include/configs/meson64_android.h - platform/external/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Configuration for Android Amlogic Meson 64bits SoCs
  *
  * Copyright (C) 2019 Baylibre, SAS
  * Author: Jerome Brunet <jbrunet@baylibre.com>
  */

 #ifndef __MESON64_ANDROID_CONFIG_H
 #define __MESON64_ANDROID_CONFIG_H

 #include <linux/sizes.h>

 #define CONFIG_SYS_MALLOC_LEN	       SZ_128M

 #ifndef BOOT_PARTITION
 #define BOOT_PARTITION "boot"
 #endif

 #ifndef LOGO_PARTITION
 #define LOGO_PARTITION "logo"
 #endif

 #ifndef CONTROL_PARTITION
 #define CONTROL_PARTITION "misc"
 #endif

 #if defined(CONFIG_CMD_AVB)
 #define AVB_VERIFY_CHECK \
 	"if test \"${force_avb}\" -eq 1; then " \
 		"if run avb_verify; then " \
 			"echo AVB verification OK.;" \
 			"setenv bootargs \"$bootargs $avb_bootargs\";" \
 		"else " \
 			"echo AVB verification failed.;" \
 		"exit; fi;" \
 	"else " \
 		"setenv bootargs \"$bootargs androidboot.verifiedbootstate=orange\";" \
 		"echo Running without AVB...; "\
 	"fi;"

 #define AVB_VERIFY_CMD "avb_verify=avb init ${mmcdev}; avb verify $slot_suffix;\0"
 #else
 #define AVB_VERIFY_CHECK ""
 #define AVB_VERIFY_CMD ""
 #endif

 #if defined(CONFIG_CMD_AB_SELECT)
 #define ANDROIDBOOT_GET_CURRENT_SLOT_CMD "get_current_slot=" \
 	"if part number mmc ${mmcdev} " CONTROL_PARTITION " control_part_number; " \
 	"then " \
 		"echo " CONTROL_PARTITION \
 			" partition number:${control_part_number};" \
 		"ab_select current_slot mmc ${mmcdev}:${control_part_number};" \
 	"else " \
 		"echo " CONTROL_PARTITION " partition not found;" \
 	"fi;\0"

 #define AB_SELECT_SLOT \
 	"run get_current_slot; " \
 	"if test -e \"${current_slot}\"; " \
 	"then " \
 		"setenv slot_suffix _${current_slot}; " \
 	"else " \
 		"echo current_slot not found;" \
 		"exit;" \
 	"fi;"

 #define AB_SELECT_ARGS \
 	"setenv bootargs_ab androidboot.slot_suffix=${slot_suffix}; " \
 	"echo A/B cmdline addition: ${bootargs_ab};" \
 	"setenv bootargs ${bootargs} ${bootargs_ab};"

 #define AB_BOOTARGS " androidboot.force_normal_boot=1"
 #define RECOVERY_PARTITION "boot"
 #else
 #define AB_SELECT_SLOT ""
 #define AB_SELECT_ARGS " "
 #define ANDROIDBOOT_GET_CURRENT_SLOT_CMD ""
 #define AB_BOOTARGS " "
 #define RECOVERY_PARTITION "recovery"
 #endif

