include/configs/ep82xxm.h - platform/external/u-boot - Gitiles

 /*
  * Copyright (C) 2006 Embedded Planet, LLC.
  *
  * U-Boot configuration for Embedded Planet EP82xxM boards.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #define CONFIG_MPC8260
 #define CPU_ID_STR		"MPC8270"

 #define CONFIG_EP82XXM	/* Embedded Planet EP82xxM H 1.0 board */
 			/* 256MB SDRAM / 64MB FLASH */

 #define	CONFIG_SYS_TEXT_BASE	0xFFF00000

 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f */

 /* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
 #define CONFIG_ENV_OVERWRITE

 /*
  * Select serial console configuration
  *
  * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
  * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
  * for SCC).
  */
 #define	CONFIG_CONS_ON_SMC		/* Console is on SMC         */
 #undef  CONFIG_CONS_ON_SCC		/* It's not on SCC           */
 #undef	CONFIG_CONS_NONE		/* It's not on external UART */
 #define CONFIG_CONS_INDEX	1	/* SMC1 is used for console  */

 #define CONFIG_SYS_BCSR		0xFA000000

 /*
  * Select ethernet configuration
  *
  * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
  * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
  * SCC, 1-3 for FCC)
  *
  * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
  * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
  * must be unset.
  */
 #undef	CONFIG_ETHER_ON_SCC		/* Ethernet is not on SCC */
 #define CONFIG_ETHER_ON_FCC		/* Ethernet is on FCC     */
 #undef	CONFIG_ETHER_NONE		/* No external Ethernet   */


 #define CONFIG_ETHER_ON_FCC2
 #define CONFIG_ETHER_ON_FCC3

 #define CONFIG_SYS_CMXFCR_MASK3	(CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
 #define CONFIG_SYS_CMXFCR_VALUE3	(CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK16)
 #define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
 #define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)

 #define CONFIG_SYS_CPMFCR_RAMTYPE	0
 #define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)

 #define CONFIG_MII			/* MII PHY management        */
 #define CONFIG_BITBANGMII		/* Bit-banged MDIO interface */

 /*
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		0	/* Not used - implemented in BCSR */

 #define MDIO_ACTIVE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
 #define MDIO_TRISTATE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
 #define MDIO_READ		(*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)

 #define MDIO(bit)		if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x01; \
 				else	*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFE

 #define MDC(bit)		if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x02; \
 				else	*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFD

 #define MIIDELAY		udelay(1)


 #ifndef CONFIG_8260_CLKIN
 #define CONFIG_8260_CLKIN	66000000 /* in Hz */
 #endif

 #define CONFIG_BAUDRATE		115200

 #define CONFIG_SYS_VXWORKS_MAC_PTR 0x4300 /* Pass Ethernet MAC to VxWorks */


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>


 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ECHO
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IMMAP
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DTT
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_DIAG


 #define CONFIG_ETHADDR		00:10:EC:00:88:65
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR		00:10:EC:80:88:65
 #define CONFIG_IPADDR		10.0.0.245
 #define CONFIG_HOSTNAME		EP82xxM
 #define CONFIG_SERVERIP		10.0.0.26
 #define CONFIG_GATEWAYIP	10.0.0.1
 #define CONFIG_NETMASK		255.255.255.0
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
 #define CONFIG_ENV_IN_OWN_SECT	1
 #define CONFIG_AUTO_COMPLETE	1
 #define	CONFIG_EXTRA_ENV_SETTINGS	"ethprime=FCC3"

 #if defined(CONFIG_CMD_KGDB)
 #undef	CONFIG_KGDB_ON_SMC		/* define if kgdb on SMC */
 #define CONFIG_KGDB_ON_SCC		/* define if kgdb on SCC */
 #undef	CONFIG_KGDB_NONE		/* define if kgdb on something else */
 #define CONFIG_KGDB_INDEX	1	/* which serial channel for kgdb */
 #define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port at */
 #endif

