blob: 2c0a263da293c6e6b36cde1a1304336d0910628f [file] [log] [blame]
/*
* U-boot - Configuration file for IBF-DSP561 board
*/
#ifndef __CONFIG_IBF_DSP561__H__
#define __CONFIG_IBF_DSP561__H__
#include <asm/config-pre.h>
/*
* Processor Settings
*/
#define CONFIG_BFIN_CPU bf561-0.5
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 25000000
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF 0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
/* 1 = bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 24
/* CCLK_DIV controls the core clock divider */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* SCLK_DIV controls the system clock divider */
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 5
/*
* Memory Settings
*/
#define CONFIG_MEM_ADD_WDTH 9
#define CONFIG_MEM_SIZE 64
#define CONFIG_EBIU_SDRRC_VAL 0x377
#define CONFIG_EBIU_SDGCTL_VAL 0x91998d
#define CONFIG_EBIU_SDBCTL_VAL 0x15
#define CONFIG_EBIU_AMGCTL_VAL 0x3F
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
/*
* Network Settings
*/
#define ADI_CMDS_NETWORK 1
#define CONFIG_NET_MULTI
#define CONFIG_DRIVER_AX88180 1
#define AX88180_BASE 0x2c000000
#define CONFIG_HOSTNAME ibf-dsp561
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
/*
* Flash Settings
*/
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_SYS_FLASH_CFI_AMD_RESET
#define CONFIG_SYS_FLASH_BASE 0x20000000
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 135 /* max number of sectors on one chip */
/* The BF561-EZKIT uses a top boot flash */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR 0x20004000
#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
#define ENV_IS_EMBEDDED
#else
#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
#endif
#ifdef ENV_IS_EMBEDDED
/* WARNING - the following is hand-optimized to fit within
* the sector before the environment sector. If it throws
* an error during compilation remove an object here to get
* it linked after the configuration sector.
*/
# define LDS_BOARD_TEXT \
arch/blackfin/cpu/traps.o (.text .text.*); \
arch/blackfin/cpu/interrupt.o (.text .text.*); \
arch/blackfin/cpu/serial.o (.text .text.*); \
common/dlmalloc.o (.text .text.*); \
lib/crc32.o (.text .text.*); \
lib/zlib.o (.text .text.*); \
board/ibf-dsp561/ibf-dsp561.o (.text .text.*); \
. = DEFINED(env_offset) ? env_offset : .; \
common/env_embedded.o (.text .text.*);
#endif
/*
* I2C Settings
*/
#define CONFIG_SOFT_I2C 1
#define PF_SCL 0x1/*PF0*/
#define PF_SDA 0x2/*PF1*/
#ifdef CONFIG_SOFT_I2C
#define I2C_INIT do { *pFIO0_DIR |= PF_SCL; SSYNC(); } while (0)
#define I2C_ACTIVE do { *pFIO0_DIR |= PF_SDA; *pFIO0_INEN &= ~PF_SDA; SSYNC(); } while (0)
#define I2C_TRISTATE do { *pFIO0_DIR &= ~PF_SDA; *pFIO0_INEN |= PF_SDA; SSYNC(); } while (0)
#define I2C_READ ((*pFIO0_FLAG_D & PF_SDA) != 0)
#define I2C_SDA(bit) \
do { \
if (bit) \
*pFIO0_FLAG_S = PF_SDA; \
else \
*pFIO0_FLAG_C = PF_SDA; \
SSYNC(); \
} while (0)
#define I2C_SCL(bit) \
do { \
if (bit) \
*pFIO0_FLAG_S = PF_SCL; \
else \
*pFIO0_FLAG_C = PF_SCL; \
SSYNC(); \
} while (0)
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#endif
/*
* Misc Settings
*/
#define CONFIG_UART_CONSOLE 0
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
#endif