 #if defined(CONFIG_CMD_ABOOTIMG)
 /*
  * Prepares complete device tree blob for current board (for Android boot).
  *
  * Boot image or recovery image should be loaded into $loadaddr prior to running
  * these commands. The logic of these commnads is next:
  *
  *   1. Read correct DTB for current SoC/board from boot image in $loadaddr
  *      to $fdtaddr
  *   2. Merge all needed DTBO for current board from 'dtbo' partition into read
  *      DTB
  *   3. User should provide $fdtaddr as 3rd argument to 'bootm'
  */
 #define PREPARE_FDT \
 	"echo Preparing FDT...; " \
 	"if test $board_name = sei510; then " \
 		"echo \"  Reading DTB for sei510...\"; " \
 		"setenv dtb_index 0;" \
 	"elif test $board_name = sei610; then " \
 		"echo \"  Reading DTB for sei610...\"; " \
 		"setenv dtb_index 1;" \
 	"else " \
 		"echo Error: Android boot is not supported for $board_name; " \
 		"exit; " \
 	"fi; " \
 	"abootimg get dtb --index=$dtb_index dtb_start dtb_size; " \
 	"cp.b $dtb_start $fdt_addr_r $dtb_size; " \
 	"fdt addr $fdt_addr_r  0x80000; " \
 	"if test $board_name = sei510; then " \
 		"echo \"  Reading DTBO for sei510...\"; " \
 		"setenv dtbo_index 0;" \
 	"elif test $board_name = sei610; then " \
 		"echo \"  Reading DTBO for sei610...\"; " \
 		"setenv dtbo_index 1;" \
 	"else " \
 		"echo Error: Android boot is not supported for $board_name; " \
 		"exit; " \
 	"fi; " \
 	"part start mmc ${mmcdev} dtbo${slot_suffix} p_dtbo_start; " \
 	"part size mmc ${mmcdev} dtbo${slot_suffix} p_dtbo_size; " \
 	"mmc read ${dtboaddr} ${p_dtbo_start} ${p_dtbo_size}; " \
 	"echo \"  Applying DTBOs...\"; " \
 	"adtimg addr $dtboaddr; " \
 	"adtimg get dt --index=$dtbo_index dtbo0_addr; " \
 	"fdt apply $dtbo0_addr;" \
 	"setenv bootargs \"$bootargs androidboot.dtbo_idx=$dtbo_index \";"\

 #define BOOT_CMD "bootm ${loadaddr} ${loadaddr} ${fdt_addr_r};"

 #else
 #define PREPARE_FDT " "
 #define BOOT_CMD "bootm ${loadaddr};"
 #endif

 #define BOOTENV_DEV_FASTBOOT(devtypeu, devtypel, instance) \
 	"bootcmd_fastboot=" \
 		"setenv run_fastboot 0;" \
 		"if test \"${boot_source}\" = \"usb\"; then " \
 			"echo Fastboot forced by usb rom boot;" \
 			"setenv run_fastboot 1;" \
 		"fi;" \
 		"if gpt verify mmc ${mmcdev} ${partitions}; then; " \
 		"else " \
 			"echo Broken MMC partition scheme;" \
 			"setenv run_fastboot 1;" \
 		"fi;" \
 		"if bcb load " __stringify(CONFIG_FASTBOOT_FLASH_MMC_DEV) " " \
 		CONTROL_PARTITION "; then " \
 			"if bcb test command = bootonce-bootloader; then " \
 				"echo BCB: Bootloader boot...; " \
 				"bcb clear command; bcb store; " \
 				"setenv run_fastboot 1;" \
 			"fi; " \
 			"if bcb test command = boot-fastboot; then " \
 				"echo BCB: fastboot userspace boot...; " \
 				"setenv force_recovery 1;" \
 			"fi; " \
 		"else " \
 			"echo Warning: BCB is corrupted or does not exist; " \
 		"fi;" \
 		"if test \"${run_fastboot}\" -eq 1; then " \
 			"echo Running Fastboot...;" \
 			"fastboot " __stringify(CONFIG_FASTBOOT_USB_DEV) "; " \
 		"fi\0"

 #define BOOTENV_DEV_NAME_FASTBOOT(devtypeu, devtypel, instance)	\
 		"fastboot "