 #define CONFIG_BZIP2	/* include support for bzip2 compressed images */
 #undef	CONFIG_WATCHDOG			/* disable platform specific watchdog */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
 #define CONFIG_SYS_PROMPT		"ep82xxm=> "	/* Monitor Command Prompt   */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size  */
 #define CONFIG_SYS_MAXARGS		16		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size  */

 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/

 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */

 #define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks */

 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }

 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
 /*
  * Define here the location of the environment variables (FLASH or EEPROM).
  * Note: DENX encourages to use redundant environment in FLASH.
  */
 #if 1
 #define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
 #else
 #define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars	*/
 #endif

 /*-----------------------------------------------------------------------
  * FLASH related
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_FLASH_BASE		0xFC000000
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks	*/
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* max num of sects on one chip */
 #define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector in flinfo */

 #ifdef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_SECT_SIZE	0x20000
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 #endif /* CONFIG_ENV_IS_IN_FLASH */

 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
 /* EEPROM Configuration */
 #define CONFIG_SYS_EEPROM_SIZE	0x1000
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x54
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10

 #ifdef CONFIG_ENV_IS_IN_EEPROM
 #define CONFIG_ENV_SIZE		0x200	    /* Size of Environment vars */
 #define CONFIG_ENV_OFFSET		0x0
 #endif /* CONFIG_ENV_IS_IN_EEPROM */

 /* RTC Configuration */
 #define CONFIG_RTC_M41T11	1	/* uses a M41T81 */
 #define CONFIG_SYS_I2C_RTC_ADDR	0x68
 #define CONFIG_M41T11_BASE_YEAR	1900

 /* I2C SYSMON (LM75) */
 #define CONFIG_DTT_LM75		1
 #define CONFIG_DTT_SENSORS	{0}
 #define CONFIG_SYS_DTT_MAX_TEMP	70
 #define CONFIG_SYS_DTT_LOW_TEMP	-30
 #define	CONFIG_SYS_DTT_HYSTERESIS	3

 /*-----------------------------------------------------------------------
  * NVRAM Configuration
  *-----------------------------------------------------------------------
  */
 #define CONFIG_SYS_NVRAM_BASE_ADDR	0xFA080000
 #define CONFIG_SYS_NVRAM_SIZE		(128*1024)-16


 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
  */
 /* General PCI */
 #define CONFIG_PCI			/* include pci support	        */
 #define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
 #define CONFIG_PCI_PNP			/* do pci plug-and-play   */
 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup  */
 #define CONFIG_PCI_BOOTDELAY	0

 /* PCI Memory map (if different from default map */
 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL	CONFIG_SYS_SDRAM_BASE		/* Local base */
 #define CONFIG_SYS_PCI_SLV_MEM_BUS		0x00000000	/* PCI base */
 #define CONFIG_SYS_PICMR0_MASK_ATTRIB	(PICMR_MASK_512MB | PICMR_ENABLE | \
 				 PICMR_PREFETCH_EN)

 /*
  * These are the windows that allow the CPU to access PCI address space.
  * All three PCI master windows, which allow the CPU to access PCI
  * prefetch, non prefetch, and IO space (see below), must all fit within
  * these windows.
  */

 /*
  * Master window that allows the CPU to access PCI Memory (prefetch).
  * This window will be setup with the second set of Outbound ATU registers
  * in the bridge.
  */

 #define CONFIG_SYS_PCI_MSTR_MEM_LOCAL	0x80000000          /* Local base */
 #define CONFIG_SYS_PCI_MSTR_MEM_BUS	0x80000000          /* PCI base   */
 #define	CONFIG_SYS_CPU_PCI_MEM_START	PCI_MSTR_MEM_LOCAL
 #define CONFIG_SYS_PCI_MSTR_MEM_SIZE	0x20000000          /* 512MB */
 #define CONFIG_SYS_POCMR0_MASK_ATTRIB	(POCMR_MASK_512MB | POCMR_ENABLE | POCMR_PREFETCH_EN)

