOARD_TEXT \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	env/embedded.o(.text*);

 /*
  * Command line configuration.
  */

 #ifdef CONFIG_IDE
 /* ATA */
 #	define CONFIG_IDE_RESET		1
 #	define CONFIG_IDE_PREINIT	1
 #	define CONFIG_ATAPI
 #	undef CONFIG_LBA48

 #	define CONFIG_SYS_IDE_MAXBUS		1
 #	define CONFIG_SYS_IDE_MAXDEVICE	2

 #	define CONFIG_SYS_ATA_BASE_ADDR	(CONFIG_SYS_MBAR2 + 0x800)
 #	define CONFIG_SYS_ATA_IDE0_OFFSET	0

 #	define CONFIG_SYS_ATA_DATA_OFFSET	0xA0	/* Offset for data I/O */
 #	define CONFIG_SYS_ATA_REG_OFFSET	0xA0	/* Offset for normal register accesses */
 #	define CONFIG_SYS_ATA_ALT_OFFSET	0xC0	/* Offset for alternate registers */
 #	define CONFIG_SYS_ATA_STRIDE		4	/* Interval between registers */
 #endif

 #define CONFIG_DRIVER_DM9000
 #ifdef CONFIG_DRIVER_DM9000
 #	define CONFIG_DM9000_BASE	(CONFIG_SYS_CS1_BASE | 0x300)
 #	define DM9000_IO		CONFIG_DM9000_BASE
 #	define DM9000_DATA		(CONFIG_DM9000_BASE + 4)
 #	undef CONFIG_DM9000_DEBUG
 #	define CONFIG_DM9000_BYTE_SWAPPED

 #	define CONFIG_OVERWRITE_ETHADDR_ONCE

 #	define CONFIG_EXTRA_ENV_SETTINGS		\
 		"netdev=eth0\0"				\
 		"inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0"	\
 		"loadaddr=10000\0"			\
 		"u-boot=u-boot.bin\0"			\
 		"load=tftp ${loadaddr) ${u-boot}\0"	\
 		"upd=run load; run prog\0"		\
 		"prog=prot off 0xff800000 0xff82ffff;"	\
 		"era 0xff800000 0xff82ffff;"		\
 		"cp.b ${loadaddr} 0xff800000 ${filesize};"	\
 		"save\0"				\
 		""
 #endif

 #define CONFIG_HOSTNAME		M5253DEMO

 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	80000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x00000280
 #define CONFIG_SYS_IMMR		CONFIG_SYS_MBAR
 #define CONFIG_SYS_I2C_PINMUX_REG	(*(u32 *) (CONFIG_SYS_MBAR+0x19C))
 #define CONFIG_SYS_I2C_PINMUX_CLR	(0xFFFFE7FF)
 #define CONFIG_SYS_I2C_PINMUX_SET	(0)

 #define CONFIG_SYS_LONGHELP		/* undef to save memory */

 #if defined(CONFIG_CMD_KGDB)
 #	define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
 #else
 #	define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS		16	/* max number of command args */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */

 #define CONFIG_SYS_LOAD_ADDR		0x00100000

 #define CONFIG_SYS_MEMTEST_START	0x400
 #define CONFIG_SYS_MEMTEST_END		0x380000

 #undef CONFIG_SYS_PLL_BYPASS		/* bypass PLL for test purpose */
 #define CONFIG_SYS_FAST_CLK
 #ifdef CONFIG_SYS_FAST_CLK
 #	define CONFIG_SYS_PLLCR	0x1243E054
 #	define CONFIG_SYS_CLK		140000000
 #else
 #	define CONFIG_SYS_PLLCR	0x135a4140
 #	define CONFIG_SYS_CLK		70000000
 #endif

 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  */

 #define CONFIG_SYS_MBAR		0x10000000	/* Register Base Addrs */
 #define CONFIG_SYS_MBAR2		0x80000000	/* Module Base Addrs 2 */

 /*
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR	0x20000000
 #define CONFIG_SYS_INIT_RAM_SIZE	0x10000	/* Size of used area in internal SRAM */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 /*
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_SDRAM_SIZE		16	/* SDRAM size in MB */

 #ifdef CONFIG_MONITOR_IS_IN_RAM
 #	define CONFIG_SYS_MONITOR_BASE	0x20000
 #else
 #	define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE + 0x400)
 #endif

 #define CONFIG_SYS_MONITOR_LEN		0x40000
 #define CONFIG_SYS_MALLOC_LEN		(256 << 10)
 #define CONFIG_SYS_BOOTPARAMS_LEN	(64*1024)

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
 #define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
 #define CONFIG_SYS_BOOTM_LEN		(CONFIG_SYS_SDRAM_SIZE << 20)

 /* FLASH organization */
 #define CONFIG_SYS_FLASH_BASE		(CONFIG_SYS_CS0_BASE)
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	2048	/* max number of sectors on one chip */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	1000