 #define BOOTENV_DEV_RECOVERY(devtypeu, devtypel, instance) \
 	"bootcmd_recovery=" \
 		"pinmux dev pinctrl@14;" \
 		"pinmux dev pinctrl@40;" \
 		"setenv run_recovery 0;" \
 		"if run check_button; then " \
 			"echo Recovery button is pressed;" \
 			"setenv run_recovery 1;" \
 		"fi; " \
 		"if bcb load " __stringify(CONFIG_FASTBOOT_FLASH_MMC_DEV) " " \
 		CONTROL_PARTITION "; then " \
 			"if bcb test command = boot-recovery; then " \
 				"echo BCB: Recovery boot...; " \
 				"setenv run_recovery 1;" \
 			"fi;" \
 		"else " \
 			"echo Warning: BCB is corrupted or does not exist; " \
 		"fi;" \
 		"if test \"${skip_recovery}\" -eq 1; then " \
 			"echo Recovery skipped by environment;" \
 			"setenv run_recovery 0;" \
 		"fi;" \
 		"if test \"${force_recovery}\" -eq 1; then " \
 			"echo Recovery forced by environment;" \
 			"setenv run_recovery 1;" \
 		"fi;" \
 		"if test \"${run_recovery}\" -eq 1; then " \
 			"echo Running Recovery...;" \
 			"mmc dev ${mmcdev};" \
 			"setenv bootargs \"${bootargs} androidboot.serialno=${serial#}\";" \
 			AB_SELECT_SLOT \
 			AB_SELECT_ARGS \
 			AVB_VERIFY_CHECK \
 			"part start mmc ${mmcdev} " RECOVERY_PARTITION "${slot_suffix} boot_start;" \
 			"part size mmc ${mmcdev} " RECOVERY_PARTITION "${slot_suffix} boot_size;" \
 			"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
 				PREPARE_FDT \
 				"echo Running Android Recovery...;" \
 				BOOT_CMD \
 			"fi;" \
 			"echo Failed to boot Android...;" \
 			"reset;" \
 		"fi\0"

 #define BOOTENV_DEV_NAME_RECOVERY(devtypeu, devtypel, instance)	\
 		"recovery "

 #define BOOTENV_DEV_SYSTEM(devtypeu, devtypel, instance) \
 	"bootcmd_system=" \
 		"echo Loading Android " BOOT_PARTITION " partition...;" \
 		"mmc dev ${mmcdev};" \
 		"setenv bootargs ${bootargs} androidboot.serialno=${serial#};" \
 		AB_SELECT_SLOT \
 		AB_SELECT_ARGS \
 		AVB_VERIFY_CHECK \
 		"part start mmc ${mmcdev} " BOOT_PARTITION "${slot_suffix} boot_start;" \
 		"part size mmc ${mmcdev} " BOOT_PARTITION "${slot_suffix} boot_size;" \
 		"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
 			PREPARE_FDT \
 			"setenv bootargs \"${bootargs} " AB_BOOTARGS "\"  ; " \
 			"echo Running Android...;" \
 			BOOT_CMD \
 		"fi;" \
 		"echo Failed to boot Android...;" \
 		"reset\0"

 #define BOOTENV_DEV_NAME_SYSTEM(devtypeu, devtypel, instance)	\
 		"system "

 #define BOOT_TARGET_DEVICES(func) \
 	func(FASTBOOT, fastboot, na) \
 	func(RECOVERY, recovery, na) \
 	func(SYSTEM, system, na) \

 #define PREBOOT_LOAD_LOGO \
 	"if test \"${boot_source}\" != \"usb\" && " \
 		"gpt verify mmc ${mmcdev} ${partitions}; then; " \
 		"mmc dev ${mmcdev};" \
 		"part start mmc ${mmcdev} " LOGO_PARTITION " boot_start;" \
 		"part size mmc ${mmcdev} " LOGO_PARTITION " boot_size;" \
 		"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
 			"bmp display ${loadaddr} m m;" \
 		"fi;" \
 	"fi;"

 #define CONFIG_EXTRA_ENV_SETTINGS                                     \
 	"partitions=" PARTS_DEFAULT "\0"                              \
 	"mmcdev=2\0"                                                  \
 	ANDROIDBOOT_GET_CURRENT_SLOT_CMD                              \
 	AVB_VERIFY_CMD                                                \
 	"force_avb=0\0"                                               \
 	"gpio_recovery=88\0"                                          \
 	"check_button=gpio input ${gpio_recovery};test $? -eq 0;\0"   \
 	"load_logo=" PREBOOT_LOAD_LOGO "\0"			      \
 	"stdin=" STDIN_CFG "\0"                                       \
 	"stdout=" STDOUT_CFG "\0"                                     \
 	"stderr=" STDOUT_CFG "\0"                                     \
 	"dtboaddr=0x08200000\0"                                       \
 	"loadaddr=0x01080000\0"                                       \
 	"fdt_addr_r=0x01000000\0"                                     \
 	"scriptaddr=0x08000000\0"                                     \
 	"kernel_addr_r=0x01080000\0"                                  \
 	"pxefile_addr_r=0x01080000\0"                                 \
 	"ramdisk_addr_r=0x13000000\0"                                 \
 	"fdtfile=amlogic/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0"        \
 	BOOTENV