 /*
  * Master window that allows the CPU to access PCI Memory (non-prefetch).
  * This window will be setup with the second set of Outbound ATU registers
  * in the bridge.
  */

 #define CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL    0xA0000000          /* Local base */
 #define CONFIG_SYS_PCI_MSTR_MEMIO_BUS      0xA0000000          /* PCI base   */
 #define CONFIG_SYS_CPU_PCI_MEMIO_START     PCI_MSTR_MEMIO_LOCAL
 #define CONFIG_SYS_PCI_MSTR_MEMIO_SIZE     0x20000000          /* 512MB */
 #define CONFIG_SYS_POCMR1_MASK_ATTRIB      (POCMR_MASK_512MB | POCMR_ENABLE)

 /*
  * Master window that allows the CPU to access PCI IO space.
  * This window will be setup with the first set of Outbound ATU registers
  * in the bridge.
  */

 #define CONFIG_SYS_PCI_MSTR_IO_LOCAL       0xF6000000          /* Local base */
 #define CONFIG_SYS_PCI_MSTR_IO_BUS         0x00000000          /* PCI base   */
 #define CONFIG_SYS_CPU_PCI_IO_START        PCI_MSTR_IO_LOCAL
 #define CONFIG_SYS_PCI_MSTR_IO_SIZE        0x02000000          /* 64MB */
 #define CONFIG_SYS_POCMR2_MASK_ATTRIB      (POCMR_MASK_32MB | POCMR_ENABLE | POCMR_PCI_IO)


 /* PCIBR0 - for PCI IO*/
 #define CONFIG_SYS_PCI_MSTR0_LOCAL		CONFIG_SYS_PCI_MSTR_IO_LOCAL		/* Local base */
 #define CONFIG_SYS_PCIMSK0_MASK		~(CONFIG_SYS_PCI_MSTR_IO_SIZE - 1U)	/* Size of window */
 /* PCIBR1 - prefetch and non-prefetch regions joined together */
 #define CONFIG_SYS_PCI_MSTR1_LOCAL		CONFIG_SYS_PCI_MSTR_MEM_LOCAL
 #define CONFIG_SYS_PCIMSK1_MASK		~(CONFIG_SYS_PCI_MSTR_MEM_SIZE + CONFIG_SYS_PCI_MSTR_MEMIO_SIZE - 1U)


 #define	CONFIG_SYS_DIRECT_FLASH_TFTP

 #if defined(CONFIG_CMD_JFFS2)
 #define CONFIG_SYS_JFFS2_FIRST_BANK	0
 #define CONFIG_SYS_JFFS2_NUM_BANKS	CONFIG_SYS_MAX_FLASH_BANKS
 #define CONFIG_SYS_JFFS2_FIRST_SECTOR  0
 #define CONFIG_SYS_JFFS2_LAST_SECTOR   62
 #define CONFIG_SYS_JFFS2_SORT_FRAGMENTS
 #define CONFIG_SYS_JFFS_CUSTOM_PART
 #endif

 #if defined(CONFIG_CMD_I2C)
 #define CONFIG_HARD_I2C		1	/* To enable I2C support	*/
 #define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed			*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F	/* I2C slave address		*/
 #endif

 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
 #endif

 #define CONFIG_SYS_MONITOR_LEN		(512 << 10)	/* Reserve 256KB for Monitor */

 #define CONFIG_SYS_DEFAULT_IMMR	0x00010000
 #define CONFIG_SYS_IMMR		0xF0000000

 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
 #define CONFIG_SYS_INIT_RAM_SIZE	0x2000	/* Size of used area in DPRAM	*/
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET


 /* Hard reset configuration word */
 #define CONFIG_SYS_HRCW_MASTER		0 /*0x1C800641*/  /* Not used - provided by CPLD */
 /* No slaves */
 #define CONFIG_SYS_HRCW_SLAVE1		0
 #define CONFIG_SYS_HRCW_SLAVE2		0
 #define CONFIG_SYS_HRCW_SLAVE3		0
 #define CONFIG_SYS_HRCW_SLAVE4		0
 #define CONFIG_SYS_HRCW_SLAVE5		0
 #define CONFIG_SYS_HRCW_SLAVE6		0
 #define CONFIG_SYS_HRCW_SLAVE7		0

 #define CONFIG_SYS_MALLOC_LEN		(4096 << 10)	/* Reserve 4 MB for malloc()	*/
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

 #define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8260 CPUs */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif

 #define CONFIG_SYS_HID0_INIT		0
 #define CONFIG_SYS_HID0_FINAL		0

 #define CONFIG_SYS_HID2		0

 #define CONFIG_SYS_SIUMCR		0x02610000
 #define CONFIG_SYS_SYPCR		0xFFFF0689
 #define CONFIG_SYS_BCR			0x8080E000
 #define CONFIG_SYS_SCCR		0x00000001

 #define CONFIG_SYS_RMR			0
 #define CONFIG_SYS_TMCNTSC		0x000000C3
 #define CONFIG_SYS_PISCR		0x00000083
 #define CONFIG_SYS_RCCR		0

 #define CONFIG_SYS_MPTPR		0x0A00
 #define CONFIG_SYS_PSDMR		0xC432246E
 #define CONFIG_SYS_PSRT		0x32

 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_SDRAM_BR		(CONFIG_SYS_SDRAM_BASE | 0x00000041)
 #define CONFIG_SYS_SDRAM_OR		0xF0002900

 #define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | 0x00001801)
 #define CONFIG_SYS_OR0_PRELIM		0xFC000882
 #define CONFIG_SYS_BR4_PRELIM		(CONFIG_SYS_BCSR | 0x00001001)
 #define CONFIG_SYS_OR4_PRELIM		0xFFF00050

 #define CONFIG_SYS_RESET_ADDRESS	0xFFF00100

 #endif /* __CONFIG_H */
	/*
	* Copyright (C) 2006 Embedded Planet, LLC.
	*
	* U-Boot configuration for Embedded Planet EP82xxM boards.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#define CONFIG_MPC8260
	#define CPU_ID_STR "MPC8270"

	#define CONFIG_EP82XXM /* Embedded Planet EP82xxM H 1.0 board */
	/* 256MB SDRAM / 64MB FLASH */

	#define CONFIG_SYS_TEXT_BASE 0xFFF00000

	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */

	/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
	#define CONFIG_ENV_OVERWRITE

	/*
	* Select serial console configuration
	*
	* If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
	* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
	* for SCC).
	*/
	#define CONFIG_CONS_ON_SMC /* Console is on SMC */
	#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
	#undef CONFIG_CONS_NONE /* It's not on external UART */
	#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */

	#define CONFIG_SYS_BCSR 0xFA000000

	/*
	* Select ethernet configuration
	*
	* If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
	* then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
	* SCC, 1-3 for FCC)
	*
	* If CONFIG_ETHER_NONE is defined, then either the ethernet routines
	* must be defined elsewhere (as for the console), or CONFIG_CMD_NET
	* must be unset.
	*/
	#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
	#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
	#undef CONFIG_ETHER_NONE /* No external Ethernet */


	#define CONFIG_ETHER_ON_FCC2
	#define CONFIG_ETHER_ON_FCC3

	#define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3 \| CMXFCR_RF3CS_MSK \| CMXFCR_TF3CS_MSK)
	#define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 \| CMXFCR_TF3CS_CLK16)
	#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 \| CMXFCR_RF2CS_MSK \| CMXFCR_TF2CS_MSK)
	#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 \| CMXFCR_TF2CS_CLK14)

	#define CONFIG_SYS_CPMFCR_RAMTYPE 0
	#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE \| FCC_PSMR_LPB)