 #define FLASH_SST6401B		0x200
 #define SST_ID_xF6401B		0x236D236D

 #undef CONFIG_SYS_FLASH_CFI
 #ifdef CONFIG_SYS_FLASH_CFI
 /*
  * Unable to use CFI driver, due to incompatible sector erase command by SST.
  * Amd/Atmel use 0x30 for sector erase, SST use 0x50.
  * 0x30 is block erase in SST
  */
 #	define CONFIG_FLASH_CFI_DRIVER	1
 #	define CONFIG_SYS_FLASH_SIZE		0x800000
 #	define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
 #	define CONFIG_FLASH_CFI_LEGACY
 #else
 #	define CONFIG_SYS_SST_SECT		2048
 #	define CONFIG_SYS_SST_SECTSZ		0x1000
 #	define CONFIG_SYS_FLASH_WRITE_TOUT	500
 #endif

 /* Cache Configuration */
 #define CONFIG_SYS_CACHELINE_SIZE	16

 #define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - 8)
 #define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - 4)
 #define CONFIG_SYS_ICACHE_INV		(CF_CACR_DCM)
 #define CONFIG_SYS_CACHE_ACR0		(CONFIG_SYS_FLASH_BASE | \
 					 CF_ADDRMASK(8) | \
 					 CF_ACR_EN | CF_ACR_SM_ALL)
 #define CONFIG_SYS_CACHE_ACR1		(CONFIG_SYS_SDRAM_BASE | \
 					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 					 CF_ACR_EN | CF_ACR_SM_ALL)
 #define CONFIG_SYS_CACHE_ICACR		(CF_CACR_CENB | CF_CACR_CEIB | \
 					 CF_CACR_DBWE)

 /* Port configuration */
 #define CONFIG_SYS_FECI2C		0xF0

 #define CONFIG_SYS_CS0_BASE		0xFF800000
 #define CONFIG_SYS_CS0_MASK		0x007F0021
 #define CONFIG_SYS_CS0_CTRL		0x00001D80

 #define CONFIG_SYS_CS1_BASE		0xE0000000
 #define CONFIG_SYS_CS1_MASK		0x00000001
 #define CONFIG_SYS_CS1_CTRL		0x00003DD8

 /*-----------------------------------------------------------------------
  * Port configuration
  */
 #define CONFIG_SYS_GPIO_FUNC		0x00000008	/* Set gpio pins: none */
 #define CONFIG_SYS_GPIO1_FUNC		0x00df00f0	/* 36-39(SWITCH),48-52(FPGAs),54 */
 #define CONFIG_SYS_GPIO_EN		0x00000008	/* Set gpio output enable */
 #define CONFIG_SYS_GPIO1_EN		0x00c70000	/* Set gpio output enable */
 #define CONFIG_SYS_GPIO_OUT		0x00000008	/* Set outputs to default state */
 #define CONFIG_SYS_GPIO1_OUT		0x00c70000	/* Set outputs to default state */
 #define CONFIG_SYS_GPIO1_LED		0x00400000	/* user led */

 #endif				/* _M5253DEMO_H */
	/* Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
	* Hayden Fraser (Hayden.Fraser@freescale.com)
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef _M5253DEMO_H
	#define _M5253DEMO_H

	#define CONFIG_M5253DEMO /* define board type */

	#define CONFIG_MCFTMR

	#define CONFIG_MCFUART
	#define CONFIG_SYS_UART_PORT (0)

	#undef CONFIG_WATCHDOG /* disable watchdog */


	/* Configuration for environment
	* Environment is embedded in u-boot in the second sector of the flash
	*/
	#ifdef CONFIG_MONITOR_IS_IN_RAM
	# define CONFIG_ENV_OFFSET 0x4000
	# define CONFIG_ENV_SECT_SIZE 0x1000
	#else
	# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000)
	# define CONFIG_ENV_SECT_SIZE 0x1000
	#endif

	#define LDS_BOARD_TEXT \
	. = DEFINED(env_offset) ? env_offset : .; \
	env/embedded.o(.text*);

	/*
	* Command line configuration.
	*/

	#ifdef CONFIG_IDE
	/* ATA */
	# define CONFIG_IDE_RESET 1
	# define CONFIG_IDE_PREINIT 1
	# define CONFIG_ATAPI
	# undef CONFIG_LBA48

	# define CONFIG_SYS_IDE_MAXBUS 1
	# define CONFIG_SYS_IDE_MAXDEVICE 2

	# define CONFIG_SYS_ATA_BASE_ADDR (CONFIG_SYS_MBAR2 + 0x800)
	# define CONFIG_SYS_ATA_IDE0_OFFSET 0

	# define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */
	# define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */
	# define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */
	# define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */
	#endif

	#define CONFIG_DRIVER_DM9000
	#ifdef CONFIG_DRIVER_DM9000
	# define CONFIG_DM9000_BASE (CONFIG_SYS_CS1_BASE \| 0x300)
	# define DM9000_IO CONFIG_DM9000_BASE
	# define DM9000_DATA (CONFIG_DM9000_BASE + 4)
	# undef CONFIG_DM9000_DEBUG
	# define CONFIG_DM9000_BYTE_SWAPPED