 #include <configs/meson64.h>

 #endif /* __MESON64_ANDROID_CONFIG_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Configuration for Android Amlogic Meson 64bits SoCs
	*
	* Copyright (C) 2019 Baylibre, SAS
	* Author: Jerome Brunet <jbrunet@baylibre.com>
	*/

	#ifndef __MESON64_ANDROID_CONFIG_H
	#define __MESON64_ANDROID_CONFIG_H

	#include <linux/sizes.h>

	#define CONFIG_SYS_MALLOC_LEN SZ_128M

	#ifndef BOOT_PARTITION
	#define BOOT_PARTITION "boot"
	#endif

	#ifndef LOGO_PARTITION
	#define LOGO_PARTITION "logo"
	#endif

	#ifndef CONTROL_PARTITION
	#define CONTROL_PARTITION "misc"
	#endif

	#if defined(CONFIG_CMD_AVB)
	#define AVB_VERIFY_CHECK \
	"if test \"${force_avb}\" -eq 1; then " \
	"if run avb_verify; then " \
	"echo AVB verification OK.;" \
	"setenv bootargs \"$bootargs $avb_bootargs\";" \
	"else " \
	"echo AVB verification failed.;" \
	"exit; fi;" \
	"else " \
	"setenv bootargs \"$bootargs androidboot.verifiedbootstate=orange\";" \
	"echo Running without AVB...; "\
	"fi;"

	#define AVB_VERIFY_CMD "avb_verify=avb init ${mmcdev}; avb verify $slot_suffix;\0"
	#else
	#define AVB_VERIFY_CHECK ""
	#define AVB_VERIFY_CMD ""
	#endif

	#if defined(CONFIG_CMD_AB_SELECT)
	#define ANDROIDBOOT_GET_CURRENT_SLOT_CMD "get_current_slot=" \
	"if part number mmc ${mmcdev} " CONTROL_PARTITION " control_part_number; " \
	"then " \
	"echo " CONTROL_PARTITION \
	" partition number:${control_part_number};" \
	"ab_select current_slot mmc ${mmcdev}:${control_part_number};" \
	"else " \
	"echo " CONTROL_PARTITION " partition not found;" \
	"fi;\0"

	#define AB_SELECT_SLOT \
	"run get_current_slot; " \
	"if test -e \"${current_slot}\"; " \
	"then " \
	"setenv slot_suffix _${current_slot}; " \
	"else " \
	"echo current_slot not found;" \
	"exit;" \
	"fi;"

	#define AB_SELECT_ARGS \
	"setenv bootargs_ab androidboot.slot_suffix=${slot_suffix}; " \
	"echo A/B cmdline addition: ${bootargs_ab};" \
	"setenv bootargs ${bootargs} ${bootargs_ab};"

	#define AB_BOOTARGS " androidboot.force_normal_boot=1"
	#define RECOVERY_PARTITION "boot"
	#else
	#define AB_SELECT_SLOT ""
	#define AB_SELECT_ARGS " "
	#define ANDROIDBOOT_GET_CURRENT_SLOT_CMD ""
	#define AB_BOOTARGS " "
	#define RECOVERY_PARTITION "recovery"
	#endif