	#define CONFIG_MII /* MII PHY management */
	#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */

	/*
	* GPIO pins used for bit-banged MII communications
	*/
	#define MDIO_PORT 0 /* Not used - implemented in BCSR */

	#define MDIO_ACTIVE ((vu_char )(CONFIG_SYS_BCSR + 8) &= 0xFB)
	#define MDIO_TRISTATE ((vu_char )(CONFIG_SYS_BCSR + 8) \|= 0x04)
	#define MDIO_READ ((vu_char )(CONFIG_SYS_BCSR + 8) & 1)

	#define MDIO(bit) if(bit) (vu_char )(CONFIG_SYS_BCSR + 8) \|= 0x01; \
	else (vu_char )(CONFIG_SYS_BCSR + 8) &= 0xFE

	#define MDC(bit) if(bit) (vu_char )(CONFIG_SYS_BCSR + 8) \|= 0x02; \
	else (vu_char )(CONFIG_SYS_BCSR + 8) &= 0xFD

	#define MIIDELAY udelay(1)


	#ifndef CONFIG_8260_CLKIN
	#define CONFIG_8260_CLKIN 66000000 /* in Hz */
	#endif

	#define CONFIG_BAUDRATE 115200

	#define CONFIG_SYS_VXWORKS_MAC_PTR 0x4300 /* Pass Ethernet MAC to VxWorks */


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>


	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_ECHO
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_IMMAP
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_DTT
	#define CONFIG_CMD_EEPROM
	#define CONFIG_CMD_PCI
	#define CONFIG_CMD_DIAG


	#define CONFIG_ETHADDR 00:10:EC:00:88:65
	#define CONFIG_HAS_ETH1
	#define CONFIG_ETH1ADDR 00:10:EC:80:88:65
	#define CONFIG_IPADDR 10.0.0.245
	#define CONFIG_HOSTNAME EP82xxM
	#define CONFIG_SERVERIP 10.0.0.26
	#define CONFIG_GATEWAYIP 10.0.0.1
	#define CONFIG_NETMASK 255.255.255.0
	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
	#define CONFIG_ENV_IN_OWN_SECT 1
	#define CONFIG_AUTO_COMPLETE 1
	#define CONFIG_EXTRA_ENV_SETTINGS "ethprime=FCC3"

	#if defined(CONFIG_CMD_KGDB)
	#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
	#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
	#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
	#define CONFIG_KGDB_INDEX 1 /* which serial channel for kgdb */
	#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
	#endif

	#define CONFIG_BZIP2 /* include support for bzip2 compressed images */
	#undef CONFIG_WATCHDOG /* disable platform specific watchdog */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_HUSH_PARSER
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_PROMPT "ep82xxm=> " /* Monitor Command Prompt */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */

	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */

	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }

	/*-----------------------------------------------------------------------
	* Environment
	----------------------------------------------------------------------/
	/*
	* Define here the location of the environment variables (FLASH or EEPROM).
	* Note: DENX encourages to use redundant environment in FLASH.
	*/
	#if 1
	#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
	#else
	#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
	#endif

	/*-----------------------------------------------------------------------
	* FLASH related
	----------------------------------------------------------------------/
	#define CONFIG_SYS_FLASH_BASE 0xFC000000
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
	#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector in flinfo */

	#ifdef CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_SECT_SIZE 0x20000
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
	#endif /* CONFIG_ENV_IS_IN_FLASH */

	/*-----------------------------------------------------------------------
	* I2C
	----------------------------------------------------------------------/
	/* EEPROM Configuration */
	#define CONFIG_SYS_EEPROM_SIZE 0x1000
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10

	#ifdef CONFIG_ENV_IS_IN_EEPROM
	#define CONFIG_ENV_SIZE 0x200 /* Size of Environment vars */
	#define CONFIG_ENV_OFFSET 0x0
	#endif /* CONFIG_ENV_IS_IN_EEPROM */