	# define CONFIG_OVERWRITE_ETHADDR_ONCE

	# define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
	"loadaddr=10000\0" \
	"u-boot=u-boot.bin\0" \
	"load=tftp ${loadaddr) ${u-boot}\0" \
	"upd=run load; run prog\0" \
	"prog=prot off 0xff800000 0xff82ffff;" \
	"era 0xff800000 0xff82ffff;" \
	"cp.b ${loadaddr} 0xff800000 ${filesize};" \
	"save\0" \
	""
	#endif

	#define CONFIG_HOSTNAME M5253DEMO

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 80000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000280
	#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
	#define CONFIG_SYS_I2C_PINMUX_REG ((u32 ) (CONFIG_SYS_MBAR+0x19C))
	#define CONFIG_SYS_I2C_PINMUX_CLR (0xFFFFE7FF)
	#define CONFIG_SYS_I2C_PINMUX_SET (0)

	#define CONFIG_SYS_LONGHELP /* undef to save memory */

	#if defined(CONFIG_CMD_KGDB)
	# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_LOAD_ADDR 0x00100000

	#define CONFIG_SYS_MEMTEST_START 0x400
	#define CONFIG_SYS_MEMTEST_END 0x380000

	#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */
	#define CONFIG_SYS_FAST_CLK
	#ifdef CONFIG_SYS_FAST_CLK
	# define CONFIG_SYS_PLLCR 0x1243E054
	# define CONFIG_SYS_CLK 140000000
	#else
	# define CONFIG_SYS_PLLCR 0x135a4140
	# define CONFIG_SYS_CLK 70000000
	#endif

	/*
	* Low Level Configuration Settings
	* (address mappings, register initial values, etc.)
	* You should know what you are doing if you make changes here.
	*/

	#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */
	#define CONFIG_SYS_MBAR2 0x80000000 /* Module Base Addrs 2 */

	/*
	* Definitions for initial stack pointer and data area (in DPRAM)
	*/
	#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
	#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	/*
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
	*/
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */

	#ifdef CONFIG_MONITOR_IS_IN_RAM
	# define CONFIG_SYS_MONITOR_BASE 0x20000
	#else
	# define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
	#endif

	#define CONFIG_SYS_MONITOR_LEN 0x40000
	#define CONFIG_SYS_MALLOC_LEN (256 << 10)
	#define CONFIG_SYS_BOOTPARAMS_LEN (64*1024)

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization ??
	*/
	#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
	#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20)

	/* FLASH organization */
	#define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE)
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 2048 /* max number of sectors on one chip */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 1000

	#define FLASH_SST6401B 0x200
	#define SST_ID_xF6401B 0x236D236D

	#undef CONFIG_SYS_FLASH_CFI
	#ifdef CONFIG_SYS_FLASH_CFI
	/*
	* Unable to use CFI driver, due to incompatible sector erase command by SST.
	* Amd/Atmel use 0x30 for sector erase, SST use 0x50.
	* 0x30 is block erase in SST
	*/
	# define CONFIG_FLASH_CFI_DRIVER 1
	# define CONFIG_SYS_FLASH_SIZE 0x800000
	# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
	# define CONFIG_FLASH_CFI_LEGACY
	#else
	# define CONFIG_SYS_SST_SECT 2048
	# define CONFIG_SYS_SST_SECTSZ 0x1000
	# define CONFIG_SYS_FLASH_WRITE_TOUT 500
	#endif

	/* Cache Configuration */
	#define CONFIG_SYS_CACHELINE_SIZE 16

	#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
	CONFIG_SYS_INIT_RAM_SIZE - 8)
	#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
	CONFIG_SYS_INIT_RAM_SIZE - 4)
	#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM)
	#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE \| \
	CF_ADDRMASK(8) \| \
	CF_ACR_EN \| CF_ACR_SM_ALL)
	#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE \| \
	CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) \| \
	CF_ACR_EN \| CF_ACR_SM_ALL)
	#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB \| CF_CACR_CEIB \| \
	CF_CACR_DBWE)

	/* Port configuration */
	#define CONFIG_SYS_FECI2C 0xF0

	#define CONFIG_SYS_CS0_BASE 0xFF800000
	#define CONFIG_SYS_CS0_MASK 0x007F0021
	#define CONFIG_SYS_CS0_CTRL 0x00001D80

	#define CONFIG_SYS_CS1_BASE 0xE0000000
	#define CONFIG_SYS_CS1_MASK 0x00000001
	#define CONFIG_SYS_CS1_CTRL 0x00003DD8

	/*-----------------------------------------------------------------------
	* Port configuration
	*/
	#define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */
	#define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */
	#define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */
	#define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */
	#define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */
	#define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */
	#define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */

	#endif /* _M5253DEMO_H */