	#if defined(CONFIG_CMD_ABOOTIMG)
	/*
	* Prepares complete device tree blob for current board (for Android boot).
	*
	* Boot image or recovery image should be loaded into $loadaddr prior to running
	* these commands. The logic of these commnads is next:
	*
	* 1. Read correct DTB for current SoC/board from boot image in $loadaddr
	* to $fdtaddr
	* 2. Merge all needed DTBO for current board from 'dtbo' partition into read
	* DTB
	* 3. User should provide $fdtaddr as 3rd argument to 'bootm'
	*/
	#define PREPARE_FDT \
	"echo Preparing FDT...; " \
	"if test $board_name = sei510; then " \
	"echo \" Reading DTB for sei510...\"; " \
	"setenv dtb_index 0;" \
	"elif test $board_name = sei610; then " \
	"echo \" Reading DTB for sei610...\"; " \
	"setenv dtb_index 1;" \
	"else " \
	"echo Error: Android boot is not supported for $board_name; " \
	"exit; " \
	"fi; " \
	"abootimg get dtb --index=$dtb_index dtb_start dtb_size; " \
	"cp.b $dtb_start $fdt_addr_r $dtb_size; " \
	"fdt addr $fdt_addr_r 0x80000; " \
	"if test $board_name = sei510; then " \
	"echo \" Reading DTBO for sei510...\"; " \
	"setenv dtbo_index 0;" \
	"elif test $board_name = sei610; then " \
	"echo \" Reading DTBO for sei610...\"; " \
	"setenv dtbo_index 1;" \
	"else " \
	"echo Error: Android boot is not supported for $board_name; " \
	"exit; " \
	"fi; " \
	"part start mmc ${mmcdev} dtbo${slot_suffix} p_dtbo_start; " \
	"part size mmc ${mmcdev} dtbo${slot_suffix} p_dtbo_size; " \
	"mmc read ${dtboaddr} ${p_dtbo_start} ${p_dtbo_size}; " \
	"echo \" Applying DTBOs...\"; " \
	"adtimg addr $dtboaddr; " \
	"adtimg get dt --index=$dtbo_index dtbo0_addr; " \
	"fdt apply $dtbo0_addr;" \
	"setenv bootargs \"$bootargs androidboot.dtbo_idx=$dtbo_index \";"\

	#define BOOT_CMD "bootm ${loadaddr} ${loadaddr} ${fdt_addr_r};"

	#else
	#define PREPARE_FDT " "
	#define BOOT_CMD "bootm ${loadaddr};"
	#endif

	#define BOOTENV_DEV_FASTBOOT(devtypeu, devtypel, instance) \
	"bootcmd_fastboot=" \
	"setenv run_fastboot 0;" \
	"if test \"${boot_source}\" = \"usb\"; then " \
	"echo Fastboot forced by usb rom boot;" \
	"setenv run_fastboot 1;" \
	"fi;" \
	"if gpt verify mmc ${mmcdev} ${partitions}; then; " \
	"else " \
	"echo Broken MMC partition scheme;" \
	"setenv run_fastboot 1;" \
	"fi;" \
	"if bcb load " __stringify(CONFIG_FASTBOOT_FLASH_MMC_DEV) " " \
	CONTROL_PARTITION "; then " \
	"if bcb test command = bootonce-bootloader; then " \
	"echo BCB: Bootloader boot...; " \
	"bcb clear command; bcb store; " \
	"setenv run_fastboot 1;" \
	"fi; " \
	"if bcb test command = boot-fastboot; then " \
	"echo BCB: fastboot userspace boot...; " \
	"setenv force_recovery 1;" \
	"fi; " \
	"else " \
	"echo Warning: BCB is corrupted or does not exist; " \
	"fi;" \
	"if test \"${run_fastboot}\" -eq 1; then " \
	"echo Running Fastboot...;" \
	"fastboot " __stringify(CONFIG_FASTBOOT_USB_DEV) "; " \
	"fi\0"

	#define BOOTENV_DEV_NAME_FASTBOOT(devtypeu, devtypel, instance) \
	"fastboot "