	/* RTC Configuration */
	#define CONFIG_RTC_M41T11 1 /* uses a M41T81 */
	#define CONFIG_SYS_I2C_RTC_ADDR 0x68
	#define CONFIG_M41T11_BASE_YEAR 1900

	/* I2C SYSMON (LM75) */
	#define CONFIG_DTT_LM75 1
	#define CONFIG_DTT_SENSORS {0}
	#define CONFIG_SYS_DTT_MAX_TEMP 70
	#define CONFIG_SYS_DTT_LOW_TEMP -30
	#define CONFIG_SYS_DTT_HYSTERESIS 3

	/*-----------------------------------------------------------------------
	* NVRAM Configuration
	*-----------------------------------------------------------------------
	*/
	#define CONFIG_SYS_NVRAM_BASE_ADDR 0xFA080000
	#define CONFIG_SYS_NVRAM_SIZE (128*1024)-16


	/*-----------------------------------------------------------------------
	* PCI stuff
	*-----------------------------------------------------------------------
	*/
	/* General PCI */
	#define CONFIG_PCI /* include pci support */
	#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#define CONFIG_PCI_BOOTDELAY 0

	/* PCI Memory map (if different from default map */
	#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE /* Local base */
	#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 /* PCI base */
	#define CONFIG_SYS_PICMR0_MASK_ATTRIB (PICMR_MASK_512MB \| PICMR_ENABLE \| \
	PICMR_PREFETCH_EN)

	/*
	* These are the windows that allow the CPU to access PCI address space.
	* All three PCI master windows, which allow the CPU to access PCI
	* prefetch, non prefetch, and IO space (see below), must all fit within
	* these windows.
	*/

	/*
	* Master window that allows the CPU to access PCI Memory (prefetch).
	* This window will be setup with the second set of Outbound ATU registers
	* in the bridge.
	*/

	#define CONFIG_SYS_PCI_MSTR_MEM_LOCAL 0x80000000 /* Local base */
	#define CONFIG_SYS_PCI_MSTR_MEM_BUS 0x80000000 /* PCI base */
	#define CONFIG_SYS_CPU_PCI_MEM_START PCI_MSTR_MEM_LOCAL
	#define CONFIG_SYS_PCI_MSTR_MEM_SIZE 0x20000000 /* 512MB */
	#define CONFIG_SYS_POCMR0_MASK_ATTRIB (POCMR_MASK_512MB \| POCMR_ENABLE \| POCMR_PREFETCH_EN)

	/*
	* Master window that allows the CPU to access PCI Memory (non-prefetch).
	* This window will be setup with the second set of Outbound ATU registers
	* in the bridge.
	*/

	#define CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL 0xA0000000 /* Local base */
	#define CONFIG_SYS_PCI_MSTR_MEMIO_BUS 0xA0000000 /* PCI base */
	#define CONFIG_SYS_CPU_PCI_MEMIO_START PCI_MSTR_MEMIO_LOCAL
	#define CONFIG_SYS_PCI_MSTR_MEMIO_SIZE 0x20000000 /* 512MB */
	#define CONFIG_SYS_POCMR1_MASK_ATTRIB (POCMR_MASK_512MB \| POCMR_ENABLE)

	/*
	* Master window that allows the CPU to access PCI IO space.
	* This window will be setup with the first set of Outbound ATU registers
	* in the bridge.
	*/

	#define CONFIG_SYS_PCI_MSTR_IO_LOCAL 0xF6000000 /* Local base */
	#define CONFIG_SYS_PCI_MSTR_IO_BUS 0x00000000 /* PCI base */
	#define CONFIG_SYS_CPU_PCI_IO_START PCI_MSTR_IO_LOCAL
	#define CONFIG_SYS_PCI_MSTR_IO_SIZE 0x02000000 /* 64MB */
	#define CONFIG_SYS_POCMR2_MASK_ATTRIB (POCMR_MASK_32MB \| POCMR_ENABLE \| POCMR_PCI_IO)