	#define BOOTENV_DEV_RECOVERY(devtypeu, devtypel, instance) \
	"bootcmd_recovery=" \
	"pinmux dev pinctrl@14;" \
	"pinmux dev pinctrl@40;" \
	"setenv run_recovery 0;" \
	"if run check_button; then " \
	"echo Recovery button is pressed;" \
	"setenv run_recovery 1;" \
	"fi; " \
	"if bcb load " __stringify(CONFIG_FASTBOOT_FLASH_MMC_DEV) " " \
	CONTROL_PARTITION "; then " \
	"if bcb test command = boot-recovery; then " \
	"echo BCB: Recovery boot...; " \
	"setenv run_recovery 1;" \
	"fi;" \
	"else " \
	"echo Warning: BCB is corrupted or does not exist; " \
	"fi;" \
	"if test \"${skip_recovery}\" -eq 1; then " \
	"echo Recovery skipped by environment;" \
	"setenv run_recovery 0;" \
	"fi;" \
	"if test \"${force_recovery}\" -eq 1; then " \
	"echo Recovery forced by environment;" \
	"setenv run_recovery 1;" \
	"fi;" \
	"if test \"${run_recovery}\" -eq 1; then " \
	"echo Running Recovery...;" \
	"mmc dev ${mmcdev};" \
	"setenv bootargs \"${bootargs} androidboot.serialno=${serial#}\";" \
	AB_SELECT_SLOT \
	AB_SELECT_ARGS \
	AVB_VERIFY_CHECK \
	"part start mmc ${mmcdev} " RECOVERY_PARTITION "${slot_suffix} boot_start;" \
	"part size mmc ${mmcdev} " RECOVERY_PARTITION "${slot_suffix} boot_size;" \
	"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
	PREPARE_FDT \
	"echo Running Android Recovery...;" \
	BOOT_CMD \
	"fi;" \
	"echo Failed to boot Android...;" \
	"reset;" \
	"fi\0"

	#define BOOTENV_DEV_NAME_RECOVERY(devtypeu, devtypel, instance) \
	"recovery "

	#define BOOTENV_DEV_SYSTEM(devtypeu, devtypel, instance) \
	"bootcmd_system=" \
	"echo Loading Android " BOOT_PARTITION " partition...;" \
	"mmc dev ${mmcdev};" \
	"setenv bootargs ${bootargs} androidboot.serialno=${serial#};" \
	AB_SELECT_SLOT \
	AB_SELECT_ARGS \
	AVB_VERIFY_CHECK \
	"part start mmc ${mmcdev} " BOOT_PARTITION "${slot_suffix} boot_start;" \
	"part size mmc ${mmcdev} " BOOT_PARTITION "${slot_suffix} boot_size;" \
	"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
	PREPARE_FDT \
	"setenv bootargs \"${bootargs} " AB_BOOTARGS "\" ; " \
	"echo Running Android...;" \
	BOOT_CMD \
	"fi;" \
	"echo Failed to boot Android...;" \
	"reset\0"

	#define BOOTENV_DEV_NAME_SYSTEM(devtypeu, devtypel, instance) \
	"system "

	#define BOOT_TARGET_DEVICES(func) \
	func(FASTBOOT, fastboot, na) \
	func(RECOVERY, recovery, na) \
	func(SYSTEM, system, na) \

	#define PREBOOT_LOAD_LOGO \
	"if test \"${boot_source}\" != \"usb\" && " \
	"gpt verify mmc ${mmcdev} ${partitions}; then; " \
	"mmc dev ${mmcdev};" \
	"part start mmc ${mmcdev} " LOGO_PARTITION " boot_start;" \
	"part size mmc ${mmcdev} " LOGO_PARTITION " boot_size;" \
	"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
	"bmp display ${loadaddr} m m;" \
	"fi;" \
	"fi;"

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"partitions=" PARTS_DEFAULT "\0" \
	"mmcdev=2\0" \
	ANDROIDBOOT_GET_CURRENT_SLOT_CMD \
	AVB_VERIFY_CMD \
	"force_avb=0\0" \
	"gpio_recovery=88\0" \
	"check_button=gpio input ${gpio_recovery};test $? -eq 0;\0" \
	"load_logo=" PREBOOT_LOAD_LOGO "\0" \
	"stdin=" STDIN_CFG "\0" \
	"stdout=" STDOUT_CFG "\0" \
	"stderr=" STDOUT_CFG "\0" \
	"dtboaddr=0x08200000\0" \
	"loadaddr=0x01080000\0" \
	"fdt_addr_r=0x01000000\0" \
	"scriptaddr=0x08000000\0" \
	"kernel_addr_r=0x01080000\0" \
	"pxefile_addr_r=0x01080000\0" \
	"ramdisk_addr_r=0x13000000\0" \
	"fdtfile=amlogic/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
	BOOTENV

	#include <configs/meson64.h>

	#endif /* __MESON64_ANDROID_CONFIG_H */