	/* PCIBR0 - for PCI IO*/
	#define CONFIG_SYS_PCI_MSTR0_LOCAL CONFIG_SYS_PCI_MSTR_IO_LOCAL /* Local base */
	#define CONFIG_SYS_PCIMSK0_MASK ~(CONFIG_SYS_PCI_MSTR_IO_SIZE - 1U) /* Size of window */
	/* PCIBR1 - prefetch and non-prefetch regions joined together */
	#define CONFIG_SYS_PCI_MSTR1_LOCAL CONFIG_SYS_PCI_MSTR_MEM_LOCAL
	#define CONFIG_SYS_PCIMSK1_MASK ~(CONFIG_SYS_PCI_MSTR_MEM_SIZE + CONFIG_SYS_PCI_MSTR_MEMIO_SIZE - 1U)


	#define CONFIG_SYS_DIRECT_FLASH_TFTP

	#if defined(CONFIG_CMD_JFFS2)
	#define CONFIG_SYS_JFFS2_FIRST_BANK 0
	#define CONFIG_SYS_JFFS2_NUM_BANKS CONFIG_SYS_MAX_FLASH_BANKS
	#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0
	#define CONFIG_SYS_JFFS2_LAST_SECTOR 62
	#define CONFIG_SYS_JFFS2_SORT_FRAGMENTS
	#define CONFIG_SYS_JFFS_CUSTOM_PART
	#endif

	#if defined(CONFIG_CMD_I2C)
	#define CONFIG_HARD_I2C 1 /* To enable I2C support */
	#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
	#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */
	#endif

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	#define CONFIG_SYS_RAMBOOT
	#endif

	#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 256KB for Monitor */

	#define CONFIG_SYS_DEFAULT_IMMR 0x00010000
	#define CONFIG_SYS_IMMR 0xF0000000

	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
	#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET


	/* Hard reset configuration word */
	#define CONFIG_SYS_HRCW_MASTER 0 /0x1C800641/ /* Not used - provided by CPLD */
	/* No slaves */
	#define CONFIG_SYS_HRCW_SLAVE1 0
	#define CONFIG_SYS_HRCW_SLAVE2 0
	#define CONFIG_SYS_HRCW_SLAVE3 0
	#define CONFIG_SYS_HRCW_SLAVE4 0
	#define CONFIG_SYS_HRCW_SLAVE5 0
	#define CONFIG_SYS_HRCW_SLAVE6 0
	#define CONFIG_SYS_HRCW_SLAVE7 0

	#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif

	#define CONFIG_SYS_HID0_INIT 0
	#define CONFIG_SYS_HID0_FINAL 0

	#define CONFIG_SYS_HID2 0

	#define CONFIG_SYS_SIUMCR 0x02610000
	#define CONFIG_SYS_SYPCR 0xFFFF0689
	#define CONFIG_SYS_BCR 0x8080E000
	#define CONFIG_SYS_SCCR 0x00000001

	#define CONFIG_SYS_RMR 0
	#define CONFIG_SYS_TMCNTSC 0x000000C3
	#define CONFIG_SYS_PISCR 0x00000083
	#define CONFIG_SYS_RCCR 0

	#define CONFIG_SYS_MPTPR 0x0A00
	#define CONFIG_SYS_PSDMR 0xC432246E
	#define CONFIG_SYS_PSRT 0x32

	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_BR (CONFIG_SYS_SDRAM_BASE \| 0x00000041)
	#define CONFIG_SYS_SDRAM_OR 0xF0002900

	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \| 0x00001801)
	#define CONFIG_SYS_OR0_PRELIM 0xFC000882
	#define CONFIG_SYS_BR4_PRELIM (CONFIG_SYS_BCSR \| 0x00001001)
	#define CONFIG_SYS_OR4_PRELIM 0xFFF00050

	#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100

	#endif /* __CONFIG_H */